Installation - Kenwood TK-7150 Service Manual

1. Installing Name Plate
Punch out the name plate card. Then insert the plates
onto the relative function keys.
You can reconfigure the name plates at any time.
Punch out the
name plate cards
Name plates for
the function keys
Squeeze and
insert the plates
Name plates
Side view of the key
Fig. 1
2. Ignition Sense Cable (KCT-18)
The KCT-18 is an optional cable to use the following func-
tions;
2-1. Ignition Function
The ignition function allows you to turn the transceiver's
power on and off with the ignition key of your car. When you
are driving with the ignition key on, the horn alert function is
disabled.
2-2. Timed Power Off Function
The timed power off function turns the transceiver's
power off the time specified with the programming software
(KPG-79D) after the ignition key is turned off. When you are
driving with the ignition key on, the horn alert function is dis-
abled.
The ignition sense function and the timed power off func-
tion can be used at the same time.
2-3. Modification
1. Remove the short plug from the accessory connector (6
pins) on the rear of the transceiver.
2. Cut off the end of the protective cover (accessory), insert
the KCT-18 into the protective cover, and insert it into pin
1 (IGN) of the short plug.
3. Install the short plug and protective cover on the connec-
tor on the rear of the transceiver, then clamp the bottom
of the protective cover with the supplied tie wrap.
Short plug
6
3
4
1
KCT-18
Protective cover
Fig. 2

INSTALLATION

Tie wrap
Cut
3. External Speaker (KES-5)
The external speaker output from the accessory connector
(6 pin) on the rear of the transceiver is 13W/4Ω. Use the KES-5.
3-1. Connection for the KES-5 with the TK-7150
■ When taking the AF output from the accessory
connector (6-pin) on the rear of the radio
The following tools are required for changing the connector.
• Extracting tool
The following extracting tool is recommended;
Molex inc. Order No. : J5800-002 (W05-0878-00)
1. Remove the connector with jumper from the external
speaker connector on the rear panel of the radio (Fig. 3-1).
Note : Save the jumper, which is required when the radio
is used without the external speaker.
2. Remove the terminals with the jumper from the connec-
tor housing holes number 5 and 6 using the extracting
tool.
Removing the jumper lead (Fig. 3-2)
1) Insert the extracting tool (J5800-002) into the connec-
tor while pushing the jumper lead in the direction of (a).
2) Push the extracting tool into collapse the barbs of the
crimp terminal.
3) Pull out the lead while continuing to push the extracting
tool in the direction (b).
3. Cut off the end of the protection cover, insert the KES-5
speaker cable into the protective cover.
4. Reinsert the terminal with the black and white stripe lead
into hole number 5, and the terminal with the black lead
into hole number 4 (Fig. 3-3).
5. Install the plug and protective cover on the accessory con-
nector on the rear of the transceiver, then clamp the bot-
tom of the protective cover with the supplied tie wrap.
Square-type plug
(E37-1031-05)
Extracting tool
(J5800-002)
Fig. 3-1
Short plug
5
Black/White lead
4
Black lead
Protective cover
Fig. 3-3
TK-7150
(a)
(b)
Jumper
lead
Crimp terminal
Barbs
Crimp terminal
(E23-0613-05)
Fig. 3-2
Tie wrap
Cut
Speaker cable (to KES-5)
7