Table of Contents
Advertisement
Quick Links
MS390 Series Installation Guide
About this Guide
This guide provides instruction on how to install and configure your MS390 series switch. This guide also provides mounting instructions and limited
troubleshooting procedures. For more switch installation guides, refer to the
Product Overview
Models
Model number
MS390-24-HW
MS390-24P-HW
MS390-24U-HW
MS390-24UX-HW
MS390-48-HW
MS390-48P-HW
MS390-48U-HW
MS390-48UX-HW
switch installation guides section
Stackable Layer-3 24-port Gbe switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 24-port Gbe POE+ switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 24-port Gbe UPOE switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 24-port mGbe UPOE switch with 10G/40G modular uplinks, hot-swappable
power supplies and hot-swappable fans
Stackable Layer-3 48-port Gbe switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 48-port Gbe POE+ switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 48-port Gbe UPOE switch with 10G/40G modular uplinks, hot-swappable power
supplies and hot-swappable fans
Stackable Layer-3 36-port 2.5Gbe and 12-port mGbe UPOE switch with 10G/40G modular uplinks,
hot-swappable power supplies and hot-swappable fans
on our documentation website.
Description
1
Advertisement
Table of Contents
Related Manuals for Cisco MERAKI MS390-24-HW
Summary of Contents for Cisco MERAKI MS390-24-HW
-
Page 1: About This Guide
Product Overview Models Model number Description Stackable Layer-3 24-port Gbe switch with 10G/40G modular uplinks, hot-swappable power MS390-24-HW supplies and hot-swappable fans Stackable Layer-3 24-port Gbe POE+ switch with 10G/40G modular uplinks, hot-swappable power MS390-24P-HW supplies and hot-swappable fans Stackable Layer-3 24-port Gbe UPOE switch with 10G/40G modular uplinks, hot-swappable power... -
Page 2: Technical Specifications
Each of the model has modular uplinks where you can choose from 3 different options of 10G and 40G SFP+ and QSFP+ uplink modules PoE/ UPoE Model Interfaces Power Load (idle/max) Available PoE Hot Swap Power Supply Capabilities MS390-24-HW 24 x 1GbE RJ45 79.2 / 99 W Yes, Dual MS390-24P-HW 24 x 1GbE RJ45 84.1 / 554.4 W 445W... -
Page 3: Front Panel Components
Front Panel Components Item Component LED Status Description Restore Restore button to clear switch IP and local configuration settings Power LED Solid amber Switch is unable to connect to the Meraki cloud Flashing white Firmware upgrade in process Solid white Switch is fully operational and connected to the Meraki cloud Switch does not have power Switch Ports... -
Page 4: Back Panel Components
Back Panel Components Item Component LED Status Description Management Interface Green Connected, used for easy access to the local status page Stack Ports Stack Cables are connected here Redundant Fans Green Active and operational StackPower Ports Stack Power cables are connected here Power Supplies Green Active and functional power supplies... - Page 5 MS390-24U Series front panel MS390-24UX Series front panel MS390-48 Series front panel MS390-48P Series front panel MS390-48U Series front panel MS390-48UX Series front panel MS390-48UX2 Series front panel...
-
Page 6: Package Contents
MS390 Series Back Panel Factory Reset Button If the button is pressed and held for at least 10 to 15 seconds and then released, the switch will reboot and be restored to its original factory settings by deleting all configuration information stored on the unit. Package contents... -
Page 7: Safety And Warnings
In addition to the MS switch, the following are provided: • 2 x (19 inch) Mounting brackets and screw kit that includes: ◦ 8 x Flat-head screws ◦ 4 x number-12 pan-head screws ◦ 4 x number-10 pan-head screws ◦ 1 x (4 x 20 mm) pan-head screw ◦... -
Page 8: Assigning An Ip Address
number of each switch, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need your Enterprise license key, which you should have received via email. 4. Go to the map / floor plan view and place each switch on the map by clicking and dragging it to the location where you plan to mount it. -
Page 9: Installation Instructions
Static IP via DHCP Reservations Instead of associating to each Meraki switch individually to configure static IP addresses, an administrator can assign static IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are “reserved” for the MAC addresses of the Meraki switches. Please consult the documentation for the DHCP server to configure DHCP reservations. - Page 10 2. Align the rack mount brackets on the sides of the switch onto the rack. 3. Secure and screw in the rack mount bracket on to the rack.
- Page 11 4. Insert the Uplink module.
- Page 12 Stack Cabling Installation • Connect the cable to the stack port on the switch back panel (as shown in the back panel diagram). Align the connector and connect the stack cable to the stack port on the switch back panel and finger-tighten the screws (clockwise direction).
-
Page 13: Basic Troubleshooting
If you are still experiencing hardware issues, please contact Cisco Meraki support by logging in to dashboard and using the Help option near the top of the page, then opening and email case or calling using the contact information on that page. - Page 14 Meraki MS390 devices have been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.