Culligan HE 1.25 Series Owner's Manual page 28

Performance
Data Sheet
Culligan HE
1.25 14" Water
Softener with
Soft-Minder®
Meter
28
01024584 E 11/19
Culligan knows the more informed you are about your water treatment systems, the more confident you will be
about its performance. It's because of this and more than seventy years of commitment to customer satisfaction
that Culligan is providing this Performance Data Sheet to its customers.
NOTICE Read this Performance Data Sheet and compare the capabilities of this unit with your actual
water treatment needs. It is recommended that before purchasing a water treatment unit,
you have your water supply tested to determine your actual water treatment needs.
Manufacturer: Culligan International Company
9399 W. Higgins Rd., Suite 1100, Rosemont, IL 60018 USA
(847) 430-2800
www.culligan.com
Product: Culligan High Efficiency 1.25 14" Water Softener with Soft-Minder
Testing Conditions & Results:
Flow Rate: 20.4 gpm @ 15 psi
Pressure: 30–40 psi (2.1–2.8 kg/cm2)
Acidity: Non-Corrosive
Temperature: 68°F (20°C)
Efficiency Rated Dosage†: 4,685 gr/lb
Softener Specifications:
Service Flow Rate: 20.4 gpm
Operating Temp. Range: 33–120°F (0–49°C)
Working Press. Range: 20–125 psi (1.4–8.5 kg/cm
Name of Substance
Barium
Radium 226/228
This system is certified for barium and radium 226/228 reduction based on hardness reduction.
It is recommended you test your water every six months to ensure the system is performing properly
and that hardness, and therefore barium and radium 226/228, are being reduced. Hardness test strips
have been included. Additional strips are available from your local Culligan dealer.
The Culligan High Efficiency 1.25 Series 14" Water Softeners with Soft-Minder® Meter are tested and certified
by WQA against NSF/ANSI Standard 372, CSA B483.1, and NSF/ANSI Standard 44 for the effective reduction
of hardness (calcium and magnesium), barium, and radium 226/228 as verified and substantiated by test data.
To maintain product certification and ensure uniform performance, the product is retested on a consistent basis.
The Culligan High Efficiency 1.25 Series 14" Water Softeners with Soft-Minder® Meter are certified by IAPMO
R&T against NSF/ANSI Standard 372, CSA B483.1, and NSF/ANSI Standard 44 for the effective reduction of
hardness (calcium and magnesium), barium, and radium 226/228 as verified and substantiated by test data. To
maintain product certification and ensure uniform performance, the product is retested on a consistent basis.
The Culligan High Efficiency 1.25 Series 14" Water Softeners are registered under California Water Treatment
Device Registration Number 3059. The Culligan High Efficiency 1.25 Series 14" Water Softeners with Soft-
Minder® Meter are registered under Iowa Water Treatment Device Registration Number 20664.
An efficiency rated water softener is a DIR softener which also complies with specific performance specifications
intended to minimize the amount of regenerant brine and water used in its operation. Efficiency rated water softeners
shall have a rated salt efficiency of not less than 3350 grains of total hardness exchange per pound of salt (based on
NaCl equivalency) (477 grams of total hardness exchange per kilogram of salt), and shall not deliver more salt than
its listed rating. The efficiency is measured by a laboratory test described in NSF/ANSI 44. The test represents the
maximum possible efficiency the system can achieve. Operational efficiency is the actual efficiency achieved after
the system has been installed. It is typically less than the efficiency due to individual application factors including
water hardness, water usage, and other contaminants that reduce the softener's capacity.
Refer to the Specifications, Familiarization and Warranty section of this Owner's Guide (P/N 01024584) for more specific
product information. To avoid contamination from improper handling and installation, your system should only be installed
and serviced by your Culligan dealer. Performance will vary based on local water conditions. The substances reduced by
this system are not necessarily in your water.
Culligan water softeners are designed to work with any salt of good quality, although it is recommended that
you ask your local Culligan dealer for his suggestion on the best type and grade of salt to use in this softener.
NOTICE This softener is not intended to be used for treating water that is microbiologically
unsafe or of unknown quality without adequate disinfection before or after the system.
The efficiency rated dosage is only valid at the 12 lb. salt dosage and maximum service flow rate for 14" models.
†
Buyer Signature _________________________________________________________
Seller Signature _________________________________________________________
Pressure Drop at Max. Flow Rate: 15 psi (71 kPa)
Max. Drain Flow Rate:
) Oper. Press. Range (Canada): 20–90 psi (1.4–6.3 kg/cm
2
USEPA Max. Contaminant Level
2.0 mg/L
5 pCi/L
Meter
®
Capacity: 56,218 grains @ 12.0 lb. salt
83,174 grains @ 24.0 lb. salt
91,662 grains @ 36.0 lb. salt
pH: 7.6
4.5 gpm
pH Flow Rate Pressure
7.5 + 0.5 20.4 gpm
7.5 + 0.5 20.4 gpm
Date ________________
Date ________________
)
2
15 (psig)
15 (psig)