Table of Contents
Advertisement
1-hour increments.
2. If you wish to shorten the time delay, keep on
pressing the time delay button until the time
delay you would like to set appears on the
screen.
Canceling the time delay
If you want to cancel the time delay countdown
and start the program:
1. Set the Time Delay to zero or turn the
Program selection knob to any program.
Thus, the time delay will be cancelled. The "
" (End/Cancel) light flashes continuously.
Then, select the program you wish to run
again.
2. Press "Start/Pause" button to start the
program.
Starting the Program
1. Press "Start/Pause" button to start the
program.
2. Program follow-up lamp showing the startup
of the program will light up.
If no program is started or no key is pressed
C
within 1 minute during program selection
process, the machine will switch to "Stand-
by" mode and the illumination level of the
temperature, speed and door indicators will
decrease. Other lights and indicators will turn
off. In case of turning the program selection
knob or pressing any button, lights and
indicators will turn on.
Progress of program
Progress of a running program is shown through
the program follow-up indicator. At the beginning
of every program step, the relevant indicator LED
will light up and light of the completed step will
turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the program
flow while the program is running. However, the
change to be made must be compatible with the
program step the machine is currently in. If the
change is not compatible, relevant lights will flash
for 3 times.
If the machine is not spinning, the program
C
may be in rinse hold mode or the automatic
spin correction system has been activated
due to an excessive unbalanced distribution
of laundry in the machine.
Changing the selections after the
program has started
Switching the machine to standby mode
Press the "Start/Pause" button to switch the
machine to pause mode while a program is
running. The light of the step which the machine is
in starts flashing in the program follow-up indicator
to show that the machine has been switched to
the pause mode. Also, when the door is ready
to be opened, "Door" light will also illuminate
continuously in addition to the program step light.
If necessary conditions to open the door are not
met, the "Door" light will remain off.
Changing the speed and temperature settings
for auxiliary functions
Auxiliary functions can be cancelled or selected, or
the spin speed and temperature settings can be
changed in accordance with the step the program
is in. If the change can not be made, relevant light
will flash for 3 times.
Adding/removing laundry in pause mode
If the "Door" light flashes while the machine is in
pause mode, it means that the conditions (low
water level, etc.) to open the door have been
met and the period of approx. 1 or 2 minutes to
open the door has started. "Door" lamp will light
up continuously when the door is unlocked. Door
can be opened to load or unload the laundry after
this moment. If the front door cannot be opened
because of a safety reason after the machine has
been switched to the pause mode by pressing the
"Start/Pause" button, the "Door" light will continue
to remain off. Nevertheless, the follow-up light of
the relevant program in which the machine was
taken to "Pause" mode will flash.
Door lock
The loading door can be opened once the
"Door" lamp stops flashing and starts lighting up
continuously.
Child-proof lock
Protect the appliance from being tampered by
children by means of the child-proof lock. In this
case, no change can be made in the running
program.
If the program selection knob is turned when
C
the child-proof lock is activated, "Con" label
will be displayed. In this case, any change in
temperature, speed and auxiliary functions
which are already selected for the programs is
not allowed.
If the program selection knob is turned to
C
"On/Off" position and then another program
is selected while a program is running, the
previously running program will resume
operating.
The machine is switched to child-lock by pressing
the 1st and 2nd auxiliary functions for 3 sec.
While the lights on the auxiliary function buttons
1 and 2 are flashing during 3-second press and
hold process, C03, C02 and C01 labels will be
displayed respectively. Then the label "Con" will
be displayed to show that the child-proof lock
is activated. The same label will also appear on
the screen when any button is pressed or when
the program selection knob is turned while the
machine is in child-proof lock mode.
Furthermore, the lights on the auxiliary function
buttons 1 and 2 blink 3 times to show how to exit
Child-proof Lock mode.
To deactivate the childproof lock:
a) Press the auxiliary function buttons 1 and 2
for 3 sec. while any program is running. While
9 - EN
Hide quick links:
Advertisement
Table of Contents
