Download
Share
Print this page
Entrematic E1T Installation Manual
  1. Manuals
  2. Brands
  3. Entrematic Manuals
  4. Control Panel
  5. E1T
  6. Installation manual

Entrematic E1T Installation Manual

For automations with one 400 v three-phase motor
Hide thumbs

Advertisement

Quick Links

Download this manual
Entrematic E1T
Installation manual for control panel for automations with one 400 V
three-phase motor.
EL07L
1
J7
DO NOT
USE
DO NOT
SO
USE
+LK -
ON
RP
TC
11
17
12
IN
17 14 12 11
0
0
PT3
PT4
J1
COM
EO
ON
OFF
1
2 3 4 5 6
SA
POWER
0 1 1 2 3 4 6 8 9 20 41
www.entrematic.com
J2
GOL4
Transformer
L1 L2 L3
F3 F2 F1
Power supply
Technical manual
EL07PW1
F4
Motor
3~
IP1897EN

Advertisement

loading
Need help?

Need help?

Do you have a question about the E1T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Entrematic E1T

Summary of Contents for Entrematic E1T

  • Page 1 Entrematic E1T Installation manual for control panel for automations with one 400 V three-phase motor. EL07L EL07PW1 GOL4 DO NOT Transformer Motor DO NOT +LK - 2 3 4 5 6 POWER L1 L2 L3 17 14 12 11 0 1 1 2 3 4 6 8 9 20 41...

  • Page 2: Table Of Contents

    INDEX Subject Page eneral safet precautions EC declaration of conformit Technical data 3.1 Applications Connection of power suppl Commands FA1- FA2 self-controlled safet ed e Outputs and accessories Adjustments Start-up Trou leshootin 10. Example application for slidin ates 11. Example application for sectional overhead doors CAPTION This s m ol indicates instructions or notes re ardin safet issues which re uire particular attention.

  • Page 3: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS This installation manual is intended for uali ed personnel onl . The installation, the power connections and the settin s must e completed in conformit with or in Methods and with the re ulations in force. Before installin the product, carefull read the instructions. Bad installation could e ha ardous. The pac a in materials (plastic, pol st rene, etc.) should not e discarded in the environment or left within reach of children, as these are a potential source of ha ard.

  • Page 4: Ec Declaration Of Conformit

    Manufacturer: DITEC S.p.A. Address: via Mons. Ban , 3 21042 Caronno P.lla (VA) - ITALY declares that the control panel E1T is in conformit with the provisions of the followin EC directives: EMC Directive 2004/108/EC; Low Volta e Directive 2006/95/EC.

  • Page 5: Commands

    COMMANDS Command Function Description N.O. AUTOMATIC The permanent closin of the contact ena les automatic clos- CLOSING in . N.O. OPENING ith DIP1 ON, the closin of the contact activates the openin operation. STEP-BY-STEP ith DIP1 OFF, the closin of the contact activates openin or closin operations in the followin se uence: open-stop-close- open.

  • Page 6: Outputs And Accessories

    OUTPUTS AND ACCESSORIES Output Value - Accessories Description Accessories power supply. Power suppl output for external ac- cessories, includin automation status lamp. 24 V 0.5 A Open automation lamp. The li ht switches off when the automa- 24 V 3 W tion is closed.

  • Page 7: Adjustments

    ADJUSTMENTS Description DIP1 Command 1-3 operation. Step- -step. Openin . NOTE: it also sets operating mode of the plugin cards connected on AUX1 and AUX2. DIP2 Restore automatic closing time. 100% DIP3 3 seconds pre ashing. Disa led durin openin . Ena led for oth openin Ena led onl with automatic...

  • Page 8: Start-Up

    START-UP WARNING WARNING The operations in point 3 are performed without safety devices. The operations in point 3 are performed without safety devices. The trimmer can only be adjusted with the automation idle. The trimmer can only be adjusted with the automation idle. Ma e a jumper for the N.C.

  • Page 9: Troubleshooting

    TROUBLESHOOTING Problem Possible causes Remedy The automation does not No power. Chec that the control panel is pow- open or close. (POWER led off). ered correctl . Short circuited accessories. Disconnect all accessories from termi- (POWER led off). nals 0-1 (volta e must e 24 V ) and reconnect one at a time.
  • Page 10 10. EXAMPLE APPLICATION FOR SLIDING GATES DIP4=OFF 1 2 3 4 5 6 (Fi . 10.1) When the control panel is used in applications for slidin ates: 17 14 12 11 0 1 1 2 3 4 6 8 9 20 41 set DIP4=OFF;...

  • Page 11: Example Application For Sectional Overhead Doors

    11. EXAMPLE APPLICATION FOR SECTIONAL OVERHEAD DOORS DIP1=ON DIP2=ON DIP4=OFF 1 2 3 4 5 6 (Fi . 11.1) When the control panel is used in applications for sectional overhead doors: 17 14 12 11 0 1 1 2 3 4 6 8 9 20 41 set DIP1=ON;...
  • Page 12 Entrematic Group AB Lodjursgatan 10 SE-261 44, Landskrona Sweden www.ditecentrematic.com...