Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Boumatic Xpedia 360IX
Summary of Contents for Boumatic Xpedia 360IX
- Page 1 Xpedia™ 360IX Feeding System Installation Instructions www.boumatic.com BouMatic Global Headquarters PO Box 8050 Madison, WI 53708-8050 Tel: 608.222.3484 Fax: 608.222.9314 BouMatic Europe Rue Jules Melotte 31 4350 Remicourt Belgium Tel: +32 19 54 42 66 Fax: +32 19 54 55 44...
- Page 2 Under no circumstances These instructions aim to aid those responsible (outlined under “Re- will BouMatic be responsible for any problems caused in whole sponsibilities”) for installing, operating, maintaining, troubleshooting, or in part by and deviation from the procedures specified in and servicing this product.
-
Page 3: Table Of Contents
2.8 Installation of Feed Hopper ................... 14 2.9 Finger Switches ......................15 2.10 Electrical Installation ....................16 2.10.1 Feed Dispenser Control .................. 16 2.10.2 Main Control Panel Safety Switches ..............16 2.10.3 Brake Resistor ....................19 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 4: Introduction
• Bolt or tack weld parts in place, as required, until the entire installation is complete. Then, after all adjustments have been made, fully weld the joints. 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 5: Installation
36/4 5640 6300 6964 7626 8287 8949 222.0 248.0 274.2 300.2 326.3 352.3 2726 2474 2418 2273 2163 2157 107.3 97.4 95.2 89.5 85.2 84.9 Concrete layout and installation of posts l997_1 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 6: Feed Manger Assemble
U-Bolt length and smooth. (See Figure 3.) Grind off excess and smooth Alignment of feed manger l997_2 Upright Post Feed manger mounting Assemble feed manger l997_3 l997_4 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 7: Brisket Rails
(Figure 5a) for the front rail using M12x90 Bolts at the angle speci- fied in Figure 5b. Entry Guide Rail Supports Cow Exit Cow Entrance 10° 8° l997_5B l997_5A Installation of rails and support posts l997_6 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 8: Cow Entrance Pinch Gate
2. Weld the hinge brackets to the cow entrance upright post. (See Figures 6a and 6b.) 3. Secure the sensor mechanism. (See Figure 7.) Pinch gate clearance l997_6A Entrance Upright Post Weld Pinch gate assembly l997_6B 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 9: Middle Swing Gate
2. Weld the Hinge Brackets to the cow entrance side of the wall plate post. (See Figure 8.) Manager Support Arm Centered in Gap Weld Hinge Brackets Middle swing gate installation l997_8 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 10: Exit Pinch Gate
2. Weld the Hinge Brackets to the cow entrance side of the wall plate post. (See Figure 9.) 3. Secure the sensor mechanism. (See Figure 10.) Weld Hinge Brackets Exit pinch gate installation l997_9 Exit pinch gate sensor l997_10 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 11: Man Access Gate
Front Rail will need a section removed 590mm to install the Man Access Gate. (See Figure 12.) Internal gate installation l997_24 Man passage l997_11 Man passage installation Internal gate installation l997_12 l997_25 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 12: Installation Of External Rails
Attach the bent sections of the ex- ternal rails to the brackets as shown. (See Figure 15.) External rail brackets at man passage l997_13 External rail installation at support posts l997_14 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 13: Positioning At Cow Entrance/Exit
(Figure 16). At the man U-bolts passes, secure the ends of the two outer rails with U-bolts and the inner rail by welding (Figure 18). Installation of Bottom Rails l997_26 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 14: Installation Of Feed Hopper
If the ID is read at the Texas gate, the dispenser cure to concrete using (12 __ bolts) must be installed at the 2nd stall position. If the ID Second Stall Position Third Stall Position Feed dispenser location l997_17 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 15: Finger Switches
These must be mounted as shown in Figures 20 and 21. Feed dispenser sensors l997_18 Sensor trigger bolt on feed manger l997_19 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... -
Page 16: Electrical Installation
See Figure 22. the new sensor (DE4) onto DE2 or DE3 (consult fig- ure 37 in 9e-879, page 86). See Figure 23. Feed dispenser control l997_20 Exit pinch gate sensor wiring l997_21 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13... - Page 17 Manual 9e-879. See Figure 24. The man pass and pull-cord electrical cable should be run through the outside perimeter rail. (See Figure 25 on the following page.) Man passage sensor wiring l997_22 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13...
- Page 18 Cable running for safety sensors l997_23 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13...
-
Page 19: Brake Resistor
PA+ and PB on the resistor with the matching terminals on the VSD. See Figure 26 for an example of how to mount the brake resistor. Mounting the Break Resistor l997_27 9e997 Xpedia 360IX Feeding System Installation Instructions 3/21/13...
Need help?
Do you have a question about the Xpedia 360IX and is the answer not in the manual?
Questions and answers