Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Attero Tech unA4O AES67
Summary of Contents for Attero Tech unA4O AES67
- Page 1 AES67 Four Output Interface Attero Tech LLC 2018 614-00048 Rev 01 4/23/2018...
-
Page 2: Important Safety Instructions
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by Attero Tech 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. - Page 3 Should any defect develop, Attero Tech, LLC will, at our option, repair or replace any defective parts without charge for either parts or labor. If Attero Tech, LLC cannot correct the defect in the equipment, it will be replaced at no charge with a similar new item.
-
Page 4: Table Of Contents
Contents 1 – Overview ..................................................5 1.1 – What’s in the Box ....................................5 1.2 – Optional Extras ....................................... 5 2 – Device Installation ............................................... 7 2.1 – Mounting ........................................ 7 2.2 – Status LEDs ......................................8 2.3 – Hardware Connections ................................... 8 2.3.1 –... -
Page 5: Overview
1 – Overview Figure 1 - unA4O front and back The unA4O is a 4 output AES67 audio interface. It's ideal for 1.1 – What’s in the Box adding 4 analog outputs driven from up to 4 different AES67 audio streams in a small, unobtrusive form factor for installed The unA4O comes supplied with the following: sound applications. - Page 6 DEVICE FEATURES FRONT PANEL REAR PANEL 1 – Status LEDs 3 – Power Socket – Use with optional 24V DC wall wart only 2 – Recessed Factory Reset Switch 4 – Ethernet interface connector and indicators 5 – 4 x Balanced line audio outputs *Note: The unA4O has a label on one of the mounting flanges that shows the MAC address.
-
Page 7: Device Installation
2 – Device Installation 2.1 – Mounting It is recommended that the unit be secured to a flat surface with a screw through each mounting flange. Dimensions for mounting are show in the Figure 2 below. Use a No. 6 screw of a type and size that is applicable to the surface to which the unA4O will be attached. Figure 2 - Mounting Information *Notes for mounting: All connections to the unA4O should be If all steps are performed correctly, the power light on the front... -
Page 8: Status Leds
2.2 – Status LEDs 2.3 – Hardware Connections The front panel LED’s show the AES67 diagnostic status. If The unA4O drives either unbalanced or balanced audio devices. network or audio problems persist, these LED’s may assist in Refer to the following diagrams and instructions for connecting resolving the issue. -
Page 9: Device Configuration
To ensure communication, the PC can either be set to get a The audio routing is also done using Attero Tech’s unIFY Control dynamic IP address, or be given a static IP address in the range Panel. -
Page 10: Factory Reset
******************************************************************* The unA4O has the ability to be updated. Updates are applied IMPORTANT via the network using Attero Tech unIFY Control Panel’s Smart ******************************************************************* Firmware update facility. The latest unA4O SFU file is available The factory reset returns the entire device to its factory defaults. -
Page 11: Architects & Engineers Specification
The unit shall accept either +24VDC or IEEE 802.3af standard PoE as power input. The unit shall be compliant with FCC 47CFR Parts 15B and 18 (Class A), EN 55011, ICES-003, CE (EN55022 Class A and EN55024 Class A), and RoHS requirements. The unit shall be the Attero Tech unA4O Output Interface 4.1 – Device Specifications...
Need help?
Do you have a question about the unA4O AES67 and is the answer not in the manual?
Questions and answers