Attero Tech unAIO2X2+ User Manual

2x2 aes67 interface

Advertisement

unAIO2X2+
User Manual
unAIO2X2+
2x2 AES67 Interface
User Manual
Date 03/21/18
Revision 01_b
 Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone 260-496-9668 • Fax 260-496-9879
www.atterotech.com
614-00040

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the unAIO2X2+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Attero Tech unAIO2X2+

  • Page 1 User Manual unAIO2X2+ 2x2 AES67 Interface User Manual Date 03/21/18 Revision 01_b  Attero Tech, LLC 1315 Directors Row, Suite 107, Ft Wayne, IN 46808 Phone 260-496-9668 • Fax 260-496-9879 www.atterotech.com 614-00040...
  • Page 2 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by Attero Tech 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
  • Page 3 If Attero Tech, LLC cannot correct the defect in the equipment, it will be replaced at no charge with a similar new item. Attero Tech, LLC will pay for the cost of returning your equipment to you.
  • Page 4: Table Of Contents

    3.4 – 3rd Party Control ..............................4 3.5 – Using the Command interface ..........................4 4 – ARCHITECTS & ENGINEERS SPECIFICATION .............................. 5 4.1 – Device Specifications ..............................5 APPENDIX A - Reference Documents ................................A-1  Attero Tech LLC 2018 Page 3 614-00040 Rev 01...
  • Page 5: Overview

    Figure 1 - unAIO2X2+ front and back Attero Tech unIFY Control Panel application can be used to configure the device-specific features. It is also used to configure its AES67 transmit and receive streams as well. The unAIO2X2+ also supports control by third party systems allowing external configuration of its settings such as phantom power and input gain in real time.
  • Page 6: Device Installation

    6 digits make up part of the devices default network name. The full MAC address is also given on the bottom of the unit.  Attero Tech LLC 2018 Page 5 614-00040 Rev 01...
  • Page 7: Mounting

    There may also be some activity on the unAIO2X2+ Ethernet connector LED indicators. With no network, both LEDs will remain off. If an active connection is made both LEDs will come on and if there is network activity, the yellow LED will then flash.  Attero Tech LLC 2018 Page 6 614-00040 Rev 01...
  • Page 8: Status Leds

    PTP error / no PTP sync / PTP disabled System booting Green PTP sync, slave Orange Ethernet connection lost Flashing PTP sync, master Green Green AES67 Interface ready Color Description Assigned AES67 stream not being received  Attero Tech LLC 2018 Page 7 614-00040 Rev 01...
  • Page 9: Hardware Connections

    2.3.2 – Balanced Output to an Unbalanced Input Balanced Output Terminal Block Plug TS Plug Sleeve 2-Wire Cable Balanced Output RCA Plug Terminal Block Plug Sleeve 2-Wire Cable Figure 4 – Unbalanced Wiring Guide  Attero Tech LLC 2018 Page 1 614-00040 Rev 01...
  • Page 10: Unbalanced Output To An Balanced Input

    2.3.3 – Unbalanced Output to an Balanced Input Balanced Input Terminal Block Plug TS Plug Sleeve 2-Wire Cable Balanced Input Terminal Block Plug RCA Plug Sleeve 2-Wire Cable Figure 5 – Unbalanced Wiring Guide  Attero Tech LLC 2018 Page 2 614-00040 Rev 01...
  • Page 11: Device Configuration

    The audio routing is also done using Attero Tech’s unIFY Control Panel. There is a tab on the devices configuration for each unit specifically for setting up receive and transmit streams.
  • Page 12: Factory Reset

    3.4 – Firmware Updates The unAIO2X2+ has the ability to be updated. Updates are applied via the network using Attero Tech unIFY Control Panel’s Smart Firmware update facility. The latest unAIO2x2+ SFU file is available from the Attero Tech customer portal.
  • Page 13: Architects & Engineers Specification

    The unit shall accept either +24VDC or IEEE 802.3af standard PoE as power input. The unit shall be compliant with FCC 47CFR Parts 15B and 18 (Class A), EN 55011, ICES-003, CE (EN55022 Class A and EN55024 Class A), and RoHS requirements. The unit shall be the Attero Tech unAIO2x2+ I/O Interface 4.1 – Device Specifications Audio Inputs:...
  • Page 14: Appendix A - Reference Documents

    User Manual APPENDIX A - Reference Documents The following table lists the relevant reference documents. Document Title Location unIFY 3 Party Software API Registered users area on website  Attero Tech LLC 2018 Page A-1 614-00040 Rev 01...
  • Page 15 Updated Device installation image 00_d 11/14/17 Update status LED states 11/16/17 Initial Release 01_a 03/15/18 Warranty Updated 01_b 03/21/18 Bug #5164 - AES67 quick start guide reference in config section  Attero Tech LLC 2018 Page i 614-00040 Rev 01...

Table of Contents