0800 328 6250 www.samsondoors.co.uk safe • timeless • beautiful Conservatory awnings − shade for large areas markilux 8800 | pergola 110 / 210 | pavillon What to to do, if... markilux pavilion markilux 8800 This booklet describes in simple words the necessary assembly steps in case any problems occur.
Press the belt clamp (29) and release reclamped, proceed acc. Chapter the drive belt (19) carefully a little 7., Points 5. and 6. way at a time until there is no more tension on the clamping module. www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
(2) in the direction of the middle of the awning, release the tension on the inside clamping module so that the splint (23) can be pulled out easily (right and left). The awning is now under tension. www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
Release the tension on each belt bit by bit and check progress by retracting the awning again slowly until it closes again. www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
NOTE: During the initial retraction and extension of systems with a projection exceeding 5 m, a tighter winding of the cover onto the roller tube might occur. This may lead to a decrease in cloth tension or to a lower clamping module tension. See Chapter 9. www.markilux.com www.samsondoors.co.uk 0800 328 6250...
4. Install a new clamping module into the guide rail. 5. Retract the drive belt back into the drive belt clamp and clamp the awning (see Chapter 3., from Point Fig.: Drive belt progression with clamping module, right and left www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
(46). If necessary, the Velcro fastener can also be retightened with staples. 4. Mount the belt clamp holder (46) back into the projection profile (2) and apply the cap closure. www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
(31) via the roller tube system, first release the additional groove (27). screws (32) of the tracfix terminal on Clean the roller tube, cassette and the carriage. projection profile after inserting a new cloth! www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
(2). drive belt from the carriage. 5. Fasten the belt clamp holder (46) again with the socket head cap screw with hexagon socket, key width 6 (39). Reapply the cap closure (21). www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
(34) can be pulled out of the tube. 7. Put the system back into operation and program the positioning of the end positions with the adjustment set, see Chapter 18 (standard motor without radio). www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
5. Reinstall the belt clamp (29) after pulling through the drive belt (19) (see Chapter 11). 6. Fasten the drive belt clamping loop onto the roller tube, see Chapter 4. 7. Reclamp the awning, see also Chapter 3, from Point 3. www.markilux.com www.samsondoors.co.uk 0800 328 6250...
7. If the connection of the projection profile is not parallel, adjust through the insertion of fabric wads on the roller tube, see Chapter 16. 8. In case of systems with radio remote control, the battery must be replaced. www.markilux.com www.samsondoors.co.uk 0800 328 6250...
Adjustment instructions for radio motors with 433 MHz technology For radio motors, markilux provides the additional booklet "Adjustment instruction for radio motors with 433 MHz technology". This booklet describes in simple words the adjustment of markilux awnings via radio, and any problems which may occur.
4. Now release the reset/programming button and continue to keep the travel button pressed. 5. In addition, press the reset/programming button again. The tube drive will make a "click-click" sound in acknowledgement. The end positions are now deleted. www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
Page 15
L1 (Phase, brown or black) motor Plug-in coupling for "Becker" standard motor, connection line 4 x 1.5 mm² H05RR-F 4 G 075 sw Neutral (blue) High/low command (black) High/low command (brown) PE = Protective conductor PE (green-yellow) www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
What to do if the end positions on a Becker standard drive cannot be adjusted as described? Overview of different adjustment sets for the "Becker" standard motor Awning extension Awning retraction Reset / programming button www.markilux.com www.samsondoors.co.uk 0800 328 6250 www.samsondoors.co.uk...
Page 17
Important general guidelines for the "What to do if ...? This "What to do if ...?" does not replace the enclosed markilux original instructions and the associated documents for the motors and controls. It is merely intended to promote understanding of the product functionality.