■ Automatic operation pag. Index 1. NIGHT PROGRAM C1 menu pag. 1.1 NIGHT C1 display pag. 1.2 Change NIGHT C1 pag. ■ Safety warnings 2. Menu HOLIDAY PROGRAM pag. pag. ■ Technical characteristics 2.1 Creating a HOLIDAY program pag. pag. ■...
SAFETY WARNINGS TECHNICAL CHARACTERISTICS 1) The instrument must be installed and activated by qualified personnel, following the connection diagrams provided in this manual scrupulously. 2) After installation, it must be made impossible to access the terminals without specific tools 3) Before accessing the connection terminals, verify that the leads are not live 4) Do not connect or power the instrument if any part of it is damaged...
“R” INSTALLATION Note: in the case of a mains power failure, IR reception is not activated. so that the (+) pole is visible as shown in the “Battery replacement” “ ” IR Interface”...
P3 program P5 program P5 ON Sunset Sunrise P3 OFF P3 ON Sunset Sunrise P6 program P4 program Sunrise Sunset P6 ON P6 OFF P4 OFF Sunset Sunrise Note: the relay 2 has a program set to P1 (it cannot be modified). The selection of the night-time behaviour is therefore only limited to relay 1.
1.1 NIGHT C1 display AUTOMATIC OPERATION “ ” “C1” C2” “Ok” “C1” and “C2” “Ok” “C1” and “C2” Note: the display of the P3 program 1. NIGHT PROGRAM C1 menu is divided into two screen shots, the first one showing the switch off time and the second time the switch back on time.
To go from one screen to the other, press keys “C1” and “C2”. P1: no parameter P2: no parameter P3: night switch off time, night switch on time P4: night switch off time P5: night switch on time P6: initial time of the impulse, duration of impulse “Ok”...
2. Menu HOLIDAY PROGRAM 2.1 Creating a HOLIDAY program “Ok” “ ” “C1” and “C2” “Ok” “C1” and “C2” Note: recursive function “Ok” At this point, the instrument activates the “Ok” recursive function that makes is possible to program multiple holiday days in series periods).
“Ok” “C1” and “C2” “Ok” “C1” and “C2” 2.2 Checking a program “C2” “Ok” 2.2.1 Displaying a program HOLIDAY 2.2.2 Changing a program HOLIDAY “ ” “C1” and “C2” “Ok” “Ok” “C1” and “C2” “Ok” “Ok”...
“Ok” “ ” SETTINGS MENU “C1” and “C2” “Ok” DATE menu “C1” and “C2” “Ok” “ ” “Ok” “C1” and “C2” “ ” “C1” and “C2” “Ok” “Ok” “C1” and “C2” “Ok” LANGUAGE menu TIME menu “C1” and “C2” “C1” and “C2” “Ok”...
HOUR METER MENU RESET MENU “ ” “C1” and “C2” “ ” “Ok” “C1” and “C2” “Ok” “C1” and “C2” “C1” and “C2” “Ok” “Ok” “Ok” “Ok” “Ok” To perform a complete instrument reset, restoring the factory settings, “ ” use a sharp instrument to press the “R”...
AST2 memo AST2 “R” Note: during transmission, point the remote control towards the front of the instrument to facilitate the transmission. A possible - 24 -...
BATTERY REPLACEMENT REFERENCE STANDARDS 2006/95/EC “ ” 2004/108/EC EN 60730-2-7 Use CR-2032 batteries only. Throw away the run down batteries in compliance with current regulations on the disposal of harmful waste.
Need help?
Do you have a question about the memo AST2 and is the answer not in the manual?
Questions and answers