Table of Contents
Advertisement
8.
EPPROM
View the type of EEPROM memory module plugged into the CS-IPRO.
IPRO-X
The CS-IPRO comes with a removable EEPROM memory module. The EEPROM
memory module inserts into the connector located on the front face of the CS-IPRO,
and may be removed for safe storage.
The EEPROM type is factory configured for parameter (P) or firmware (F) operation.
A parameter EEPROM is used to backup the DMX channel patch configuration. A
firmware EEPROM is used to update the current firmware version running on the CS-
IPRO microcontroller to the firmware version saved on the EEPROM.
The EEPROM memory module supplied with all CS-IPRO is a parameter type.
IPRO-P
Indicates the EEPROM memory module is for a CS-IPRO microcontroller.
IPRO-P
Indicates the EEPROM type is configured for parameter (P) operation.
XXXXXX
Press EXECUTE to display the silicone serial number parameter.
DISABLED
Press EXECUTE and menu feature is disabled for factory use only.
IPRO-F
Indicates the EEPROM type is configured for firmware (F) operation.
VER X.X
Press EXECUTE to display the version (VER) of the firmware.
DISABLED
Press EXECUTE and menu feature is disabled for factory use only.
PROD ERR
Indicates the wrong product type of EEPROM memory module is detected.
NO MEM !
Indicates an EEPROM memory module has not been detected (not installed).
9.
EEPROM
Load new firmware into the CS-IPRO via the EEPROM memory module.
FW-LOAD
If a firmware update is required, Johnson Systems Inc. may supply an EEPROM
memory module with the latest firmware version. The firmware EEPROM memory
module can be inserted into the EEPROM memory module connector and the
firmware can then be loaded into the CS-IPRO microcontroller.
EEPROM
Press EXECUTE to enter the menu.
DISABLED
This menu is disabled for inadvertent use. Proceed to enable.
ENABLED
Press and hold MENU (
MEMCHECK
Automatically checks the EEPROM memory module for firmware type.
CRC-TEST
Automatically does a CRC test on the firmware code in the EEPROM.
>>>>>>>>
The CRC test in progress.
VER X.X
Displays the firmware version on the EEPROM memory module.
UPDATE ?
Press EXECUTE to proceed.
SURE ???
Press EXECUTE to proceed.
UPDATING
Firmware update in progress.
WILL
Firmware update in progress.
AUTO
Firmware update in progress.
RESTART
Firmware update in progress.
PLEASE
Firmware update in progress.
WAIT....
When firmware update is complete the LCD backlight flashes and restarts.
NO MEM !
Indicates an EEPROM memory module has not been detected (not installed).
WRONG
Indicates if the wrong type (parameter) of EEPROM memory module detected.
MEM TYPE
Indicates if the wrong type (parameter) of EEPROM memory module detected.
WRONG
Indicates if the wrong product type of EEPROM memory module detected.
PRODUCT
Indicates if the wrong product type of EEPROM memory module detected.
CRC ERR!
Indicates if the CRC test fails and the EEPROM memory module is defective.
10. EDIT KEY
Edit the security key for the CS-IPRO.
SECURITY
The 8-digit security key for the CS-IPRO can be edited to any combination of digits.
The default security key is set at all zeros (00000000).
The purpose of the security key is to provide security against other CS-IPRO
programmers inadvertently making changes to the DMX channel patch on a CS-DMX
control station. With the security jumper on a CS-DMX control station installed in the
enabled position, the security key in the control station must match the security key in
the CS-IPRO to make any changes.
EDIT KEY
Press EXECUTE to enter the menu.
00000000
Displays the 8 digit security key to be edited.
00000000
Press EXECUTE to move the cursor to the right, under the digit to be edited.
www.johnsonsystems.com
) and MENU (
) at the same time for 4-5 seconds.
9
Advertisement
Table of Contents
