Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for JOHNSON SYSTEMS CS-IPRO
-
Page 1: User Manual
User Manual CS-IPRO Wireless Hand-Held Programmer for CS-DMX Series Control Stations JOHNSON SYSTEMS INC. www.johnsonsystems.com 1923 Highfield Crescent S.E. Calgary, Alberta, Canada T2G 5M1 tel: 403.287.8003 fax: 403.287.9003 e-mail: info@johnsonsystems.com website: www.johnsonsystems.com... -
Page 2: Table Of Contents
System Configuration Menu Items ........7 Typical Application Procedures..............11 Warranty The CS-IPRO comes with a standard two (2) year limited warranty against defects in parts and workmanship. User Manual Copies Additional copies of the most recent version of this manual can be downloaded at: http://www.johnsonsystems.com/cs_ipro_user_manual.htm. -
Page 3: Introduction
CS-IPRO when used in conjunction with a hand-held infrared printer (Johnson System Inc., Part Number: JS-IP). The maximum range for sending data from the CS-IPRO to the hand-held infrared printer is 6' (1.8 m). Specifications • Enclosure Dimensions: Width 2.75" (70 mm) x Height 4.95" (125 mm) x Depth 0.95"... -
Page 4: Battery Replacement
Alkaline or Nickel Metal Hydride (NiMh) ONLY! Ensure batteries are installed as indicated inside the battery compartment. The combined voltage of the batteries must be greater than 1.9 VDC for the CS-IPRO to power on. Security If the SECURITY jumper on the rear of CS-DMX control station is installed in the ENABLED position, the security KEY set in the CS-IPRO must match the security KEY set in the CS-DMX control station to make any changes to the DMX channel patch configuration. -
Page 5: System Status - Lcd Display
System Status - LCD Display The top line of the LCD display always shows “JSI IPRO” unless the configuration menu items are being accessed. The bottom line of the LCD display shows the current status. In normal run mode it will show “>REMOTE<”. -
Page 6: Quick Programming Reference To System Configuration Menu Items
Load the DMX channel patch from the removable EEPROM Memory Module. PATCH Loads and saves the patch into the CS-IPRO memory. EEPROM View the type of EEPROM memory module plugged into the CS-IPRO. IPRO-X EEPROM Load new firmware into the CS-IPRO via the EEPROM memory module. -
Page 7: Detailed Programming Of System Configuration Menu Items
Edits the patch saved in the CS-IPRO memory only. Each of the sliders on a CS-DMX control station can be assigned to control any combination of DMX channels from 1 to 512. The patch is saved in the CS-IPRO memory. - Page 8 The existing DMX channel patch is read from the CS-DMX control station and loads the patch into the CS-IPRO transfer buffer. The data is checked and verified and then loaded into the CS-IPRO memory. The patch can then be viewed in the CHECK PATCH menu or modified in the EDIT PATCH menu.
- Page 9 Edit the security key for the CS-IPRO. SECURITY The 8-digit security key for the CS-IPRO can be edited to any combination of digits. The default security key is set at all zeros (00000000). The purpose of the security key is to provide security against other CS-IPRO programmers inadvertently making changes to the DMX channel patch on a CS-DMX control station.
- Page 10 Once the security key for the CS-DMX control station has been set, and the security jumper is installed in the enabled position, the security key set in the CS-IPRO must match the security key in the control station to make any changes.
-
Page 11: Typical Application Procedures
(backup) the DMX channel patch into the EEPROM memory module. Edit the DMX channel patch for a CS-DMX control station. A) GET CS PATCH load the DMX channel patch from the CS-DMX control station into the CS-IPRO. B) EDIT PATCH edit and reconfigure the DMX channel patch for each slider as required. - Page 12 3 button entrance station w/on, preset, and off 1 gang 1.80"W x 2.75"H x 2.00"D 6 x #18 AWG 4.6cm x 7.0cm x 5.1cm CS-IPRO Hand-held Infrared Station Programmer Wireless 2.75"W x 4.95"H x 1.00"D (70cm x 125cm x 25cm) DMX-6PIM...