tau SPIN Use And Maintenance Manual page 15

1. DIMENSION OF GEARMOTOR (fig. 1)
2. INSTALLATION WITH A CENTRALIZED MOTOR (fig. 2)
This type of installation is possible where there are no other doors in the overhead garage door; it is recommended where overhead garage
door surface is less than 7 m².
2.1 INSTALLATION MATERIALS (fig. 3)
1 (Art.150KITB1S):
Blistered pack of accessories containing:
2 (Art.150KITBCL1)*:
3 Gearmotor, series SPIN, complete with:
Blistered pack of accessories containing:
* The curved telescopic arms are used when the distance between the overhead door and its frame is less than 15 mm (fig. 2).
2.2 FIXING THE LONGITUDINAL FRAME MEMBER (fig. 4)
1. Place the longitudinal frame member slightly to the left or right of the handle.
2. Use suitable self-threading screws to fix it to the frame of the overhead garage door.
2.3 INSTALLING THE GEARMOTOR
1. Find the right position for fixing the gearmotor according to the measurements given in fig. 5.
2. Insert the stud screws and tighten the nuts (do not over tighten so as to avoid compressing the internal gears)
N.B. Position the gearmotor at the centre of the overhead door, for non-protruding overhead doors, see fig. 5/A.
2.4 INSTALLING THEDRIVING SHAFTS
1. Cut the shafts to the length (L1 - 60 mm and L2 - 60 mm) as shown in fig. 6 (L1 and L2 must not exceed 1670 mm).
2. Fix the shafts to the gearmotor shaft screwing down the dowels provided.
3. Fix shaft brackets to the overhead garage door frame using suitable self-threading screws
2.5 INSTALLING THE TELESCOPIC ARMS
1. If the overhead garage door has not been so designed, fix the top supporting brackets as shown in fig. 5 with suitable self-threading screws
(maintain the measurements given in fig. 7/A).
2. Cut both of the components of the telescopic arms, maintaining the measurements given in fig. 7/B.
3. Secure the telescopic arms to the transmission bars with the screws (M10x45) and related locking nuts. (N.B.: if the shaft support is sustain-
ing the telescopic arm pin, insert the shimring as shown in fig. 6).
Up-and-over door with folding leaves (fig. 7/C)
Installation process on double-panel door is very similar to the one used with single panel door, but:
- cut the frame in its upper part as shown in the picture;
- the rotational axis of the door opener must be, when the door is closed, approx. 8 cm below the rotational axis of the door hinges "A";
- brackets "C" must be close to the hinges "B" of the garage door.
2.6. HOW TO INSTALL ARMS BY TIGHTENING THEM (fig. 9)
1. Insert the bushing in the support
2. Insert the shaft T1 on the operator and mount the shaft support on the gate (N.B. Cut the tube to measure)
3. Insert the pivot of the straight or curved arm in the shaft by passing it through the bushing and the shaft support. The arm must be inserted
into the bushing until flush.
4. Make a through-hole on the set made by the pivot + the d10mm tube and join them through screw and nut. (N.B. For a higher durability, we
recommend to pierce and tap the thread M10 together with the tube and the pivot and then fix them by screw m10x45 + nut)
3. ADJUSTING THE LIMIT SWITCH (SPINF - SPINQRE)
For the models in the SPIN series, optimise the travel of the up-and-over door by adjusting the electrical clutch of the control unit (see instruc-
tion K996M for SPIN12 - SPIN12QR and instructions K892M for SPINF - SPINQRE).
For the SPINF and SPINQRE models, the travel of the door can be optimised by turning the limit switches (1 fig. 8) on their supporting rings (2 fig. 8).
4. MANUAL UNLOCK (fig. 10)
N.B.: The release device lever may appear to be jammed at times. This is due to the force applied by the gear motor which varies according to
the size and weight of the up-and-over door. Simply apply greater pressure to the lever to move it.
A manual release kit is available on request. This allows you to turn the handle of the up-and-over door from the outside. To mount it correctly,
nr. 1 1600 mm longitudinal frame member;
nr. 2 Bossed driving shaft;
nr. 2 M8x30 mm galvanized screw;
nr. 2 M8 low self-locking nut;
nr. 2 M10x45 mm galvanized Allen screw;
nr. 2 M10 low self-locking nut;
nr. 2 Curved telescopic arm;
nr. 2 Curved arm;
nr. 2 M8x30 mm galvanized screw;
nr. 2 M6x120 mm galvanized screw;
nr. 2 M6 low self-locking nut;
15
nr. 2 Telescopic tube for straight arm;
nr. 2 Straight arm;
nr. 2 Top supporting bracket;
nr. 2 Shaft supporting bracket;
nr. 2 flanged bush;
nr. 2 M8 low self-locking nut;
nr. 2 Top supporting bracket;
nr. 4 Ø 6x18 mm flat washers;
nr. 2 M8x10 mm pointed dowels;