ng the Control Housing
BRA‐UL‐R panel.
e predrilled. Refer
illed.
n the wiring into
12. Repeat these steps for the other leaf, if installed
ectors. Be careful
e housing! It is a
Wiring the Motor
1. Locate the stress relieving cord-grip
ws or drywall
age any wires or
2. Attach connecting nut (F) to grip body (G).
Tighten securely using finger pressure only
m Overview" for
3. Slip compression nut (H) over a length of 16/3
(16 Gauge, 3 strand) motor wire and thread wire
through the assembled cord-grip
hten securely
3 (18 Gauge,
h the
ressure only.
motor to the
ming." For
BRA‐UL‐R
rol panel
4. Tighten the compression nut (H) with finger
control panel
pressure only
control panel
20' from panel
5. Refer to Wiring Simplified for wiring from motor
to control board terminals
Installing the Limit Switches
1. Install the full cam on top of the metal shaft
•
Then install the ring cam on top of the full cam
•
Do not fully tighten the fixing screws
Fig 5. Moun�ng loca�ons
F
G
H
Fig 6. Stress relief connector
Igea Motor Installation
Specifications
1. Install the limit‐switch refernce cams as
shown in g. 3. Install the full cam on top of
the metal sha�, then install the ring cam on
top of the full cam. Do not fully �ghten the
xing screws.
2. When the door is fully open, rotate the
corresponding cam (g. 4), un�l you hear a
2. When the door
'click' indica�ng the limit switch has been
is fully open,
depressed, then lock it in posi�on by
rotate the
�ghtening the appropriate screws. Repeat for
corresponding
the fully closed posi�on. Refer to "Manual
cam (fig.
Opera�on Mode" to manually swing the door.
4), until you
3. Swing the door slowly to its open and close
hear a 'click'
posi�ons, listening to see that the 'click' of
indicating the limit switch has been depressed
the limits switch occurs where desired. Adjust
as necessary.
•
Lock it in position by tightening the appropriate
screws
•
Repeat for the fully closed position
•
Refer to "Manual Operation Mode" to manually
swing the door.
3. Swing the door slowly to its open and close
positions, listening to see that the 'click' of the
limits switch occurs where desired
Note:
That the left motor's cams (close vs open)
are inverted from those of the right motor. Adjust as
necessary
LEFT MOTOR
(viewed from inside)
Left Motor (as viewed from inside)
Stop Position
1. Install the limit‐switch refernce cams as
shown in g. 3. Install the full cam on top of
Close
10
the metal sha�, then install the ring cam on
top of the full cam. Do not fully �ghten the
Open
xing screws.
2. When the door is fully open, rotate the
corresponding cam (g. 4), un�l you hear a
'click' indica�ng the limit switch has been
Right Motor (as viewed from inside)
depressed, then lock it in posi�on by
�ghtening the appropriate screws. Repeat for
Stop Position
the fully closed posi�on. Refer to "Manual
Opera�on Mode" to manually swing the door.
11
Close
3. Swing the door slowly to its open and close
posi�ons, listening to see that the 'click' of
Open
the limits switch occurs where desired. Adjust
as necessary.
10
FULL CAM
CLOSE LIMIT CAM
OPEN LIMIT CAM
CLOSE LIMIT
SWITCH
OPEN LIMIT
SWITCH
Franklin Autoswing Installation Manual
TM
(viewed from inside)
Installa�on of Limit Switches
Cam Position
Top
© 2012 Copyright Real Carriage Door Company, Inc
FULL CAM
Bottom
Cam Position
Bottom
Top
CLOSE LIMIT CAM
OPEN LIMIT CAM
CLOSE LIMIT
SWITCH
OPEN LIMIT
SWITCH
LEFT MOTOR
(viewed from inside)
RING CAM
Fig 3. Limit Switch installa�on
OPEN LIMIT CAM
CLOSE LIMIT CAM
OPEN LIMIT
SWITCH
CLOSE LIMIT
SWITCH
RIGHT MOTOR
Fig 4. Limit Switch func�ons
RING CAM
Fig 3. Limit Switch installa�on
OPEN LIMIT CAM
CLOSE LIMIT CAM
OPEN LIMIT
SWITCH
CLOSE LIMIT
SWITCH
RIGHT MOTOR
(viewed from inside)
Fig 4. Limit Switch func�ons
© 2012 Copyright Real Carriage Door Company, Inc
Page 9
Page 9
Need help?
Do you have a question about the Franklin Autoswing and is the answer not in the manual?