Advertisement
Quick Links
Deluxe Overbed Table
Assembly, Installation and Operating Instructions
Model Nos. 6417, 6418
DEALER: These instructions MUST be given to the user of this product.
NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer for further
instruction.
To ensure the safe and proper installation of the deluxe overbed table, these instructions MUST be followed:
DO NOT use this product or any available optional equipment without first completely reading
and understanding these instructions and any additional instructional material such as owner's
manuals, service manuals or instruction sheets supplied with this product or optional equipment.
If you are unable to understand the warnings, cautions or instructions, contact a healthcare
professional, dealer or technical personnel before attempting to use this equipment - otherwise,
injury or damage may occur.
ALWAYS check the overbed table for proper tightness before using.
The deluxe overbed table has a weight limitation of 25 lbs.
Invacare products are specifically designed and manufactured for use in conjunction with
Invacare accessories. Accessories designed by other manufacturers have not been tested by
Invacare and are not recommended for use with Invacare products.
After any adjustments, repair or service and before use, make sure that all attaching component
parts are secure.
Assembling/Disassembling
Model 6417
NOTE: For this procedure, refer to FIGURE 1 on page 2.
1.
Place table top on floor with mounting holes facing up.
2.
Secure the mast to the table top with six mounting
screws. Tighten securely.
3.
Secure the base to the mast with the two bolts, washers,
and inserts. Tighten securely.
4.
Install the four casters into the four holes provided in
the base.
5.
Place the overbed table to the upright position.
6.
To disassemble, reverse STEPS 1‐5.
For more information regarding Invacare products, parts, and services, please visit www.invacare.com
Part No 1143201
SAVE THESE INSTRUCTIONS
Safety Summary
WARNING
ACCESSORIES WARNING
INSTALLATION WARNING
1
Model 6418
NOTE: For this procedure, refer to FIGURE 1 on page 2.
1.
Place the tilt table top on the floor with supporting
bracket facing up.
2.
Secure the mast to the supporting bracket with the bolt,
washer, and nut. Tighten securely.
3.
Secure the base to the mast with the two bolts, washers,
and inserts. Tighten securely.
4.
Install the four casters into the four holes provided in
the base.
5.
Place the overbed table to the upright position.
6.
To disassemble, reverse STEPS 1‐5
Deluxe Overbed Table
Advertisement
Related Manuals for Invacare 6417
Summary of Contents for Invacare 6417
-
Page 1: Safety Summary
The deluxe overbed table has a weight limitation of 25 lbs. ACCESSORIES WARNING Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products. - Page 2 Base Base Mast Mounting Screws Casters Casters Model 6418 Bolt Washer Table Top Model 6417 Tilt Table Top Supporting Mounting Bracket Holes FIGURE 1 Assembling/Disassembling Operating the Overbed Table NOTE: For this procedure, refer to FIGURE 2 on page 3. Adjusting Table Height WARNING ALWAYS check to ensure latching mechanism/height adjustment lever, located underneath the table top, is properly engaged prior to use.
- Page 3 Angle Adjustment Lever (Model 6418 only) Transport Screw Latching Mechanism/ Height Adjustable Lever NOTE: Only Model 6418 is shown. FIGURE 2 Adjusting Table Height - Adjusting Table Angle Transporting CAUTION Before taking the overbed table apart, adjust the table top to the lowest position and replace the transport screw so the mast is locked in place before being packed and shipped otherwise dam- age may result.
-
Page 4: Limited Warranty
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants its product to be free from defects in materials and workmanship for one year for the original purchaser. If within such warranty period any such product shall be proven to be defective, such product shall be repaired or replaced, at Invacare's option with refurbished or new parts.