Bluetooth Function; Listening To The Radio - AEG KRC 4361 BT Instruction Manual

English
36
5. Press the TIME SET/COOK TIMER button for confirma-
tion. The minute indicator will flash on the display.
6. Adjust the setting with the SKIP+/SKIP- buttons (7/8).
7. Save the time setting by pressing the TIME SET/COOK
TIMER button again.
Adjusting the Volume
Use the VOL+/VOL- buttons (9) to adjust the volume.
Display Brightness
You can use the SNOOZE/DIMMER button (15) to adjust the
brightness of the display and of the light strip beneath the
operating keys.

Listening to the Radio

Scanning stations
1. Use the /FUNC. button (10) to select the radio mode.
2. Tune the desired stations with the SKIP+ (7) and SKIP- (8)
buttons. When holding down either of the buttons, the
device will start scanning until the next radio station is
found. The display will show the respective frequency.
3. If there is interference on the received station, try to
improve the reception by rotating, winding or unwinding
the wire antenna.
Presetting Radio Stations
The device can preset up to 30 radio stations. To preset a
station, follow the steps below:
1. Search for a station as described in "Scanning stations".
2. Press the ANSWER/PROG/AMS button (6). The display
will show PROGRAM and the respective preset location
will begin to flash.
3. Use the PRE.+/ALARM 2 (12) and PRE.-/ALARM 1 (13)
buttons to choose the preset location for the correspond-
ing station.
4. Press the ANSWER/PROG/AMS button again. The
station will be preset. The PROGRAM indicator and the
preset location will disappear.
Recalling Preset Radio Stations
Use the PRE+/ALARM 2 (12) and PRE-/ALARM 1 (13) buttons
to select the memory locations.
Automatic station scan
Important! Any previously stored radio stations will be over-
written.
When holding down the ANSWER/PROG/AMS button (6) for
approx. 3 seconds, the device will start the automatic station
scan searching the entire frequency range automatically
for stations. The stations found will be stored on the preset
locations 1-30 in ascending order.
NOTE:
The order cannot be changed once set.

Bluetooth Function

Bluetooth involves a technology for wireless radio connec-
tion of devices over a short distance. Devices with Bluetooth
standard are transmitting between 2.402 and 2.480 GHz in
the ISM band (Industrial, Scientific and Medical). Interference
can be caused for example by WLAN-networks, DAB radios,
cordless phones, or microwave ovens which work on the
same frequency band.
This device offers you the possibility to use a Bluetooth-ena-
bled device. The functional radius is limited to approx.
15 metres depending on the surroundings and the unit used.
If your playing device supports the A2DP profile (Advanced
Audio Distribution Profile) and has a music-player function,
then you can also wirelessly transfer music to the device. The
A2DP profile involves a multi-vendor Bluetooth profile. By
streaming, stereo-audio signals are wirelessly transferred be-
tween the playing device (source) and the receiving device.
To be able to remotely control the source, the playback de-
vice must support the AVRCP profile (Audio Video Remote
Control Profile).
Due to the different device manufacturers, models, and
software versions, a full functionality cannot be guaranteed.
Logging on Devices (Pairing)
Before you listen to music via the unit, you must pair the
devices.
1. Ensure, that the Bluetooth function is activated in your
player (e.g. mobile phone). For this, refer to the operation
manual of your player.
2. Press the /FUNC button (10) repeatedly, until "bt" is
shown on the display. The BT indicator light (5) blinks.
This signalizes that the device is in pairing mode.
3. Choose the Bluetooth menu in your player and register
the device in your player. For this, refer to the operation
manual of your player. The device "KRC 4361 BT" will
show in your player as a selection.
NOTE:
Only one playback device may be connected to the
device at one time. If the device is already connected
to another playback device, then the device will not
appear in the BT selection menu.
4. Now enter the password "0000" in your player, depend-
ing on the device manufacturers, model, and software
version.
If the pairing was done successfully, a beeping sound can
be heard and the BT indicator light will be lit. For the further
procedure, please refer to the user manual of the playback
unit. If possible, adjust the volume of the external unit to a
comfortable level.