Advertisement
Quick Links
Sun Ultra™ 10 EMI Retrofit Guide
Includes New CD-ROM Cable
Installation Instructions for
Cable Kit F370-3267-03
Sun Microsystems, Inc.
4150 Network Circle
Santa Clara, CA 95054 U.S.A.
650-960-1300
Part No. 816-2780-11
May 2002, Revision A
Send comments about this document to: docfeedback@sun.com
Advertisement
Related Manuals for Sun Microsystems Ultra 10 EMI
Summary of Contents for Sun Microsystems Ultra 10 EMI
- Page 1 Sun Ultra™ 10 EMI Retrofit Guide Includes New CD-ROM Cable Installation Instructions for Cable Kit F370-3267-03 Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. 650-960-1300 Part No. 816-2780-11 May 2002, Revision A Send comments about this document to: docfeedback@sun.com...
- Page 2 Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd. Sun, Sun Microsystems, le logo Sun, Ultra, et Solaris sont des marques de fabrique ou des marques déposées, ou marques de service, de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc.
-
Page 3: Package Contents
Note – If you are replacing the CD-ROM cable as part of the F370-3267-03 cable kit, go to “Installing the New CD-ROM Drive Cable” on page 8. The Sun Ultra 10 EMI Retrofit Guide describes how to reduce electromagnetic interference (EMI) emitted by the Ultra™ 10 system. - Page 4 The service manual is available online from the following sources: Sun Ultra 10 Software Supplement CD-ROM that ships with the system http://docs.sun.com http://www.sun.com/products-n-solutions/hardware/docs Sun Ultra 10 EMI Retrofit Guide • May 2002...
- Page 5 For this procedure, refer to FIGURE 2 1. Locate the TPE connector on the Ultra 10 motherboard. The connector is located at the rear corner of the system case. TPE Connector and Clip Installation FIGURE 2 Sun Ultra 10 EMI Retrofit Guide...
- Page 6 FIGURE 3 Disk Drive EMI Clip FIGURE 3 Note – If your system only has one clip, install two more clips. If your system has two clips, install the third clip. Sun Ultra 10 EMI Retrofit Guide • May 2002...
- Page 7 To Install the Disk Drive EMI Clips 1. Disconnect the power, drive, and audio cables from the rear of the floppy drive and CD-ROM drive. FIGURE 4 Disconnecting the Floppy Drive and CD-ROM Drive Cables FIGURE 4 Sun Ultra 10 EMI Retrofit Guide...
- Page 8 Screw Removing the CD-ROM Drive and Floppy Drive Bracket FIGURE 5 3. Slide the CD-ROM drive and floppy drive bracket out of the chassis. . Set the drives aside. FIGURE 5 Sun Ultra 10 EMI Retrofit Guide • May 2002...
- Page 9 6. Reattach all the cables you disconnected in Step 1, except for the CD-ROM drive cable. 7. Disconnect the other end of the CD-ROM drive cable from the motherboard at connector J14. Discard this cable. Sun Ultra 10 EMI Retrofit Guide...
- Page 10 Replacement CD-ROM Drive Cable FIGURE 7 Note – Do not separate the dual lock fasteners or remove the adhesive backing from the fasteners as this time. You perform this task later in the procedure. Sun Ultra 10 EMI Retrofit Guide • May 2002...
- Page 11 3. Peel the adhesive backing from the dual lock fasteners. 4. Align the left edge of the ferrite filter with the CD-ROM drive cable connector. 5. Press the sticky side of the dual lock fasteners to where you cleaned the chassis. Press firmly. Sun Ultra 10 EMI Retrofit Guide...
- Page 12 Procedures”, of the Sun Ultra 10 Service Manual, 805-7764. The chapter describes how to remove the antistatic wrist strap, replace the system cover and peripheral cables, and power on the system. Sun Ultra 10 EMI Retrofit Guide • May 2002...