Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Federal Signal Corporation VIPER EXT
Summary of Contents for Federal Signal Corporation VIPER EXT
- Page 1 ™ IPER Installation Manual 2562387B REV. B 1008 Printed in U.S.A.
- Page 2 EXT, I , and I are trademarks of Federal Signal Corporation. IPER MPAXX NTELLI LASH is a registered trademarks of Federal Signal Corporation. OLARIS Plexus is a registered trademark of BTI Chemical Company Inc.
-
Page 3: Table Of Contents
Contents Safety Message to Installers and Service Personnel of Warning Light Equipment ....................1 Safety Message to Operators of Warning Light Equipment ....4 Unpacking Your Shipment ..............5 An Overview of the V EXT Series LED Light Heads ...... 5 IPER Installing the V EXT Series LED Light Heads ......... - Page 4 Contents...
-
Page 5: Safety Message To Installers And Service Personnel Of Warning Light Equipment
Safety Message to Installers and Service Personnel of Warning Light Equipment Safety Message to Installers and Service Personnel of Warning Light Equipment People’s lives depend on your proper installation and servicing of Federal Signal products. It is important to read and follow all instructions shipped with this product. - Page 6 Safety Message to Installers and Service Personnel of Warning Light Equipment and fuses are rated correctly to handle the device and system amperage for proper operation after installation. dling any components of the system. when handling these components. system. Placing the antenna too close to the lighting system could cause Mounting the antenna too close to the lighting system may also cause the radio noise emitted from the lighting system to interfere with the reception of the radio transmitter and reduce radio reception.
- Page 7 Safety Message to Installers and Service Personnel of Warning Light Equipment glass portion is touched during installation. Use gloves when handling carefully with isopropyl alcohol. cal or mechanical damage to the vehicle. a vehicle with a magnetically mounted warning light installed. The light the user.
-
Page 8: Safety Message To Operators Of Warning Light Equipment
Safety Message to Operators of Warning Light Equipment tions to instructional staff and all operating personnel. and/or re-installing the product. Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death to you or others. RETAIN AND REFER TO THIS MESSAGE Safety Message to Operators of Warning Light Equipment People’s lives depend on your safe use of our products. -
Page 9: Unpacking Your Shipment
An Overview of the Viper EXT Series LED Light Heads foreign particles that prevent good surface contact. tops. Failure to follow these safety instructions and precautions may result in property damage, serious injury, or death to you, to passengers, and to others. -
Page 10: Installing The Viper Ext Series Led Light Heads
Installing the Viper EXT Series LED Light Heads IPER ™ warning lights. The V MPAXX IPER Table 1 migrate in and out of synchronization. EXT models are designed for use with all Federal Signal switch con- IPER trollers. The V... -
Page 11: Mounting The V
Installing the Viper EXT Series LED Light Heads than the LED color will greatly reduce the light output and reduce the ef- fectiveness of the light for emergency signaling purposes. Failure to follow this warning may result in personal injury or death to you or others. - Page 12 Installing the Viper EXT Series LED Light Heads AIRBAG DEPLOYMENT Do not install equipment or route wiring in the deployment path of an airbag. Failure to observe this warning will reduce the effectiveness of the air bag, or potentially dislodge the equipment, causing serious injury to you or others.
-
Page 13: Mounting The V Iper Ext To A Vehicle From The Back
Installing the Viper EXT Series LED Light Heads 7. Route the wires from the module through the hole in the gasket and mount- Figure 1 GASKET EXT LED IPER LIGHT HEAD #10 SCREWS MOUNTING BEZEL Figure 1: Mounting the V... - Page 14 Installing the Viper EXT Series LED Light Heads AIRBAG DEPLOYMENT Do not install equipment or route wiring in the deployment path of an airbag. Failure to observe this warning will reduce the effectiveness of the air bag, or potentially dislodge the equipment, causing serious injury to you or others.
-
Page 15: Wiring The V Iper Ext In The Vehicle
Installing the Viper EXT Series LED Light Heads 7. Route the wires from the module through the hole in the mounting surface Figure 2 EXT LED IPER LIGHT HEAD #8 SCREWS MOUNTING SURFACE Figure 2: Mounting the V EXT from the rear IPER mounting surface with the sheet-metal screws provided. - Page 16 Installing the Viper EXT Series LED Light Heads FUSE ELECTRICAL SOURCES Always fuse current/voltage sources with a fuse connected near the power source. Be sure that the fuse is properly rated to protect the electrical load, the wiring and the connectors used in the circuit.
-
Page 17: Selecting A Flash Pattern
Maintaining the Viper EXT Series LED Light Heads Selecting a Flash Pattern 1. Touch and remove the white pattern-selection wire from the controller tern you want. Table1: Flash patterns for V EXT Series LED Light Heads IPER Flash Flash Description... -
Page 18: Maintaining The V Iper
Maintaining the Viper EXT Series LED Light Heads Maintaining the V EXT Series LED Light Heads IPER Periodically cleaning the V EXT lenses using proper procedures and compat- IPER you can order replacements for mounting hardware. Cleaning the Light Heads CRAZING/CHEMICALS Crazed, cracked or faded domes or reflectors reduce the light output and... -
Page 19: Replacing The Mounting Hardware
Maintaining the Viper EXT Series LED Light Heads Replacing the Mounting Hardware Table 2: V EXT replacement parts IPER Description Part Number Mounting Bezel, V 8613147 IPER Mounting Gasket, V 8613148 IPER Screws, Bezel, #10 7011182A-12 Screws, w/o Bezel 7011193-06... - Page 20 © www.fedsig.com...