STI -1215 Manual

EXISTING
WARNING
APPLIANCE
RAWL PLUG
(4) PROVIDED
ADHESIVE BACKED GASKET
SPACER TO MOUNTING SURFACE
01212 SPACER

INSTALLATION NOTES

1. To minimize strobe light loss, regardless of the type of horn/strobe appliance used, the clear
section (not the section containing the cutout slots) must be centered over the strobe light
lens. Failure to follow these instructions may lead to light loss transmission.
2. Stopper Dome must be installed to comply with applicable NEC, NFPA and local codes.
3. Stopper Dome may be installed outdoors when appliance carries an outdoor rating.
4. If added protection is needed due to environmental conditions, order SUB-123 Enviro kit.
REMARQUES SUR L'INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type d' a larme sonore/de
stroboscope utilisé, la section dégagée (et NON la section contenant les fentes de découpe), doit
être centrée sur l' o bjectif stroboscopique. Le fait d' o mettre ces instructions risque d' e ntraîner la
perte de di usion de la lumière.
2. Le dôme Stopper doit être installé de sorte à être conforme avec les normes NEC, NFPA applicables
et les codes locaux.
3. Il est possible d'installer un dôme Stopper à l' e xtérieur lorsque l' a ppareil est homologué pour
utilisation à l' e xtérieur.
4. S'il est nécessaire d' a jouter une autre protection en raison des conditions environnementales,
commandez la trousse Enviro, SUB-123.
INSTALLATION OF STI-1217 STOPPER DOME FOR HORN/SPEAKER/STROBE
All specifications and information shown were current as of publication and are subject to change without notice.
USA - Headquarters
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: info@sti-usa.com
Web: www.sti-usa.com
CONDUIT SEALING GASKET
SUB-123 ENVIRO KIT PLASTIC INSERT
(1) PROVIDED
SCREW
#10 x 1-1/2 in.
(4) PROVIDED
GASKET
(COVER TO SPACER)
01215 HORN/STROBE
PROTECTIVE COVER
WASHER (6) PROVIDED
#8 - 32 x 3/8 in.
SOCKET HEAD CAP SCREW
European Office
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: 44 (0) 1527 520 999 Fax: 44 (0) 1527 501 999
E-mail: info@sti-emea.com • Web: www.sti-emea.com
STI-1215
COVER
STI-1212
7.37 in.(187mm)
SPACER
7.87 in.(200mm)

PRODUCT DIMENSIONS

IF ADDED PROTECTION IS NEEDED
DUE TO ENVIROMENTAL CONDITIONS
ORDER SUB-123 ENVIRO KIT
ALSO INCLUDES (6)
#8-32 X 3/4 in. SOCKET CAP SCREWS
(6) PROVIDED
Three year warranty or a one year limited warranty (from
date of purchase) on most products. See website for details.
Electronic warranty form at www.sti-usa.com/wc14.
2.87 in.(73mm)
1.62 in.(41mm)

INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW

1. Using enclosure assembly as a template, place against
mounting surface at proper location according to NFPA 72.
2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 in.
(25mm) deep.
3. Insert the (4) rawl plugs into the wall.
4. Mount frame assembly to wall with screws.
5. Install electrical fittings as needed.
6. Install horn/strobe appliance (except for retrofit applications).
7. Install cover with clips and screws.
8. Test appliance according to appliance manufacturer's
instructions.

CLEANING INSTRUCTIONS

Rinse with water to remove abrasive dust and dirt. Wash with soap
or mild detergent, using a soft cloth (do not scrub). Rinse once
more then dry with a soft cloth or chamois. To remove grease or
wet paint, rub gently with a cloth wetted with naphtha. Then wash
and rinse. DO NOT USE RAZOR BLADES.
1217IS JAN2017