Connection Valve Assembly; Pool Maintenance - Bestway OVAL FAST SET Owner's Manual

Hide thumbs

Table Of Contents

Table of Contents

Available languages

Connection Valve Assembly

For 732cm x 366cm x 122cm (24' x 12' x 48") and 853cm x 366cm x 122cm (28' x 12' x 48") models

1. Screw the Debris Screen (P6168) onto the Connector (P6167). (See Fig.5)

2. From inside the pool, insert this assembled Unit to the pool's inlet A and outlet B. (See Fig.6)

NOTE: Ensure the Gasket (P6166) is properly in place on the assembled Unit inside of the pool liner.

3. From outside of the pool, tighten the Connector Nut (P6165) onto the assembled Unit by the Wrench (P6169). (See Fig.7).

4. Hand-tighten the Control Valve (P6162) to the assembled Unit. (See Fig.8)

NOTE: Check that both the Control Valve Gasket (P6164) and O-ring (P6163) are correctly positioned on the Control Valve.

5. Refer to the pool manual for the rest of the pool installation.

OPERATION NOTE: Use the control screw on top of the Control Valve to open and close the Valve. (See Fig.9)

6. Make sure the valve is closed.

Fig. 4

Filling Pool with Water

ATTENTION: Do not leave pool unattended while filling with water

Pool walls will rise as you fill with water. (See Fig. 10)

The pool liner must extend evenly around the outside of the inflatable ring when filling the pool with water.

1. Fill pool to drain valve.

STOP

2. Turn water off. Check that the water is not collecting on any side to ensure the pool is level. If pool is

not level, drain water and re-level ground by digging out. (See Fig. 12) Never attempt to move the pool with water

in it, serious personal injury or damage to the pool may result.

NOTE: Your pool may contain up to xxxxx liters / xxxx gallons which equals xxxxx pounds of pressure.

If your pool has any bulge or uneven side then the pool is not level, the sides may burst and the water

may discharge suddenly causing serious personal injury and/or damage to property.

3. Fill pool to lowest pump valve.

STOP

4. Turn water off. Check valves for secure fit.

5. Fill pool until water capacity is 80%, up to the bottom of the inflated ring of the pool so that the sides are smooth and firm. (See Fig. 11)

DO NOT OVERFILL as this could cause the pool to collapse. In times of heavy rainfall you may need to empty some of the water to ensure the level

is correct.

6. Check pool for any leaks at valves or seams, check ground cloth for any evident water loss. Do not add chemicals until this has been done.

7. In the event of a leak, patch your pool using the patch kit provided. Refer to the FAQ's for further information.

Fig. 10

Pool Maintenance

If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your children.

NOTE: The filter pump is used to circulate the water and to filter small particles to keep your water free of suspended dirt particles. In order to keep

your pool water clean and hygienic you must add chemicals.

To keep your pool clean:

1. Contact your local pool supply shop for advice and purchase of chemicals and PH kits. One of the most important factors to increase the life of the

liner is to keep continuosly clean and healthy water. Please follow strictly the instructions from professional technicians for the water treatment

through the use of chemicals.

2. Locate a bucket of water next to pool to clean users' feet before entering pool.

3. Cover the pool when not in use.

4. Skim pool regularly to avoid settled dirt.

5. Change filter cartridge in filter pump every 2 weeks.

6. Gently clean any scum from below the top ring with a clean cloth.

7. To improve the water quality we suggest to use Bestway accessories like skimmer, maintenance kits.

Please visit our website www.bestway-service.com or contact your pool supplier.

Please be careful in case of rain water, kindly check that the water level is not higher than the expected one. If so, please act consequently.

Proper maintenance can maximize the life of your pool.

ATTENTION: Do not use pump when pool is in use.