Related Manuals for SenTech STC-CMB401ACXP
Summary of Contents for SenTech STC-CMB401ACXP
- Page 1 No. 16S001-ES01 4 Meg CMOS Monochrome CoaXPress Camera STC-CMB401ACXP (4M Monochrome) Product Specifications and Users guide Sentech Co., Ltd STC-CMB401ACXP Specifications and Users guide...
-
Page 2: Table Of Contents
..................................4 EATURES ................................4 AMING ETHOD SPECIFICATIONS ..............................5 ........5 LECTRONIC SPECIFICATIONS ECHANICAL SPECIFICATIONS NVIRONMENTAL SPECIFICATIONS 2.1.1 STC-CMB401ACXP ............................5 ........................6 PECTRAL ENSITIVITY HARACTERISTICS 2.2.1 STC-CMB401ACXP ............................6 IO C ................................7 ONNECTOR 2.3.1 Pin assignment ..............................7 2.3.2... - Page 3 The camera is a general-purpose electronic device; using the camera for the equipment that may threaten human life or cause dangers to human bodies directly in case of failure or malfunction of the camera is not guaranteed. Use the camera for special purposes at your own risk. STC-CMB401ACXP Specifications and Users guide...
-
Page 4: Overview
No. 16S001-ES01 Overview This document describes the specifications of the following cameras STC-CMB401ACXP (4M Monochrome) 1.1 Features CMOS Sensor (Global Shutter) CoaXPress (later CXP) Interface Maximum 142.5 fps on 4M pixel(8bit) 1.2 Naming Method STC-CMx401CXP-x CXP: CoaXPress Sensor Size 1: 1”... -
Page 5: Specifications
No. 16S001-ES01 Specifications 2.1 Electronic specifications / Mechanical specifications / Environmental specifications 2.1.1 STC-CMB401ACXP Table 1. Specifications Product STC-CMB401ACXP 1” Type 4Meg monochrome progressive CMOS Electronic Imager specifications (CMOSIS: CMV4000) Shutter Global Shutter Active picture elements 2048 (H) x 2048 (V) Chip size 22.5 ×... -
Page 6: Spectral Sensitivity Characteristics
No. 16S001-ES01 2.2 Spectral Sensitivity Characteristics 2.2.1 STC-CMB401ACXP Figure 2. Spectral Sensitivity Characteristics STC-CMB401ACXP Specifications and Users guide... -
Page 7: Io Connector
Less than+1.00V +3.00 to +24V 4uA(typ.) Input Output 0 to +2.20V +3.00 to +24V 15mA (Max.) N.C. N.C. *1) These values on the table are just reference number, please evaluate carefully when these IO are used. STC-CMB401ACXP Specifications and Users guide... -
Page 8: Default Setting Of Input Output
This function can set high or low level and the user can use this to check the status on the software. 3) Trigger Input This function is used for the trigger signal in the edge preset mode. Input Response Characteristics STC-CMB401ACXP Specifications and Users guide... -
Page 9: Gpio Circuit (Output)
6) Frame End This function outputs when exposure ended with the with pulse delay setting and pulse duration applied. 8) Exposure Active This function outputs the High or Low signal while in actual exposure time. STC-CMB401ACXP Specifications and Users guide... -
Page 10: General Purpose Output (Reference 2)
No. 16S001-ES01 General Purpose Output ( Reference General Purpose Output ( Reference Characteristics of the output signals STC-CMB401ACXP Specifications and Users guide... -
Page 11: Conector Indicator Lamp
Device / Host connected, waiting for event Slow pulse orange (e.g. trigger, exposure pulse) Device / Host connected, data being transferred Fast flash green. Data Transfer Error Red LED ON (500msec) System Error Red LED flicker fast STC-CMB401ACXP Specifications and Users guide... -
Page 12: Dimensions
No. 16S001-ES01 Dimensions unit: mm STC-CMB401ACXP Specifications and Users guide... -
Page 13: Camera Operation
The parameter sets it in % for the ExposureTime HDRVlow1 Set the voltage of HDRVlow1 for the HDR saturation level HDRVlow2 Set the voltage of HDRVlow2 for the HDR saturation level Cxp Link Configuration CXP6_X1 STC-CMB401ACXP Specifications and Users guide... - Page 14 Save the User Set specified by UserSetSelector to the non-volatile UserSetSave memory of the device Selects the feature User Set to load and make active by default when UserSetDefault the device is reset STC-CMB401ACXP Specifications and Users guide...
-
Page 15: Saving And Loading A Data
RAM into memory area that was Register selected on UserSetSelector. EEPROM Note: UserSetSave is not available Default Selector when Default on UserSetSelector was selected UserSetSelector Setting Procedure 1. Set UserSet1 on the UserSetSelector 2. Execute UserSetSave STC-CMB401ACXP Specifications and Users guide... -
Page 16: Load Setting
4.2.4 Camera initialization In order to initialize camera setting, please follow the procedure as bellow. Write Defalut into UserSet1. Setting Procedure 1. Set Default on UserSetSelector 2. Execute UserSetLoad 3. Set UserSet1 on UserSetSelector 4. Execute UserSetSave STC-CMB401ACXP Specifications and Users guide... - Page 17 Valid Line Number is calculated from as following formura. 38 /129 / (Vertical AOI Valid Line Number + 18 ) x 1,000,000 [fps] *Vertical AOI Valid Line Number: 2Line unit (Minimum: 2 Line) *Horizontal pixel number does not make effect framerate. STC-CMB401ACXP Specifications and Users guide...
-
Page 18: Revision History
No. 16S001-ES01 Revision History Date Changes Note ES00 2016/01/05 Released: Sample model ES01 2016/03/16 Revised: Dimensions(C-Mount) STC-CMB401ACXP Specifications and Users guide... - Page 19 No. 16S001-ES01 7F, Harada center building 9-17, Naka cho 4 chome Atsugi-city, Kanagawa 243-0018 Japan Sentech Co., Ltd TEL +81-46-295-7061 FAX +81-46-295-7066 URL http://www.sentech.co.jp/ STC-CMB401ACXP Specifications and Users guide...
Need help?
Do you have a question about the STC-CMB401ACXP and is the answer not in the manual?
Questions and answers