During Use - ubbink Control Unit Manual

• The Control unit may not be covered, for example,
by a curtain or a cabinet;
• Consult paragraph
requirements.

2.3 During use

Take note! Settings, which have not been described
in this user's manual, are intended for installers appro-
ved by Ubbink. Do not change these by yourself.
2.4 During maintenance
Careful! Clean the screen with a soft cloth.
Careful! Never apply water and/or (cleaning) liquid to
the screen.
2.5 For the environment
Take note! The Control unit may not be removed
as unsorted urban waste, but should be treated
separately.
Take note! Make enquiries within your own region,
where the Control unit can be handed in when use has
been terminated. Do not throw away electrical devices
or parts, but check if (parts of) the Control unit cannot
be handed in, recycled or re-used.
3 Assembly and installation (to be performed
by the installer)
Assembly and installation should be performed by an installer
approved by Ubbink.
3.1 Assembly
You should perform the steps, described in paragraph 3.1.1
through paragraph 3.1.4, one by one, to assemble the Control
unit.
3.1.1 Disconnecting the operational module from the wall
bracket
Disconnect the operational module from the wall bracket.
Perform the following actions
• Slide the Control unit upward over the two guide profiles
of the wall bracket until the Control unit can be taken off.
3.1.2 Electrical connection
The following actions should be performed to connect the
Control unit electrically (see
• Feed the two-core wire (from the device to be connected)
through via opening at the back of the wall bracket.
• Check that the cables' ends have been stripped in the
correct manner. If this is not the case, do so.
• Screw the cable to the terminal No. 1 and No. 2. Consult
the installation instructions of the device to be connected,
for more information on the correct connection.
3.1.3 Mounting the wall bracket
The wall bracket can be attached to a wall box (Ø 55 mm) or
can be directly mounted on the wall with screws and plugs.
1.2 for environmental
4
:
):
5
• Screw the wall bracket onto the wall in the correct posi-
tion. Here one must use the mounting holes in the wall
bracket (see ).
6
Take note! Consult paragraph 2.2 for more informa-
tion on placing the Control unit.
3.1.4 Replacing the operational module in the wall bracket
Place the operational in the wall bracket mounted on the wall.
Perform the following actions for this (see
• Slide the Control unit downward over the two guide pro-
files. Make sure the guide profiles of the wall bracket fit
snugly in the cutouts of the Control unit provided for that
purpose.
Take note! The operational module should click onto
the wall bracket. Only then is a proper electrical con-
nection established.
3.2 Installation
3.2.1 Setting language
You can set the language in which the menus are presented.
Perform the following actions to set the language(see
& ):
12
• Press return as many times as necessary to get to the
2
main screen
• Press . 'Main Menu' opens
1
• Select 'Basic Settings' by turning
• Press . 'Basic Settings' opens
1
• Select 'Language' by turning
• Press . 'Language' opens
1
• Select the desired language by turning
• Press to set the selected language
1
• Press return as many times as necessary to get to the
2
main screen
Take note! The names of the described menu items
will not correspond with this user manual's menu items
if the Control unit is set to a language other than Dutch.
3.2.2 Setting time
You can set the time. The time is visible on the main screen
The Control unit only has 24 hour representation. Perform the
following actions to set the time (see
• Press return as many times as necessary to get to the
2
main screen
• Press . 'Main Menu' opens
1
• Select 'Basic Settings' by turning
• Press . 'Basic Settings' opens
1
• Select 'Clock' by turning
• Press . 'Clock' opens
1
• Change the time by turning
• Press to confirm the time
1
• Repeat the previous two steps for both the minutes and
seconds
• Press return as many times as necessary to get to the
2
main screen
3.2.3 Setting date
You can set the date. The date is visible on the main screen.
Perform the following actions to set the date(see
• Press return as many times as necessary to get to the
2
7
):
1
1
1
1
1 ):
1
1
1
&
1 ,
9
,
9
):
12
9