Page 1: Table Of Contents
RKC INSTRUMENT INC. Temperature Driver Controller System Configuration....................... 3 Selection of External Device ..................11 Example of Communication Setting ................12 Setup Items ........................104 Cable Diagram ......................109 Supported Device......................213 Device Code and Address Code.................. 288 Error Messages......................294...
Page 2 Temperature Controller Driver Introduction This manual describes how to connect the Display and the External Device (target PLC). In this manual, the connection procedure will be described by following the below sections: System Configuration  "1 System Configuration" (page 3) This section shows the types of External Devices which can be connected and SIO type.
Page 3 Temperature Controller Driver System Configuration The system configuration in the case when the External Device of RKC INSTRUMENT INC. and the Display are connected is shown. Setting Cable Series Link I/F SIO Type Example Diagram CB100-*-5/ CB400-*-5/ Setting Cable Terminal Block on RS422/485 CB500-*-5/...
Page 4 Temperature Controller Driver Setting Cable Series Link I/F SIO Type Example Diagram HA900---*-1-// HA900---*-1-// HA901---*-1-// HA901---*-1-// Setting Cable HA400---*-1-// Terminal Block on RS232C Example 5 Diagram 2 HA400---*-1-// the controller. (page 20) (page 117) HA401---*-1-// HA401---*-1-// HA930---*-1-/ HA430---*-1-/ HA900---*-5-// HA900---*-5-// HA901---*-5-//...
Page 5 Temperature Controller Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable Modular connector H-PCP--1N-* RS232C Example 38 Diagram 11 SR Mini 1 on the controller. (page 86) (page 179) (H-PCP- Setting Cable Modular connector RS422/485 A/B) H-PCP--4N-* Example 39 Diagram 8 on the controller.
Page 6 Temperature Controller Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable Terminal Block on G9-*--1/A RS232C Example 26 Diagram 2 the controller. (page 62) (page 117) Setting Cable Terminal Block on RS422/485 REX-G9 G9-*--4/A Example 27 Diagram 10 the controller.
Page 7 Temperature Controller Driver Setting Cable Series Link I/F SIO Type Example Diagram Z-TIO-A-/- Setting Cable Z-TIO-B-/N- Terminal Block on RS422/485 Example 40 Diagram 13 (Z-TIO) Z-TIO-C-/- the controller. (2 wire) (page 90) (page 183) Z-TIO-D-/N- Setting Cable Z-DIO-A-/- Terminal Block on RS422/485 Example 41 Diagram 13...
Page 8 Temperature Controller Driver  Connection Configuration • 1:1 Connection Display External Drive • 1:n Connection External External External Drive Drive Drive Display Maximum number of connections: 16 units • 1:n Connection (For the SRZ (Z-TIO), SRZ (Z-DIO), and SRZ (Z-CT) Series) Display External Drive Maximum number of connections: 16 units...
Page 9 Temperature Controller Driver  IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details. Usable port Usable Port Series RS-232C RS-422/485(4 wire) RS-422/485(2 wire) COM1 , COM2,...
Page 10 Temperature Controller Driver DIP Switch setting: RS-422/485 (4 wire) DIP Switch Setting Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD) data: Always output Terminal resistance (220) insertion to SD (TXD): None Terminal resistance (220) insertion to RD (RXD): None Short-circuit of SDA (TXA) and RDA (RXA): Not available Short-circuit of SDB (TXB) and RDB (RXB): Not available RS (RTS) Auto control mode: Disabled...
Page 11: System Configuration
Temperature Controller Driver Selection of External Device Select the External Device to be connected to the Display. Setup Items Setup Description Number of Devices/ Use an integer from 1 to 4 to enter the number of Devices/PLCs to connect to the Display. PLCs Select the manufacturer of the External Device to be connected.
Page 12: Example Of Communication Setting
Temperature Controller Driver Example of Communication Setting Examples of communication settings of the Display and the External Device, recommended by Pro-face, are shown. Setting Example 1  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. •...
Page 13 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 14 Temperature Controller Driver Setting Example 2  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 15 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 16 Temperature Controller Driver Setting Example 3  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 17 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 18 Temperature Controller Driver Setting Example 4  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 19 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 20 Temperature Controller Driver Setting Example 5  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 21 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 22 Temperature Controller Driver Setting Example 6  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 23 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 24 Temperature Controller Driver Setting Example 7  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 25 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 26 Temperature Controller Driver Setting Example 8  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 27 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 28 Temperature Controller Driver Setting Example 9  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 29 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 30 Temperature Controller Driver 3.10 Setting Example 10  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 31 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 32 Temperature Controller Driver 3.11 Setting Example 11  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 33 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 34 Temperature Controller Driver 3.12 Setting Example 12  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 35 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 36 Temperature Controller Driver 3.13 Setting Example 13  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 37 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 38 Temperature Controller Driver 3.14 Setting Example 14  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 39 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the rotary switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 40 Temperature Controller Driver 3.15 Setting Example 15  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 41 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the rotary switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 42 Temperature Controller Driver 3.16 Setting Example 16  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 43 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 44 Temperature Controller Driver 3.17 Setting Example 17  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 45 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, Shift, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 46 Temperature Controller Driver 3.18 Setting Example 18  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 47 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MONI/MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 48 Temperature Controller Driver 3.19 Setting Example 19  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 49 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MONI/MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 50 Temperature Controller Driver 3.20 Setting Example 20  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 51 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the rotary switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 52 Temperature Controller Driver 3.21 Setting Example 21  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 53 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the rotary switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 54 Temperature Controller Driver 3.22 Setting Example 22  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 55 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the rotary switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 56 Temperature Controller Driver 3.23 Setting Example 23  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 57 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 58 Temperature Controller Driver 3.24 Setting Example 24  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 59 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 60 Temperature Controller Driver 3.25 Setting Example 25  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 61 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 62 Temperature Controller Driver 3.26 Setting Example 26  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 63 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the MODE, PARA, >>>, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 64 Temperature Controller Driver 3.27 Setting Example 27  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 65 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the MODE, PARA, >>>, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 66 Temperature Controller Driver 3.28 Setting Example 28  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 67 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the MODE, PARA, >>>, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 68 Temperature Controller Driver 3.29 Setting Example 29  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 69 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 70 Temperature Controller Driver 3.30 Setting Example 30  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 71 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 72 Temperature Controller Driver 3.31 Setting Example 31  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 73 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 74 Temperature Controller Driver 3.32 Setting Example 32  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 75 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 76 Temperature Controller Driver 3.33 Setting Example 33  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 77 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SET, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 78 Temperature Controller Driver 3.34 Setting Example 34  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 79 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 80 Temperature Controller Driver 3.35 Setting Example 35  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 81 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 82 Temperature Controller Driver 3.36 Setting Example 36  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 83 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 84 Temperature Controller Driver 3.37 Setting Example 37  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 85 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the SEL, MODE, UP and Down keys located on the front face of the temperature controller. Please refer to the temperature controller manual for details. ...
Page 86 Temperature Controller Driver 3.38 Setting Example 38  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 87 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the slave address setting switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 88 Temperature Controller Driver 3.39 Setting Example 39  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 89 Temperature Controller Driver  Settings of External Device Communication setting of the external device is set with the slave address setting switch on the front face of the temperature controller and the dip switch in the temperature controller. Please refer to the temperature controller manual for details. ...
Page 90 Temperature Controller Driver 3.40 Setting Example 40  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 91 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 92 Temperature Controller Driver 3.41 Setting Example 41  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 93 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 94 Temperature Controller Driver 3.42 Setting Example 42  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 95 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 96 Temperature Controller Driver 3.43 Setting Example 43  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 97 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 98 Temperature Controller Driver 3.44 Setting Example 44  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 99 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 100 Temperature Controller Driver 3.45 Setting Example 45  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 101 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 102 Temperature Controller Driver 3.46 Setting Example 46  Settings of GP-Pro EX  Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Setting value for Wait To Send differs depending on the External Device. Please refer to the manual of the External Device for more details.
Page 103 Temperature Controller Driver  Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
Page 104: Setup Items
Temperature Controller Driver Setup Items Set communication settings of the Display with GP-Pro EX or in offline mode of the Display. The setting of each parameter must be identical to that of External Device.  "3 Example of Communication Setting" (page 12) Setup Items in GP-Pro EX ...
Page 105 Temperature Controller Driver Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC. Please refer to the manual of the IPC for more detail. •...
Page 106 Temperature Controller Driver Setup Items in Offline Mode • Refer to the Maintenance/Troubleshooting guide for information on how to enter offline mode or about the operation. Maintenance/Troubleshooting Guide "Offline Mode" • The number of the setup items to be displayed for 1 page in the offline mode depends on the Display in use.
Page 107 Temperature Controller Driver Setup Items Setup Description In case of no response from the External Device, use an integer from 0 to 255 to enter how Retry many times the Display retransmits the command. Use an integer from 0 to 255 to enter standby time (ms) for the Display from receiving Wait To Send packets to transmitting next commands.
Page 108 Temperature Controller Driver  Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.
Page 109: Cable Diagram
Temperature Controller Driver Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by RKC INSTRUMENT INC. Please be assured there is no operational problem in applying the cable diagram shown in this manual. •...
Page 110 Temperature Controller Driver Display Cable Notes (Connection Port) GP-4107 (COM1) The cable length GP-4*03T (COM2) User-created cable must be 1200m or GP-4203T (COM1) less. RS-422 terminal block conversion adapter by Pro-face PFXZCBADTM1 GP4000 (COM2) The cable length GP-4201T (COM1) must be 1200m or User-created cable SP5000 (COM1/2) less.
Page 111 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Socket) Termination resistance Signal name Shield External Device 120 (1/2W) Terminal block Termination Signal name resistance Display T/R(B) 120 (1/2W) T/R(A) Shell • 1:n Connection Display D-Sub 9 pin (Socket) Termination Signal name resistance...
Page 112 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Plug) Termination Signal name resistance TERMRX Shield 120Ω (1/2W) External Device Termination Terminal block Display resistance Signal name 120Ω (1/2W) T/R(B) T/R(A) CA4-ADPONL-01 TERMTX Shell User-created cable • 1:n Connection Display D-Sub 9 pin (Plug) Termination...
Page 113 Temperature Controller Driver • 1:1 Connection External Device Display Terminal block D-Sub 9 pin (Socket) Termination Termination resistance Signal name Signal name Shield resistance 120Ω (1/2W) DATA+ T/R(B) 120Ω (1/2W) T/R(A) DATA- Display GND(SG) Shell • 1:n Connection External Device Display External Device Shield...
Page 114 Temperature Controller Driver • 1:1 Connection Display side Terminal block Termination Signal name Shield External Device resistance*1 Terminal block Termination Signal name resistance Display T/R(B) 120Ω (1/2W) T/R(A) • 1:n Connection Display side Terminal block Termination Signal name resistance*1 Shield External Device External Device Shield...
Page 115 Temperature Controller Driver • 1:1 Connection Display side External Device D-Sub 9pin (plug) Terminal block Termination Termination resistance Signal name Signal name Shield resistance 120Ω (1/2W) T/R(B) LINE(+) 120Ω (1/2W) T/R(A) LINE(-) Display GND(SG) RS(RTS) Shell • 1:n Connection Display side External Device External Device Shield...
Page 116 Temperature Controller Driver • 1:1 Connection Termination Display resistance Signal name Shield External Device 120Ω (1/2W) Terminal block Termination Display Signal name resistance 120Ω (1/2W) T/R(B) T/R(A) PFXZCBADTM1 User-created cable • 1:n Connection Display Termination resistance Signal name Shield External Device External Device Shield 120Ω...
Page 117 Temperature Controller Driver Cable Diagram 2 Display Cable Notes (Connection Port) GP3000 (COM1) GP4000 (COM1) SP5000 (COM1/2) The cable length must be ST (COM1) User-created cable 15m or less. LT3000 (COM1) PC/AT The cable length must be GP-4105 (COM1) User-created cable 15m or less.
Page 118 Temperature Controller Driver Display side External Device Terminal block Shield Terminal block Signal name Signal name RD(RXD) SD(TXD) Display ER(DTR) DR(DSR) RS(RTS) CS(CTS) External Device Terminal block Signal name Display Number Name Notes RJ45 RS-232C Cable (5m) by Pro-face PFXZLMCBRJR21 GP-Pro EX Device/PLC Connection Manual...
Page 119 Temperature Controller Driver Cable Diagram 3 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) The cable length must CA3-ADPTRM-01 (COM2) be 1200m or less. LT3000 (COM1) User-created cable User-created cable...
Page 120 Temperature Controller Driver • 1:1 Connection External Device Display Terminal block Shield Termination resistance Signal name Signal name 120Ω (1/2W) Termination T(B) Display resistance CA3-ADPCOM-01 T(A) 120Ω (1/2W) Termination R(B) resistance R(A) CA3-ADPTRM-01 120Ω (1/2W) Termination resistance 120Ω (1/2W) User-created cable •...
Page 121 Temperature Controller Driver • 1:1 Connection External Device Shield Termination Display Terminal block resistance Signal name Signal name 120Ω (1/2W) Termination T(B) Display resistance CA4-ADPONL-01 T(A) 120Ω (1/2W) R(B) Termination resistance R(A) CA3-ADPTRM-01 120Ω (1/2W) Termination resistance 120Ω (1/2W) User-created cable •...
Page 122 Temperature Controller Driver • 1:1 Connection External Device Display side Shield Terminal block Terminal block Termination Signal name Signal name resistance*1 Termination T(B) resistance T(A) 120Ω (1/2W) Display R(B) Termination resistance R(A) Termination 120Ω (1/2W) resistance*1 • 1:n Connection External Device External Device Display side Shield...
Page 123 Temperature Controller Driver • 1:1 Connection External Device Display Terminal block Shield Termination resistance Signal name Signal name 120Ω (1/2W) Termination T(B) Display resistance T(A) 120Ω (1/2W) Termination R(B) resistance R(A) PFXZCBADTM1 120Ω (1/2W) Termination resistance 120Ω (1/2W) User-created cable •...
Page 124 Temperature Controller Driver Cable Diagram 4 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) The cable length must be CA3-ADPTRM-01 (COM2) 1200m or less. LT3000 (COM1) User-created cable User-created cable...
Page 125 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 1 Display Modular 6 pin Shield Signal name Signal name T(B) Display CA3-ADPCOM-01 T(A) R(B) R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection External Device External Device External Device External Device COM.PORT 1 COM.PORT 2 COM.PORT 1...
Page 126 Temperature Controller Driver • 1:1 Connection External Device Display COM.PORT 1 D-Sub 9 pin (Socket) Shield Modular 6 pin Signal name Signal name T(B) T(A) R(B) Display R(A) Shield Shell • 1:n Connection External Device External Device External Device External Device Display COM.PORT 1 COM.PORT 2...
Page 127 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 1 Display Shield Modular 6 pin Signal name Signal name T(B) Display CA4-ADPONL-01 T(A) R(B) R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection External Device External Device External Device External Device COM.PORT 1 COM.PORT 2 COM.PORT 1...
Page 128 Temperature Controller Driver • 1:1 Connection Display External Device D-Sub 9 pin (Plug) COM.PORT 1 Signal name Modular 6 pin Shield Signal name TERMRX CA4-ADPONL-01 T(B) Display T(A) R(B) R(A) Shield TERMTX Shell User-created cable • 1:n Connection Display External Device External Device External Device External Device...
Page 129 Temperature Controller Driver • 1:1 Connection External Device Display side COM.PORT 1 Terminal block Shield Modular 6 pin Signal name Signal name T(B) T(A) R(B) Display R(A) Shield • 1:n Connection External Device External Device External Device External Device Display side COM.PORT 1 COM.PORT 2 COM.PORT 1...
Page 130 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 1 Display Modular 6 pin Shield Signal name Signal name T(B) Display T(A) R(B) R(A) PFXZCBADTM1 Shield User-created cable • 1:n Connection External Device External Device External Device External Device COM.PORT 1 COM.PORT 2 COM.PORT 1 COM.PORT 2...
Page 131 Temperature Controller Driver Cable Diagram 5 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face The cable length must GP-4*01TM (COM1) CA3-ADPTRM-01 be 1200m or less. (COM2) LT3000 (COM1) User-created cable User-created cable...
Page 132 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 1 Modular 6 pin Display CA3-ADPCOM-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection Display External Device External Device External Device External Device Signal name Shield COM.PORT 1 COM.PORT 2...
Page 133 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Socket) External Device Signal name Shield COM.PORT 1 Modular 6 pin Signal name Display T/R(B) T/R(A) Shield Shell • 1:n Connection Display D-Sub 9 pin (Socket) External Device External Device External Device External Device Signal name...
Page 134 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 1 Modular 6 pin Display CA4-ADPONL-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection Display External Device External Device External Device External Device Signal name Shield COM.PORT 1 COM.PORT 2...
Page 135 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Plug) Signal name External Device TERMRX Shield COM.PORT 1 CA4-ADPONL-01 Modular 6 pin Display Signal name T/R(B) T/R(A) Shield TERMTX Shell User-created cable • 1:n Connection Display D-Sub 9 pin (Plug) Signal name External Device External Device...
Page 136 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 1 Display Modular 6 pin Signal name Signal name Shield T/R(B) Display CA3-ADPCOM-01 T/R(A) Shield CA3-ADPTRM-01 User-created cable • 1:n Connection External Device External Device External Device External Device COM.PORT 1 COM.PORT 2 COM.PORT 1 COM.PORT 2...
Page 137 Temperature Controller Driver • 1:1 Connection External Device Display COM.PORT 1 D-Sub 9 pin (Socket) Modular 6 pin Signal name Signal name Shield DATA+ T/R(B) DATA- T/R(A) Display Shield GND(SG) Shell • 1:n Connection External Device External Device External Device External Device Display COM.PORT 1...
Page 138 Temperature Controller Driver • 1:1 Connection Display side Terminal block External Device Signal name Shield COM.PORT 1 Modular 6 pin Signal name Display T/R(B) T/R(A) Shield • 1:n Connection Display side Terminal block External Device External Device External Device External Device Signal name Shield COM.PORT 1...
Page 139 Temperature Controller Driver • 1:1 Connection External Device Display side COM.PORT 1 D-Sub 9pin (plug) Modular 6 pin Signal name Signal name Shield T/R(B) LINE(+) T/R(A) LINE(-) Display Shield GND(SG) RS(RTS) Shell • 1:n Connection External Device External Device External Device External Device Display side COM.PORT 1...
Page 140 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 1 Modular 6 pin Display Signal name T/R(B) T/R(A) PFXZCBADTM1 Shield User-created cable • 1:n Connection Display External Device External Device External Device External Device Signal name Shield COM.PORT 1 COM.PORT 2...
Page 141 Temperature Controller Driver Cable Diagram 6 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) The cable length must CA3-ADPTRM-01 (COM2) be 1200m or less. LT3000 (COM1) User-created cable User-created cable...
Page 142 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 3 Display Shield Modular 6 pin Signal name Signal name T(B) Display CA3-ADPCOM-01 T(A) R(B) R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection External Device External Device COM.PORT 3 COM.PORT 3 Display Shield Modular 6 pin...
Page 143 Temperature Controller Driver • 1:1 Connection External Device Display COM.PORT 3 D-Sub 9 pin (Socket) Modular 6 pin Shield Signal name Signal name T(B) T(A) R(B) Display R(A) Shield Shell • 1:n Connection External Device External Device Display COM.PORT 3 COM.PORT 3 D-Sub 9 pin (Socket) Modular 6 pin...
Page 144 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 3 Display Shield Modular 6 pin Signal name Signal name T(B) Display CA4-ADPONL-01 T(A) R(B) R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection External Device External Device COM.PORT 3 COM.PORT 3 Display Shield Modular 6 pin...
Page 145 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Plug) External Device COM.PORT 3 Signal name Modular 6 pin Shield TERMRX Signal name CA4-ADPONL-01 T(B) Display T(A) R(B) R(A) TERMTX Shield Shell User-created cable • 1:n Connection Display External Device External Device D-Sub 9 pin (Plug) COM.PORT 3...
Page 146 Temperature Controller Driver • 1:1 Connection External Device Display side COM.PORT 3 Modular 6 pin Terminal block Shield Signal name Signal name T(B) T(A) R(B) Display R(A) Shield • 1:n Connection External Device External Device Display side COM.PORT 3 COM.PORT 3 Modular 6 pin Modular 6 pin Terminal block...
Page 147 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 3 Display Shield Modular 6 pin Signal name Signal name T(B) Display T(A) R(B) R(A) PFXZCBADTM1 Shield User-created cable • 1:n Connection External Device External Device COM.PORT 3 COM.PORT 3 Display Shield Modular 6 pin Shield...
Page 148 Temperature Controller Driver Cable Diagram 7 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face The cable length must GP-4*01TM (COM1) CA3-ADPTRM-01 be 1200m or less. (COM2) LT3000 (COM1) User-created cable User-created cable...
Page 149 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 3 Modular 6 pin Display CA3-ADPCOM-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection Display External Device External Device Signal name Shield Shield COM.PORT 3 COM.PORT 3 Modular 6 pin Modular 6 pin...
Page 150 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Socket) External Device Signal name Shield COM.PORT 3 Modular 6 pin Signal name Display T/R(B) T/R(A) Shield Shell • 1:n Connection Display D-Sub 9 pin (Socket) External Device External Device Signal name Shield COM.PORT 3...
Page 151 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 3 Modular 6 pin Display CA4-ADPONL-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 Shield User-created cable • 1:n Connection Display External Device External Device Signal name Shield Shield COM.PORT 3 COM.PORT 3 Modular 6 pin Modular 6 pin...
Page 152 Temperature Controller Driver • 1:1 Connection Display D-Sub 9 pin (Plug) Signal name External Device TERMRX Shield COM.PORT 3 CA4-ADPONL-01 Modular 6 pin Display Signal name T/R(B) T/R(A) Shield TERMTX Shell User-created cable • 1:n Connection Display D-Sub 9 pin (Plug) Signal name External Device External Device...
Page 153 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 3 Display Modular 6 pin Signal name Shield Signal name T/R(B) Display CA3-ADPCOM-01 T/R(A) Shield CA3-ADPTRM-01 User-created cable • 1:n Connection External Device External Device Shield COM.PORT 3 COM.PORT 3 Display Modular 6 pin Modular 6 pin Signal name...
Page 154 Temperature Controller Driver • 1:1 Connection External Device Display COM.PORT 3 D-Sub 9 pin (Socket) Modular 6 pin Signal name Signal name Shield DATA+ T/R(B) DATA- T/R(A) Display Shield GND(SG) Shell • 1:n Connection External Device External Device Display COM.PORT 3 COM.PORT 3 D-Sub 9 pin (Socket) Modular 6 pin...
Page 155 Temperature Controller Driver • 1:1 Connection Display side Terminal block External Device Signal name Shield COM.PORT 3 Modular 6 pin Signal name Display T/R(B) T/R(A) Shield • 1:n Connection Display side Terminal block External Device External Device Signal name Shield COM.PORT 3 COM.PORT 3 Modular 6 pin...
Page 156 Temperature Controller Driver • 1:1 Connection External Device Display side COM.PORT 3 D-Sub 9pin (plug) Modular 6 pin Signal name Signal name Shield LINE(+) T/R(B) T/R(A) LINE(-) Display Shield GND(SG) RS(RTS) Shell • 1:n Connection External Device External Device COM.PORT 3 COM.PORT 3 Display side Modular 6 pin...
Page 157 Temperature Controller Driver • 1:1 Connection Display External Device Signal name Shield COM.PORT 3 Modular 6 pin Display Signal name T/R(B) T/R(A) PFXZCBADTM1 Shield User-created cable • 1:n Connection Display External Device External Device Signal name Shield Shield COM.PORT 3 COM.PORT 3 Modular 6 pin Modular 6 pin...
Page 158 Temperature Controller Driver • 1:1 Connection External Device COM.PORT 3 Modular 6 pin Signal name Display T/R(B) T/R(A) Shield • 1:n Connection External Device External Device COM.PORT 3 COM.PORT 3 Modular 6 pin Modular 6 pin Signal name Signal name Display T/R(B) T/R(B)
Page 159 Temperature Controller Driver Cable Diagram 8 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) The cable length Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) must be 1200m or CA3-ADPTRM-01 (COM2) less. LT3000 (COM1) User-created cable User-created cable...
Page 160 Temperature Controller Driver • 1:1 Connection External Device Modular connector 1 Display Modular 6 pin Shield Termination Signal name Signal name Termination resistance Display CA4-ADPCOM-01 T(B) resistance 120Ω +10% 120Ω +10% or more T(A) or more R(B) Termination CA3-ADPTRM-01 resistance R(A) 120Ω...
Page 161 Temperature Controller Driver • 1:1 Connection External Device Modular connector 1 Display Modular 6 pin Shield Termination Signal name Signal name Termination resistance T(B) resistance 120Ω +10% 120Ω +10% or more T(A) or more Display R(B) Termination CA4-ADPONL-01 resistance R(A) 120Ω...
Page 162 Temperature Controller Driver • 1:1 Connection External Device Display side Modular connector 1 Terminal block Modular 6 pin Shield Termination Termination Signal name Signal name resistance*1 resistance T(B) 120Ω +10% or more T(A) Display R(B) Termination resistance R(A) 120Ω +10% Termination or more resistance*1...
Page 163 Temperature Controller Driver • 1:1 Connection External Device Modular connector 1 Display Modular 6 pin Shield Termination Signal name Signal name Termination resistance Display resistance T(B) 120Ω +10% 120Ω +10% or more T(A) or more R(B) Termination PFXZCBADTM1 resistance R(A) 120Ω...
Page 164 Temperature Controller Driver Cable Diagram 9 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face The cable length must GP-4*01TM (COM1) CA3-ADPTRM-01 be 1200m or less. (COM2) LT3000 (COM1) User-created cable User-created cable...
Page 165 Temperature Controller Driver • 1:1 Connection Display Signal name Shield External Device Terminal block Display CA3-ADPCOM-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection Display Signal name Shield External Device External Device Shield Terminal block Terminal block Display Signal name Signal name CA3-ADPCOM-01...
Page 166 Temperature Controller Driver • 1:1 Connection Display Signal name Shield External Device Terminal block Display CA4-ADPONL-01 Signal name T/R(B) T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection Display Signal name Shield External Device External Device Shield Terminal block Terminal block Display CA4-ADPONL-01 Signal name Signal name...
Page 167 Temperature Controller Driver • 1:1 Connection External Device Display Terminal block Signal name Signal name Shield T/R(B) Display CA3-ADPCOM-01 T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection External Device External Device Shield Display Terminal block Terminal block Signal name Signal name Signal name Shield T/R(B)
Page 168 Temperature Controller Driver • 1:1 Connection External Device Display Terminal block D-Sub 9 pin (Socket) Signal name Signal name Shield T/R(B) DATA+ DATA- T/R(A) Display GND(SG) Shell • 1:n Connection External Device External Device Display Shield Terminal block Terminal block D-Sub 9 pin (Socket) Signal name Signal name...
Page 169 Temperature Controller Driver • 1:1 Connection Display side Terminal block Signal name Shield External Device Terminal block Signal name Display T/R(B) T/R(A) • 1:n Connection Display side Terminal block Signal name Shield External Device External Device Shield Terminal block Terminal block Signal name Signal name Display...
Page 170 Temperature Controller Driver • 1:1 Connection Display side External Device D-Sub 9pin (plug) Terminal block Signal name Signal name Shield T/R(B) LINE(+) T/R(A) LINE(-) Display GND(SG) RS(RTS) Shell • 1:n Connection Display side External Device External Device Shield D-Sub 9pin (plug) Terminal block Terminal block Signal name...
Page 171 Temperature Controller Driver • 1:1 Connection Display Signal name Shield External Device Terminal block Display Signal name T/R(B) T/R(A) PFXZCBADTM1 User-created cable • 1:n Connection Display Signal name Shield External Device External Device Shield Terminal block Terminal block Display Signal name Signal name T/R(B) T/R(B)
Page 172 Temperature Controller Driver Cable Diagram 10 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) The cable length must CA3-ADPTRM-01 (COM2) be 1200m or less. LT3000 (COM1) User-created cable User-created cable...
Page 173 Temperature Controller Driver 10A) • 1:1 Connection External Device Display Shield Terminal block Signal name Signal name T(B) Display CA3-ADPCOM-01 T(A) R(B) R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection External Device External Device Display Shield Shield Terminal block Terminal block Signal name Signal name Signal name...
Page 174 Temperature Controller Driver 10C) • 1:1 Connection External Device Shield Display Terminal block Signal name Signal name T(B) Display CA4-ADPONL-01 T(A) R(B) R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection External Device External Device Display Shield Shield Terminal block Terminal block Signal name Signal name Signal name...
Page 175 Temperature Controller Driver 10E) • 1:1 Connection Display side External Device Terminal block Terminal block Shield Signal name Signal name T(B) T(A) Display R(B) R(A) • 1:n Connection External Device External Device Display side Shield Terminal block Shield Terminal block Terminal block Signal name Signal name...
Page 176 Temperature Controller Driver 10F) • 1:1 Connection External Device Display Shield Terminal block Signal name Signal name T(B) Display T(A) R(B) R(A) PFXZCBADTM1 User-created cable • 1:n Connection External Device External Device Display Shield Shield Terminal block Terminal block Signal name Signal name Signal name T(B)
Page 177 Temperature Controller Driver Cable Diagram 11 Display Cable Notes (Connection Port) GP3000 (COM1) GP4000 (COM1) SP5000 (COM1/2) The cable length must be ST (COM1) User-created cable 15m or less. LT3000 (COM1) PC/AT The cable length must be GP-4105 (COM1) User-created cable 15m or less.
Page 178 Temperature Controller Driver 11C) External Device Modular connector 1 Signal name Display Shield Number Name Notes RJ45 RS-232C Cable (5m) by Pro-face PFXZLMCBRJR21 GP-Pro EX Device/PLC Connection Manual...
Page 179 Temperature Controller Driver Cable Diagram 12 Display Cable Notes (Connection Port) GP3000 (COM1) GP4000 (COM1) SP5000 (COM1/2) The cable length must be ST (COM1) User-created cable 15m or less. LT3000 (COM1) PC/AT The cable length must be GP-4105 (COM1) User-created cable 15m or less.
Page 180 Temperature Controller Driver 12C) External Device COM.PORT 3 Signal name Display Shield Number Name Notes RJ45 RS-232C Cable (5m) by Pro-face PFXZLMCBRJR21 GP-Pro EX Device/PLC Connection Manual...
Page 181 Temperature Controller Driver Cable Diagram 13 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Terminal block conversion adapter by Pro-face GP-4*01TM (COM1) Cable length:1200m or less CA3-ADPTRM-01 (COM2) LT3000 (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01...
Page 182 Temperature Controller Driver 13A) • 1:1 Connection Display side Signal name Shield External Drive side Terminal block Termination Display resistance CA3-ADPCOM-01 Signal name 120 Ω (1/2W) T/R(B) T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection (When connecting with the internal communication line) Display side Signal name Shield...
Page 183 Temperature Controller Driver 13B) • 1:1 Connection Display side D-Sub 9 Pin (socket) Termination resistance Signal name Shield 120 Ω (1/2W) External Device side Terminal block Termination resistance Signal name 120 Ω (1/2W) Display T/R(B) T/R(A) Shell • 1:n Connection (When connecting with the internal communication line) Display side D-Sub 9 Pin (socket) Termination...
Page 184 Temperature Controller Driver 13C) • 1:1 Connection Display side Signal name Shield External Device side Terminal block Termination Display resistance CA4-ADPONL-01 Signal name 120 Ω (1/2W) T/R(B) T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection (When connecting with the internal communication line) Display side Signal name Shield...
Page 185 Temperature Controller Driver 13D) • 1:1 Connection Display side D-Sub 9 Pin (plug) Signal name TERMRX Shield External Device side CA4-ADPONL-01 Terminal block Termination Display resistance Signal name 120 Ω (1/2W) T/R(B) T/R(A) TERMTX Shell User-created cable • 1:n Connection (When connecting with the internal communication line) Display side D-Sub 9 Pin (plug) Signal name...
Page 186 Temperature Controller Driver 13E) • 1:1 Connection Display side Shield External Device side Terminal block Signal name Termination resistance Signal name 120 Ω (1/2W) T/R(B) Display CA3-ADPCOM-01 T/R(A) CA3-ADPTRM-01 User-created cable • 1:n Connection (When connecting with the internal communication line) Display side Shield External Device side...
Page 187 Temperature Controller Driver 13F) • 1:1 Connection Display side External Device side D-Sub 9 Pin (socket) Terminal block Termination Termination Shield resistance resistance Signal name Signal name 120 Ω (1/2W) 120 Ω (1/2W) DATA+ T/R(B) DATA - T/R(A) Display Shell •...
Page 188 Temperature Controller Driver 13G) • 1:1 Connection Display side Terminal block Signal name Termination Shield External Device side resistance*1 Terminal block Termination resistance Signal name 120 Ω (1/2W) Display T/R(B) T/R(A) • 1:n Connection (When connecting with the internal communication line) Display side Terminal block Termination...
Page 189 Temperature Controller Driver 13H) • 1:1 Connection Display side External Device side D-Sub 9pin (plug) Terminal block Termination Termination Shield resistance resistance Signal name Signal name 120 Ω (1/2W) 120 Ω (1/2W) LINE(+) T/R(B) LINE(-) T/R(A) Display GND(SG) RS(RTS) Shell •...
Page 190 Temperature Controller Driver 13I) • 1:1 Connection Display side Signal name Shield External Drive side Terminal block Termination Display resistance Signal name 120 Ω (1/2W) T/R(B) T/R(A) PFXZCBADTM1 User-created cable • 1:n Connection (When connecting with the internal communication line) Display side Signal name Shield...
Page 191 Temperature Controller Driver 13J) • 1:1 Connection External Device side Terminal block Termination resistance Signal name Display 120 Ω (1/2W) T/R(B) T/R(A) • 1:n Connection (When connecting with the internal communication line) External Device side External Device External Device Termination resistance Terminal block 220 Ω...
Page 192 GP3000 (COM1) AGP-3302B (COM2) User-created cable GP-4*01TM (COM1) Cable length: (COM2) 1200m or less Connection cable from RKC INSTRUMENT INC. LT3000 (COM1) W-BF-02 User-created cable Connection cable from RKC INSTRUMENT INC. W-BF-02 Online adapter by Pro-face CA4-ADPONL-01 Terminal block conversion adapter by Pro-face...
Page 193  IPC COM Port (page 9) All GP3000 models except GP-3200 and AGP-3302B To use multiple External Devices, utilize the W-BF-02 connection cable from RKC INSTRUMENT INC. All GP4000 models except GP-4100 series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 14A.
Page 194 Temperature Controller Driver 14B) • 1:1 Connection External Device side Terminal block COM.PORT1 Display side or COM.PORT3 Shield D-Sub 9 Pin (socket) modular connector Termination External resistance Device Signal name Signal name 120 Ω (1/2W) T(B) Termination Connect the terminating resistance T(A) 120 Ω...
Page 195 Temperature Controller Driver 14C) • 1:1 Connection External Device side Terminal block COM.PORT1 Display side or COM.PORT3 Shield Signal name modular connector External Display Device Signal name CA4-ADPONL-01 T(B) Connect the terminating T(A) resistor connector CA3-ADPTRM-01 R(B) W-BW-02 for Z-COM Termination to COM.PORT2 R(A)
Page 196 Temperature Controller Driver 14D) • 1:1 Connection External Device side Terminal block Display side COM.PORT1 D-Sub 9 Pin (plug) or COM.PORT3 Shield modular connector Signal name External Device TERMRX Signal name CA4-ADPONL-01 T(B) Connect the terminating Display T(A) resistor connector W-BW-02 for Z-COM R(B) to COM.PORT2...
Page 197 Temperature Controller Driver 14E) • 1:1 Connection External Device side Terminal block COM.PORT1 Display side or COM.PORT3 Shield Terminal block modular connector External Termination Device Signal name Signal name resistance*1 T(B) Connect the terminating Termination T(A) resistor connector resistance*1 W-BW-02 for Z-COM R(B) Display to COM.PORT2...
Page 198 Temperature Controller Driver 14F) • 1:1 Connection External Device side Terminal block COM.PORT1 Display side or COM.PORT3 Shield modular connector Signal name Display External Device Signal name T(B) Connect the terminating T(A) resistor connector PFXZCBADTM1 W-BW-02 for Z-COM R(B) to COM.PORT2 R(A) or COM.PORT4.
Page 199 GP3000 (COM1) AGP-3302B (COM2) User-created cable Cable length: GP-4*01TM (COM1) 1200m or less (COM2) Connection cable from RKC INSTRUMENT INC. LT3000 (COM1) W-BF-02 User-created cable Connection cable from RKC INSTRUMENT INC. W-BF-02 Online adapter by Pro-face CA4-ADPONL-01 Terminal block conversion adapter by Pro-face...
Page 200 Only the COM port which can communicate by RS-422/485 (2wire) can be used.   IPC COM Port (page 9) To use multiple External Devices, utilize the W-BF-02 connection cable from RKC INSTRUMENT INC. Except GP-4203T All GP4000 models except GP-4100 series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 15A.
Page 201 Temperature Controller Driver 15A) • 1:1 Connection External Device side Display side Terminal block Signal name COM.PORT1 External Shield or COM.PORT3 Device modular connector Display CA3-ADPCOM-01 Connect the terminating Signal name resistor connector T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 CA3-ADPTRM-01 or COM.PORT4.
Page 202 Temperature Controller Driver 15B) • 1:1 Connection External Device side Display side Terminal block D-Sub 9 Pin (socket) Termination COM.PORT1 resistance Signal name External 120 Ω (1/2W) Shield or COM.PORT3 Device modular connector Connect the terminating Signal name resistor connector Display T/R(B) W-BW-01 for Z-COM...
Page 203 Temperature Controller Driver 15C) • 1:1 Connection External Device side Display side Terminal block Signal name COM.PORT1 Shield External or COM.PORT3 Device modular connector Display CA4-ADPONL-01 Connect the terminating Signal name resistor connector T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 CA3-ADPTRM-01 or COM.PORT4.
Page 204 Temperature Controller Driver 15D) • 1:1 Connection Display side External Device side D-Sub 9 Pin (plug) Terminal block Signal name COM.PORT1 External TERMRX Shield or COM.PORT3 CA4-ADPONL-01 Device modular connector Display Connect the terminating Signal name resistor connector T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 or COM.PORT4.
Page 205 Temperature Controller Driver 15E) • 1:1 Connection External Device side Terminal block COM.PORT1 Display side Shield External or COM.PORT3 Device Signal name modular connector Signal name Connect the terminating Display resistor connector T/R(B) CA3-ADPCOM-01 W-BW-01 for Z-COM T/R(A) to COM.PORT2 or COM.PORT4.
Page 206 Temperature Controller Driver 15F) • 1:1 Connection External Device side Terminal block COM.PORT1 External Display side or COM.PORT3 Device D-Sub 9 Pin (socket) Shield modular connector Termination resistance Signal name Connect the terminating 120 Ω (1/2W) Signal name DATA+ resistor connector T/R(B) W-BW-01 for Z-COM DATA -...
Page 207 Temperature Controller Driver 15G) • 1:1 Connection External Device side Display side Terminal block Terminal block COM.PORT1 Termination Signal name External Shield or COM.PORT3 resistance*1 Device modular connector Connect the terminating Signal name resistor connector Display T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 or COM.PORT4.
Page 208 Temperature Controller Driver 15H) • 1:1 Connection External Device side Terminal block COM.PORT1 External Display side or COM.PORT3 Device D-Sub 9pin (plug) modular connector Shield Termination resistance Signal name Connect the terminating 120 Ω (1/2W) Signal name resistor connector LINE(+) T/R(B) W-BW-01 for Z-COM LINE(-)
Page 209 Temperature Controller Driver 15I) • 1:1 Connection External Device side Display side Terminal block Signal name COM.PORT1 External Shield or COM.PORT3 Device modular connector Display Connect the terminating Signal name resistor connector T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 PFXZCBADTM1 or COM.PORT4.
Page 210 Temperature Controller Driver 15J) • 1:1 Connection External Device side Terminal block COM.PORT1 External or COM.PORT3 Device modular connector Connect the terminating Signal name Display resistor connector T/R(B) W-BW-01 for Z-COM T/R(A) to COM.PORT2 or COM.PORT4. • 1:n Connection External Device side External External Terminal block...
Page 211: Supported Device
Temperature Controller Driver Supported Device Range of supported device address is shown in the table below. Please note that the actually supported range of the devices varies depending on the External Device to be used. Please check the actual range in the manual of your connecting equipment.
Page 212 Temperature Controller Driver GP data are as follows depending on the address specifying method. Data of display Data of Specified same as the Specified by adding Specified by adding Specified by adding temperature address 0x1000 to the address 0x2000 to the address 0x3000 to the address controller 1230...
Page 213 Temperature Controller Driver For details of the setting value range or decimal point position of each identifier, please refer to the communication manual of the temperature controller made by RKC INSTRUMENT INC. • The decimal position is saved together with the device string. 0000 Address Decimal position (the setting range is 0 to 3)
Page 214 Temperature Controller Driver CB Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.00-0038.F 0000-0038 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device's manual before use.
Page 215 Temperature Controller Driver Address Identifier Description Control action type selection [SL6] Energized/de-energized alarm selection, special specification selection 1 [SL7] Special specification selection 2 [SL8] Special specification selection 3 [SL9] Option selection [SL10] SV alarm type selection [SL11] Setting limiter (high limit) [SLH] Setting limiter (low limit) [SLL] Setting the position of decimal point [PGdP] Differential gap setting of ON/OFF action [oH]...
Page 216 Temperature Controller Driver FB Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.00-00CF.1F 0000-00CF There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 217 Temperature Controller Driver Address Identifier Description Event 4 set value (EV4) Control loop break alarm (LBA) time LBA deadband Set value (SV) Proportional band [heat-side] Integral time [heat-side] Derivative time [heat-side] Control response parameter Proportional band [cool-side] Integral time [cool-side] Derivative time [cool-side] Overlap/Deadband Manual reset...
Page 218 Temperature Controller Driver Address Identifier Description Remote setting input type Digital input (DI) assignment Output assignment Timer 1 Timer 2 Timer 3 Timer 4 Energized/De-energized Alarm (ALM) lamp lighting condition 1 Alarm (ALM) lamp lighting condition 2 Output status at STOP mode Transmission output type Transmission output scale high Transmission output scale low...
Page 219 Temperature Controller Driver Address Identifier Description Control action Integral/derivative time decimal point position Derivative term operating factor Undershoot suppression factor Derivative gain ON/OFF action differential gap (upper) ON/OFF action differential gap (lower) Action (high) at input error Action (low) at input error Manipulated output value at input error Manipulated output value (MV1) at STOP mode Manipulated output value (MV2) at STOP mode...
Page 220 Temperature Controller Driver Address Identifier Description Startup tuning (ST) ST proportional band adjusting factor ST integral time adjusting factor ST derivative time adjusting factor ST start condition Automatic temperature rise group Automatic temperature rise learning Automatic temperature rise dead time Automatic temperature rise gradient data RUN/STOP group Setting change rate limiter unit time...
Page 221 Temperature Controller Driver HA Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.00-00E8.1F 0000-00E8 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 222 Temperature Controller Driver Address Identifier Description LBA1 deadband Event 4 set value Control loop break alarm 2 (LBA2) time LBA2 deadband Set value (SV1) of input 1 Proportional band of input 1 Integral time of input 1 Derivative time of input 1 Control response parameter of input 1 Set value (SV2) of input 2 Proportional band of input 2...
Page 223 Temperature Controller Driver Address Identifier Description Bar graph display resolution Auto/manual change key operation selection (A/M) Remote/local change key operation selection (R/L) RUN/STOP change key operation selection (R/S) Input type selection of input 1 Display unit selection of input 1 Decimal-point position selection of input 1 Input scale high-limit of input 1 Input scale low-limit of input 1...
Page 224 Temperature Controller Driver Address Identifier Description Event 3 action at input error Event 3 assignment Event 4 type selection Event 4 hold action Event 4 differential gap Event 4 action at input error Event 4 assignment CT1 ratio CT1 assignment CT2 ratio CT2 assignment Hot/Cold start selection...
Page 225 Temperature Controller Driver Address Identifier Description Setting change rate limiter unit time Soak time unit Setting limiter (high) of input 1 Setting limiter (low) of input 1 Setting limiter (high) of input 2 Setting limiter (low) of input 2 ROM version (1-4 character) Integrated operating time Holding peak value ambient temperature Power feed forward input value...
Page 226 Temperature Controller Driver • System area setting that can be used for the temperature controller is reading area size only. Please refer to the GP-Pro EX Reference Manual for system data area. Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)" •...
Page 227 Temperature Controller Driver MA Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-002A.F 0000-002A There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 228 Temperature Controller Driver Address Identifier Description Device address Communication speed Data bit configuration Interval time EEPROM storage mode EEPROM storage status Lock level 1 Lock level 2 • Setting "Use system data area" to GP-Pro EX system area result in improper operation.
Page 229 Temperature Controller Driver SRV Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.0-0085.1F 0000-0085 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 230 Temperature Controller Driver Address Identifier Description D1(ch2) CH2 Derivative time CA(ch1) CH1 Control response designation parameter CA(ch2) CH2 Control response designation parameter V1(ch1) CH1 Overlap/Deadband V1(ch2) CH2 Overlap/Deadband HH(ch1) CH1 Setting change rate limiter HH(ch2) CH2 Setting change rate limiter PB(ch1) CH1 PV bias PB(ch2)
Page 231 Temperature Controller Driver Address Identifier Description HP(ch2) CH2 Control loop break alarm (LBA) usage selection C6(ch1) CH1 Control loop break alarm (LBA) time C6(ch2) CH2 Control loop break alarm (LBA) time V2(ch1) CH1 Control loop break alarm (LBA) deadband V2(ch2) CH2 Control loop break alarm (LBA) deadband DI set DI status...
Page 232 Temperature Controller Driver • System area setting that can be used for the temperature controller is reading area size only. Please refer to the GP-Pro EX Reference Manual for system data area. Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)" •...
Page 233 Temperature Controller Driver SRX Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.00-008C.1F 0000-008C There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 234 Temperature Controller Driver Address Identifier Description A1(ch2) CH2 Event 1 setting value A2(ch1) CH1 Event 2 setting value A2(ch2) CH2 Event 2 setting value EI(ch1) CH1 Operation mode EI(ch2) CH2 Operation mode G1(ch1) CH1 PID/AT transfer G1(ch2) CH2 PID/AT transfer J1(ch1) CH1 Auto/Manual transfer J1(ch2)
Page 235 Temperature Controller Driver Address Identifier Description E5(ch1) CH1 Digital input setting 5 (HOLD) E5(ch2) CH2 Digital input setting 5 (HOLD) E6(ch1) CH1 Digital input setting 6 (STEP) E6(ch2) CH2 Digital input setting 6 (STEP) E7(ch1) CH1 Digital input setting 7 (Program pattern selection) E7(ch2) CH2 Digital input setting 7 (Program pattern selection) E8(ch1)
Page 236 Temperature Controller Driver Address Identifier Description PH(ch2) CH2 Change rate limiter(up) of output PL(ch1) CH1 Change rate limiter(down) of output PL(ch2) CH2 Change rate limiter(down) of output • Setting "Use system data area" to GP-Pro EX system area result in improper operation.
Page 237 Temperature Controller Driver SA Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-001E.F 0000-001E There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 238 Temperature Controller Driver • Setting "Use system data area" to GP-Pro EX system area result in improper operation. Do not set "Use system data area." • System area setting that can be used for the temperature controller is reading area size only. Please refer to the GP-Pro EX Reference Manual for system data area.
Page 239 Temperature Controller Driver SR Mini HG(H-PCP-A/B) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 01/0000.0-01/00BD.F 01/0000-01/00BD 02/0000.0-02/00BD.F 02/0000-02/00BD 03/0000.0-03/00BD.F 03/0000-03/00BD 04/0000.0-04/00BD.F 04/0000-04/00BD 05/0000.0-05/00BD.F 05/0000-05/00BD 06/0000.0-06/00BD.F 06/0000-06/00BD 07/0000.0-07/00BD.F 07/0000-07/00BD 08/0000.0-08/00BD.F 08/0000-08/00BD 09/0000.0-09/00BD.F 09/0000-09/00BD 10/0000.0-10/00BD.F 10/0000-10/00BD...
Page 240 Temperature Controller Driver <Communication identifier list> Address Identifier Description Temperature measured value Alarm 1 status Alarm 2 status Burnout status Heat-side manipulated output value Cool-side manipulated output value Heater break alarm status Current transformer input measured value 1 Current transformer input measured value 2 Set value monitor Temperature rise completion status Error code...
Page 241 Temperature Controller Driver Address Identifier Description AO function selection AO corresponding channel setting AO zooming high limit AO zooming low limit AO zero point correction AO full scale correction DI module input status (DI-A module) CC-Link selecting flag Event DO status (DO-C module) Event DO manual output value (DO-C module) Event DO extension alarm set value Cascade monitor...
Page 242 Temperature Controller Driver Address Identifier Description   Output change rate limiter (down) [ -TIO- , H-CIO-A]   Direct/Reverse action selection [ -TIO- , H-CIO-A]   Hot/Cold start selection [ -TIO- , H-CIO-A]   Start determination point [ -TIO- , H-CIO-A] ...
Page 243 Temperature Controller Driver Address Identifier Description Number of Event DO extension alarm delay times [H-DO-C] Cascade tracking [H-CIO-A] Cascade data selection [H-CIO-A] Cascade DI function selection [H-CIO-A] TI input range number [H-TI-A/B/C] TI digital filter [H-TI-A/B/C] TI alarm 1 differential gap [H-TI-A/B/C] TI alarm 2 differential gap [H-TI-A/B/C] TI alarm 1 type selection [H-TI-A/B/C] TI alarm 2 type selection [H-TI-A/B/C]...
Page 244 Temperature Controller Driver SR Mini HG(H-PCP-J) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 01/0000.0-01/00D4.F 01/0000-01/00D4 02/0000.0-02/00D4.F 02/0000-02/00D4 03/0000.0-03/00D4.F 03/0000-03/00D4 04/0000.0-04/00D4.F 04/0000-04/00D4 05/0000.0-05/00D4.F 05/0000-05/00D4 06/0000.0-06/00D4.F 06/0000-06/00D4 07/0000.0-07/00D4.F 07/0000-07/00D4 08/0000.0-08/00D4.F 08/0000-08/00D4 09/0000.0-09/00D4.F 09/0000-09/00D4 10/0000.0-10/00D4.F 10/0000-10/00D4...
Page 245 Temperature Controller Driver <Communication identifier list> Address Identifier Description  Temperature measured value (PV) [H-TIO- , H-CIO-A] / Motor speed measured value [H-SIO-A]  Alarm 1 status [H-TIO- , H-CIO-A, H-SIO-A]  Alarm 2 status [H-TIO- , H-CIO-A, H-SIO-A]  Burnout status [H-TIO- , H-CIO-A, H-SIO-A] ...
Page 246 Temperature Controller Driver Address Identifier Description AO function selection [H-AO-A/B] AO corresponding channel setting [H-AO-A/B] AO zooming high limit [H-AO-A/B] AO zooming low limit [H-AO-A/B] AO zero point correction [H-AO-A/B] AO full scale correction [H-AO-A/B] H-DI-A module input status [H-DI-A] CC-Link selecting flag Event DO status [H-DO-C] Event DO manual output value [H-DO-C]...
Page 247 Temperature Controller Driver Address Identifier Description  Input error determination point (low) [H-TIO- , H-CIO-A, H-SIO-A]  Action at input error (high) [H-TIO- , H-CIO-A, H-SIO-A]  Action at input error (low) [H-TIO- , H-CIO-A, H-SIO-A]  AT bias [H-TIO- , H-CIO-A, H-SIO-A] ...
Page 248 Temperature Controller Driver Address Identifier Description Display scale low [H-TIO-H/J,H-CIO-A,H-SIO-A] Decimal point position [H-TIO-H/J,H-CIO-A,H-SIO-A] AO display scale high [H-AO-A/B] AO display scale low [H-AO-A/B] AO decimal point position [H-AO-A/B] AO output change rate limiter [H-AO-A/B] Event DO function selection [H-DO-C] Event DO corresponding channel setting [H-DO-C] Event DO mode select setting [H-DO-C] Event DO extension alarm differential gap [H-DO-C]...
Page 249 Temperature Controller Driver Address Identifier Description H-SIO-A auto zero time [H-SIO-A] H-SIO-A alarm hold cancel time [H-SIO-A] H-SIO-A open/closed loop control transfer [H-SIO-A] H-SIO-A correction trigger [H-SIO-A] H-SIO-A correction actual measured value [H-SIO-A] PV bias unit selection [H-TIO-H/J,H-CIO-A,H-SIO-A] H-PCP-J module DO type selection [H-PCP-J] •...
Page 250 Temperature Controller Driver 6.10 REX-F9000 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.00-002F.1F 0000-002F There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 251 Temperature Controller Driver Address Identifier Description Setting limit (Low limit) Proportioning cycle(OUT1) Direct/reverse action selection Power feed forward Alarm 1 type selection First alarm Energized/de-energized selection First alarm Action selection at input abnormality First alarm Hold action selection Alarm 2 type selection Second alarm Energized/de-energized selection Second alarm Action selection at input abnormality Second alarm Hold action selection...
Page 252 Temperature Controller Driver 6.11 REX-F Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-0055.F 0000-0055 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 253 Temperature Controller Driver Address Identifier Description RS digital filter Output limit (High limit) Output limit (Low limit) Cooling output Min. ON time Increase in output change rate limit Decrease in output change rate limit Upper ON/OFF action (A) differential gap Lower ON/OFF action (A) differential gap Manual output at abnormality AT bias...
Page 254 Temperature Controller Driver • Setting "Use system data area" to GP-Pro EX system area result in improper operation. Do not set "Use system data area." • System area setting that can be used for the temperature controller is reading area size only. Please refer to the GP-Pro EX Reference Manual for system data area.
Page 255 Temperature Controller Driver 6.12 REX-D Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-003E.F 0000-003E There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 256 Temperature Controller Driver Address Identifier Description Integral time Derivative time Anti-reset windup(ARW) Cooling-side proportional band Overlap/deadband ON/OFF action differential gap Manual reset Fazzy Proportioning cycle(OUT1) Output limit(High-limit) Output limit(Low-limit) Direct/reverse action selection Proportioning cycle(OUT2) Output limit(high-limit)(OUT2) Analog output specification selection High limit analog output range Low limit analog output range Input type selection...
Page 257 Temperature Controller Driver 6.13 REX-G9 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 *3 Communication identifier 0000.00-005E.1F 0000-005E There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 258 Temperature Controller Driver Address Identifier Description RS digital filter RS Moving average Output limit (High limit) Output limit (Low limit) Increase in output change rate limit Decrease in output change rate limit Upper ON/OFF action (A) differential gap Lower ON/OFF action (A) differential gap Derivative gain Manual output at abnormality AT bias...
Page 259 Temperature Controller Driver Address Identifier Description Second alarm Energized/de-energized selection Second alarm Action selection at input abnormality Second alarm Hold action selection Third alarm Action selection Third alarm Energized/de-energized selection Third alarm Action selection at input abnormality Third alarm Hold action selection Power supply frequency Setting lock No.
Page 260 Temperature Controller Driver 6.14 REX-P300 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 0000.00-001F.1F 0000-001F *1 *2 *3 Communication identifier 002D.00-0078.1F 002D-0078 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 261 Temperature Controller Driver Address Identifier Description FIX set value PV bias PV ratio Level PID setting1 Level PID setting2 Level PID setting3 Digital filter Low level cut-off point First alarm setting Second alarm setting First alarm action selection Second alarm action selection First alarm differential gap Second alarm differential gap First alarm timer...
Page 262 Temperature Controller Driver Address Identifier Description Deadband/Overlap 4 / Control motor neutral zone 4 Fuzzy function 1 Fuzzy function 2 Fuzzy function 3 Fuzzy function 4 Output cycle 1 / Control motor time Output cycle 2 Output limit(High limit) / Integrated output limit Output limit(Low limit) Direct/reverse action selection OUT2 action selection...
Page 263 Temperature Controller Driver 6.15 REX-P250 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-0027.F 0000-0027 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 264 Temperature Controller Driver Address Identifier Description Error code Data all clear Segment remaining time Segment remaining time Segment remaining time • Setting "Use system data area" to GP-Pro EX system area result in improper operation. Do not set "Use system data area." •...
Page 265 Temperature Controller Driver 6.16 REX-AD Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-003B.F 0000-003B There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 266 Temperature Controller Driver Address Identifier Description Third alarm Energized/De-energized Third alarm differential gap Third alarm timer setting selection Fourth alarm action selection Fourth alarm interlock Fourth alarm Energized/De-energized Fourth alarm differential gap Fourth alarm timer setting selection Fifth alarm action selection Fifth alarm interlock Fifth alarm Energized/De-energized Fifth alarm differential gap...
Page 267 Temperature Controller Driver 6.17 REX-PG Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-0021.F 0000-0021 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 268 Temperature Controller Driver • Setting "Use system data area" to GP-Pro EX system area result in improper operation. Do not set "Use system data area." • System area setting that can be used for the temperature controller is reading area size only. Please refer to the GP-Pro EX Reference Manual for system data area.
Page 269 Temperature Controller Driver 6.18 AE500 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-0012.F 0000-0012 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 270 Temperature Controller Driver 6.19 LE100 Series This address can be specified as system data area. Device Bit Address Word Address Notes bits *1 *2 Communication identifier 0000.0-0072.F 0000-0072 There are cases for which writing is not available depending on the device address. Check the identifying attributes of the external device’s manual before use.
Page 271 Temperature Controller Driver Address Identifier Description Set data lock Default setting Error release Decimal point position selection Number of linearizing table setting Linearizing table setting 0 Linearizing table setting 1 Linearizing table setting 2 Linearizing table setting 3 Linearizing table setting 4 Linearizing table setting 5 Linearizing table setting 6 Linearizing table setting 7...
Page 272 Temperature Controller Driver Address Identifier Description Output 6 timer setting Output 7 type selection Output 7 deviation value setting Output 7 interlocking function selection Output 7 a/b contact selection Output 7 differential gap Output 7 timer setting Output 8 type selection Output 8 deviation value setting Output 8 interlocking function selection Output 8 a/b contact selection...
Page 273 Temperature Controller Driver 6.20 SRZ (Z-TIO) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 01/0000.00 01/0000-01/00CF -01/00CF.1F 02/0000.00 02/0000-02/00CF -02/00CF.1F *1 *2 *3*4 Communication identifier 03/0000.00 03/0000-03/00CF -03/00CF.1F 04/0000.00 04/0000-04/00CF -04/00CF.1F There are cases for which writing is not available depending on the device address.
Page 274 Temperature Controller Driver <Communication identifier list> Address Identifier Description Address Identifier Description ROM version Heater break alarm (HBA) set value ROM version Heater break determination point Measured value (PV) Heater melting determination point Comprehensive event state PV bias Operation mode state monitor PV digital filter Error code PV ratio...
Page 275 Temperature Controller Driver Address Identifier Description Address Identifier Description Event 1 differential gap Output limiter (low) [heat-side] Event 1 delay timer Output change rate limiter (up) [cool-side] Force ON of Event 1 action Output change rate limiter (down) [cool-side] Event 2 type Output limiter (high) [cool-side] Event 2 channel setting Output limiter (low) [cool-side]...
Page 276 Temperature Controller Driver Address Identifier Description Address Identifier Description Output distribution master channel mod- Setting limiter (low) ule address Output distribution master channel selec- PV transfer function tion Operation mode assignment 1 (Logic output selection function) Address of interacting modules Logic output 1 to 4 Operation mode assignment 2 (Logic output selection function)
Page 277 Temperature Controller Driver 6.21 SRZ (Z-DIO) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 01/0000.00 01/0000-01/001E -01/001E.1F 02/0000.00 02/0000-02/001E -02/001E.1F 03/0000.00 03/0000-03/001E -03/001E.1F 04/0000.00 04/0000-04/001E -04/001E.1F *1 *2 *3*4 Communication identifier 05/0000.00 05/0000-05/001E -05/001E.1F...
Page 278 Temperature Controller Driver <Communication identifier list> Address Identifier Description Address Identifier Description DO minimum ON/OFF time of ROM version proportioning cycle ROM version DI function assignment Digital input (DI) state 1 Memory area setting signal Digital input (DI) state 2 DO signal assignment module address 1 Digital output (DO) state 1 DO signal assignment module address 2...
Page 279 Temperature Controller Driver 6.22 SRZ (Z-CT) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 01/0000.00 01/0000-01/001D -01/001D.1F 02/0000.00 02/0000-02/001D -02/001D.1F 03/0000.00 03/0000-03/001D -03/001D.1F 04/0000.00 04/0000-04/001D -04/001D.1F 05/0000.00 05/0000-05/001D -05/001D.1F 06/0000.00 06/0000-06/001D -06/001D.1F *1 *2 *3 *4 Communication identifier...
Page 280 Temperature Controller Driver <Communication identifier list> Address Identifier Description Address Identifier Description ROM version Heater overcurrent alarm selection Heater break alarm (HBA) interlock ROM version release Current transformer (CT) input value Heater overcurrent alarm interlock monitor release Load factor conversion CT monitor Set lock Heater break alarm (HBA) state monitor CT type...
Page 281 Temperature Controller Driver 6.23 SRZ (Z-COM) Series This address can be specified as system data area. Device Bit Address Word Address Notes bits 001/0000.00 001/0000-001/0123 -001/0123.1F 002/0000.00 002/0000-002/0123 -002/0123.1F 003/0000.00 003/0000-003/0123 -003/0123.1F *1 *2 *3 *4 Communication identifier 191/0000.00 191/0000-191/0123 -191/0123.1F 192/0000.00 192/0000-192/0123...
Page 282 Temperature Controller Driver <Communication identifier list> Address Identifier Description Address Identifier Description ROM version (Z-COM module) PLC scanning time ROM version (Z-COM module) PLC communication start time Method for setting the number of con- ROM version (Function module) nected modules ROM version (Function module) Slave mapping method Integrated operating time monitor (Z-...
Page 283 Temperature Controller Driver Address Identifier Description Address Identifier Description Event 1 set value (EV1) EDS action wait time (for disturbance 1) Event 2 set value (EV2) EDS action wait time (for disturbance 2) Event 3 set value (EV3) EDS value learning times Event 4 set value (EV4) EDS start signal Control loop break alarm (LBA) time...
Page 284 Temperature Controller Driver Address Identifier Description Address Identifier Description CT ratio Proportional band limiter (low) [heat-side] CT assignment Integral time limiter (high) [heat-side] Heater break alarm (HBA) type Integral time limiter (low) [heat-side] Number of heater break alarm (HBA) Derivative time limiter (high) [heat-side] delay times Hot/Cold start Derivative time limiter (low) [heat-side]...
Page 285 Temperature Controller Driver Address Identifier Description Address Identifier Description Channel selection of interacting modules Z-DIO Interval time Selection switch of interacting modules Current transformer (CT) input value monitor TIO Interval time Load factor conversion CT monitor Digital input (DI) state 1 Heater break alarm (HBA) state monitor Digital input (DI) state 2 Heater overcurrent alarm state monitor...
Page 286: Device Code And Address Code
Temperature Controller Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays. CB Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address FB Series...
Page 287 Temperature Controller Driver SA Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address SR Mini HG(H-PCP-A/B) Series Device Code Device Device Name Channel No. Address Code (HEX) 0080 0180 0280 0380 0480 0580 0680 0780 0880 0980 Communication...
Page 288 Temperature Controller Driver SR Mini HG(H-PCP-J) Series Device Code Device Device Name Channel No. Address Code (HEX) 0080 0180 0280 0380 0480 0580 0680 0780 0880 0980 0A80 Communication 0B80 Word Address identifier 0C80 0D80 0E80 0F80 1080 1180 1280 1380 5E80 5F80...
Page 289 Temperature Controller Driver 7.11 REX-F Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address 7.12 REX-D Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address 7.13 REX-G9 Series Device Code Device Device Name Address Code...
Page 290 Temperature Controller Driver 7.18 AE500 Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address 7.19 LE100 Series Device Code Device Device Name Address Code (HEX) Communication identifier 0080 Word Address 7.20 SRZ (Z-TIO) Series Device Code Device Device Name Channel No.
Page 291 Temperature Controller Driver 7.22 SRZ (Z-CT) Series Device Code Device Device Name Channel No. Address Code (HEX) 0080 0180 0280 0380 0480 0580 Communication identifier Word Address 0680 0780 0880 0980 0A80 0B80 7.23 SRZ (Z-COM) Series Device Code Device Device Name Channel No.
Page 292: Error Messages
Temperature Controller Driver Error Messages Error messages are displayed on the screen of Display as follows: "No. : Device Name: Error Message (Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of External Device where error occurs. Device name is a title of External Device set Device Name with GP-Pro EX.((Initial value [PLC1]) Error Message...

This manual is also suitable for:

Cb500 series Fb900 series Fb400 series Ha900 series Cb400 series Ha901 series ... Show all

RKC INSTRUMENT CB100 Series Connection Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for RKC INSTRUMENT CB100 Series

Summary of Contents for RKC INSTRUMENT CB100 Series

This manual is also suitable for: