Krups EA815 Manual page 28

Automatic rinsing of the circuits when the machine starts.
■ You can choose to program the machine to be rinsed automatically each time it is turned on. To do this, press the
maintenance and settings button
symbol . Press the
rinsing is disabled.
■ You can return to the coffee types menu by pressing the
Warning : after this rinsing process, hot water will be released from the coffee jet. Ensure that the drip tray is in place
even when the machine is not being used. The cycle lasts only a few seconds and stops automatically.
Cleaning program - total duration: approximately 13 minutes
You do not have to run the cleaning program as soon as the appliance requests it, but it must be done reasonably
soon after. If cleaning is postponed, the alert message will remain illuminated until the process is carried out.
■ When the
symbol lights up, you can run the automatic cleaning program by pressing the maintenance and
settings button . The
.
■ the automatic cleaning program is divided into 2 stages: the cleaning cycle itself, followed by the rinse cycle. You
can clean the machine at any time by pressing the maintenance and settings button
button select the cleaning symbol
■ To run this cleaning program, you will need a container which holds at least 0.6 L and which can be placed beneath
the coffee jets and the steam nozzle. The
■ Lift the cup grid (28).
■ Insert the KRUPS cleaning tablet (29).
■ Fill the water container to its maximum level of 1.7 L (2).
■ Empty the coffee grounds collector and the drip tray (23-25).
■ Put a 0.6 L container under the coffee and steam jets (30).
■ Press START
. The
phase has finished, empty the container and the drip dray. The
■ Press START
. The
phase has finished, empty the container and the drip tray. The cycle has finished, the coffee types menu appears.
Note: if you turn off or unplug your machine during cleaning or if there is a power failure, the cleaning program will
start from the beginning of the program once the power is restored to the appliance. It is not possible to postpone
this process. It is obligatory in order to rinse the water circuit. In this case, a new cleaning tablet may be necessary. It
is best to run the full cleaning program in order to avoid any risk of poisoning. The cleaning cycle is irregular: do not
put your hands under the coffee jets while the cycle is running.
Descaling program - duration: approximately 20 minutes
You do not have to run the descaling program as soon as the appliance requests it, but it must be done reasonably
soon after. If descaling is postponed, the alert message will remain illuminated until the process is carried out.
The amount of limescale collected depends on the hardness of your water.
Warning : if your product is fitted with our Claris - Aqua Filter System cartridge, remove the cartridge before descaling.
■ When the
symbol lights up, you can run the automatic descaling program by pressing the maintenance and
settings button (27). If necessary, using the navigation button,
and the function indicator
■ To run the descaling program, you will need a container which holds at least 0.6 L and a sachet of KRUPS descaler.
■ Fill the water tank up to the CALC mark then pour in the contents of one sachet (31).
■ Put a 0.6 L container under the coffee and steam nozzles.
■ Press START
to begin the first phase (approximately 8 min). The
has finished, empty the container and the drip dray. The
using a sponge.
■ Once clean, refill your water tank and replace all parts. The
■ Press START
to begin the second phase (approximately 6 min). The
phase has finished, empty the container and the drip tray. The
■ Press START to begin the final phase (approximately 6 min). The
has finished, empty the container and the drip tray. Descaling is complete.
26
(27). Using the navigation button
button to choose ON which confirms this program. If you press the
symbol is selected. The function indicator
.
symbol flashes.
symbol becomes constant. The first phase (approximately 10 minutes) begins. When this
symbol becomes constant, the final phase (approximately 3 minutes) begins. When this
is located above the maintenance button
, select the automatic rinsing programming
button.
is shown above the maintenance button
symbol flashes. Put the parts back in place.
select the
.
symbol becomes constant. When this phase
and symbols flash. Remove and clean the water tank
symbol disappears.
symbol becomes constant. When this
symbol flashes.
symbol becomes constant. When this phase
, button, automatic
then, using the navigation
symbol. The symbol flashes