Do you have a question about the 57133 and is the answer not in the manual?
Questions and answers
Ellis Abramson
February 24, 2025
Good Morning I have this pump but my tank is only 24" deep and the tube that goes into the tank is too long
1 comments:
Mr. Anderson
February 24, 2025
The Roughneck 120V Heavy-Duty Fuel Transfer Pump includes a suction pipe as part of its packaging contents. To shorten the tube for a 24" deep tank, measure and cut the suction pipe to the appropriate length, ensuring it reaches near the bottom of the tank without restricting flow. Use PTFE tape on the pipe threads for a secure fit during reassembly.
This answer is automatically generated
Robert
July 16, 2025
Do you have a picture of the wiring and switches with the cover off?
Page 1
20V H Heavy y-Duty y Fue el Tra ansfer r Pum Gasoli ne Com mpatible er’s Ma anual WARNING Read caref fully and und derstand all A ASSEMBLY AND OPERA ATION INSTR RUCTIONS b efore operat ing. Failure t to follow the safety rules and other ba asic safety...
Page 2
Thank you very much for choosing a Roughneck™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
Table of Contents Intended Use ............................4 Packaging Contents ..........................4 Technical Specifications ........................4 Electrical Specifications ........................4 Important Safety Information ....................... 5 Specific Operation Warnings ....................... 6 Main Parts of Product ........................... 8 ...
Intended Use The Roughneck 120V Heavy-Duty Fuel Transfer Pump is a positive displacement, rotary vane pump. Depending on installation and viscosity, this pump can deliver up to 20GPM or 76 LPM. The rugged design makes for a long life of dependability.
Important Safety Information ⚠WARNING Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage. The warnings, cautions, and instructions in this manual cannot cover all possible conditions or situations that could occur. Exercise common sense and caution when using this tool. Always be aware of the environment and ensure that the tool is used in a safe and responsible manner.
inattention while operating the tool may result in serious personal injury. Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
Page 7
To prevent serious injury or property damage, read and understand owner’s manual before operating. Know and follow applicable national, state, and local safety codes pertaining to installing and operating electrical equipment for use with flammable liquids. Know and follow all safety precautions when handling petroleum fuels. ...
Main P Parts of P Product Descr ription Qty. Descri iption Qty. Rotor r cover otor Brac cket Bush hing ring sket ring sket al Kit Shift folk Dischar rge hose Junction b box cover Bypass s spring Electric c motor Grounde ed screw Page 8 of 17...
Before Each Use ⚠WARNING To prevent serious injury or property damage, read and understand owner’s manual before operating. Know and follow applicable national, state, and local safety codes pertaining to installing and operating electrical equipment for use with flammable liquids. ...
electrical shock, use extra care when connecting the pump to power. Avoid prolonged skin contact with petroleum fuels. Use protective goggles, gloves and aprons in case of splashing or spills. Change saturated clothing and wash skin promptly with soap and water.
Burn hazard. To reduce the risk of burns, do not touch hot surfaces. Store the product when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. Maintenance Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures.
Problem Possible Cause Corrective Action replace it Air entering the pump or the Check the seals of the connections suction tubing A narrowing in the suction Use tubing suitable for working Tubing under suction pressure Check the voltage at the pump. Low rotation speed Adjust the voltage and/or use cables of greater cross-section...
Parts Lis Descr ription Qty. Descri iption Qty. Rotor r cover otor Brac cket Bush hing ring sket ring sket al Kit Shift folk Dischar rge hose Junction b box cover Bypass s spring Electric c motor Grounde ed screw Page 14 of 1...
Pump chamber Switch bracket Bypass valve Nozzle holder O-ring Auto Nozzle Filter screen Screw 2” Bung adapter Screw Suction tube Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Roughneck product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase.
Page 17
Distributed by orthern Tool & & Equipment t Company, Inc. Burnsvil lle, Minnesot ta 55306 w.northerntoo ol.com Made in Chin Page 17 of 1...
Need help?
Do you have a question about the 57133 and is the answer not in the manual?
Questions and answers
Good Morning I have this pump but my tank is only 24" deep and the tube that goes into the tank is too long
The Roughneck 120V Heavy-Duty Fuel Transfer Pump includes a suction pipe as part of its packaging contents. To shorten the tube for a 24" deep tank, measure and cut the suction pipe to the appropriate length, ensuring it reaches near the bottom of the tank without restricting flow. Use PTFE tape on the pipe threads for a secure fit during reassembly.
This answer is automatically generated
Do you have a picture of the wiring and switches with the cover off?