Download Print this page

Honeywell Minitrend QX Series Installation Instructions

Hide thumbs

Advertisement

Quick Links

QX and SX recorders - Installation Instruction
Processor Board
QX Recorder
This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up
functionality in the recorder. Refer to the User manual for detailed operational requirements.
The QX and SX recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure,
please return the unit to your supplier for repair or upgrade.
Removing the case and opening the back of the recorder should only be performed under the following circumstances:
When an item of hardware requires individual replacement.
When an item of hardware is to be retrospectively fitted.
In all other instances it is recommended that the complete unit be returned to an authorised agent or service centre.
For Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility
WARNING
HAZARDOUS VOLTAGES
Disconnect all power to the recorder before removing the case and attempting any maintenance procedures.
SAFETY TESTS
Upon completion of service procedures detailed in this manual two basic safety tests should be performed in order to
ensure continued safe operation of the instrument.
Earth Resistance; 25 VDC applied between case and protective earth, bonding resistance should be < 0.1 Ohm.
Insulation Resistance; 500Vdc applied between the earth terminal, and the live and neutral terminal shorted together,
insulation resistance to be >2.0 MOhm. (Mega Ohm, NOT milli Ohm)
Failure to comply with these instructions could result in death or serious injury
CAUTION
OBSERVE ANTI-STATIC PRECAUTIONS
Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices.
Full anti-static precautions MUST be observed when in contact with the electronics of your recorder.
SAVE DATA, SETUPS AND LAYOUTS
Removal of PCBs and battery back-up will result in the loss of all non-volatile data.
Ensure all data and set-ups are saved.
Failure to comply with these instructions may result in product damage.
43-TV-33-58 iss.1 GLO June 06 UK
SX Recorder
1

Advertisement

loading

  Summary of Contents for Honeywell Minitrend QX Series

  • Page 1 QX and SX recorders - Installation Instruction Processor Board QX Recorder SX Recorder This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up functionality in the recorder. Refer to the User manual for detailed operational requirements. The QX and SX recorders are designed for ease of assembly with minimal disturbance to the rest of the unit.
  • Page 2: Panel Mounting

    Before attempting to repair or upgrade a recorder, it is advisable to clear a sufficient work space so components such as the front panel can be rested on the work surface without getting scratched or damaged. Panel Mounting Before a new processor board can be fitted the recorder must be removed from the panel. Loosen the mounting clamp screws, slide the clamp towards the rear of the recorder and remove the clamps and the recorder.
  • Page 3: Removing The Processor Board

    Removing the Processor Board To access the processor board the recorder must be placed face down on the bench. Ensure the surface is suitable and that the front of the recorder will not get scratched. Remove the 4 screws (M3x6mm) that secure the processor board to the chassis. The figures below show the position of these screws.
  • Page 4: Inverter Connector

    Once the 4 screws are removed the Processor board can be pulled away from the Mother board. The board can be folded down to rest on the bench with all cables still attached. Fig 3 QX Recorder Fig 4 SX Recorder Inverter Display Touch screen...
  • Page 5 Fitting the new Processor Board Position the new Processor Board as shown in figs 3 or 4 as appropriate. Connect the inverter cable. The connector must be properly orientated before insertion into J13. Failure to do so will bend the pins and may permanently damage the new processor board. Connect the touch screen cable, ensuring there are no twists in the cable.

This manual is also suitable for:

Multitrend sx series