Advertisement

Quick Links

Limited One Year Warranty
T&S warrants to the original purchaser (other
than for purposes of resale) that such product is
free from defects in material and workmanship
for a period of one (1) year from the date of
purchase. During this one-year warranty period,
if the product is found to be defective, T&S shall,
at its options, repair and/or replace it. To obtain
warranty service, products must be returned
to...
T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690
Shipping, freight, insurance, and other
transportation charges of the product to T&S
and the return of repaired or replaced product
to the purchaser are the responsibility of the
purchaser. Repair and/or replacement shall be
made within a reasonable time after receipt by
T&S of the returned product. This warranty does
not cover Items which have received secondary
fi nishing or have been altered or modifi ed after
purchase, or for defects caused by physical
abuse to or misuse of the product, or shipment
of the products.
Any express warranty not provided herein, and
any remedy for Breach of Contract which might
arise, is hereby excluded and disclaimed. Any
implied warranties of merchantability or fi tness
for a particular purpose are limited to one year in
duration. Under no circumstances shall T&S be
liable for loss of use or any special consequential
costs, expenses or damages.
Some states do not allow limitations on how
long and implied warranty lasts or the exclusion
or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may
not apply to you. Specifi c rights under this war-
ranty and other rights vary from state to state.
P/N: 098-015971-45 Rev. 2
Date: 08-26-10
Drawn: TEH
Checked: JRM
10-07-10
Approved: JHB
10-08-10
Installation and
Maintenance
Instructions
B-0108 Series
SPRAY VALVE
#
US Patent
7,150,415
& International Patents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B-0108 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for T&S B-0108 Series

  • Page 1 Items which have received secondary fi nishing or have been altered or modifi ed after purchase, or for defects caused by physical B-0108 Series abuse to or misuse of the product, or shipment of the products. Any express warranty not provided herein, and...
  • Page 2: Exploded View

    Exploded View * Some items are listed for instructional purposes and may not be sold as separate parts.
  • Page 3: Part Number Guide

    Part Number Guide B-0108 Spray Valve Grip, Spray Valve Bugle, Spray Valve Washer Check Valve Spray Face, Spray Valve Body, Spray Valve Liner, Spray Valve Face Seal, Spray Valve Stem Asm, Spray Valve Spring, Compression Plug, Spray Valve Screen, Spray Valve Close Nipple Screws Pivot Pin, Spray Valve...
  • Page 4: General Instructions

    General Instructions Installation: 1. Shut off water supply and drain lines. 2. Remove old spray valve from hose, including handle if applicable. (See images 1 & 2) Note: Make sure that the hose washer is still in place inside the hose barrel before install- ing your new Jet Spray valve.
  • Page 5 General Instructions DC-111 Silicone Grease (1) 1/4” Spanner Bit (1) End Plug Assembly (1) Valve Repair Compression Assembly (1) Spring (1) B-0108 Valve Repair Kit -- 108V-RK 1. Shut off water supply to spray valve. 2. Using the 1/4” spanner bit, unscrew the end plug. Note: Be careful in removing end plug;...
  • Page 6 General Instructions Contractor_______________________________________ SS TRIGGER(1) Architect/Engineer_________________________________ SPRING/TRIGGER CATCH/SCREW SUBASSEMBLY(1) DC-111 SILICONE GREASE(1) LOCTITE 222 TRIGGER SCREW(1) 6-32 X 3/8" PIVOT PIN SCREW(2) ASSEMBLY(1) B-0108 Trigger Repair Kit -- 108T-RK 1. Shut off water supply to spray valve. 2. Using two phillips head screwdrivers, remove the two screws retaining the trigger handle.
  • Page 7 General Instructions Inlet Filter (1) Loctite 222 (1) B-0108 Inlet Screen/Washer Repair Kit -- 108S-RK To replace the inlet screen/washer between the top of the valve body and the 7/8”-20 adapter. 1. Shut off water supply to spray valve. 2. By inserting a 3/8” L-wrench into the 7/8”-20 adapter, unscrew and remove the adapter as well as the screen and washer.
  • Page 8 General Instructions Washer (1) B-0108 Low Flow Spray Face (1) B-0108 Low Flow Spray Face Repair Kit -- 108CSF-RK EPAct 2005 Compliant 0.65 GPM Fan Spray Repair Kit 1. Shut off water supply to spray valve. 2. With hand or pliers, use center ribs to turn the spray face counter-clockwise and re- move spray face and washer.
  • Page 9 General Instructions Washer (1) B-0108 High Flow Washer (1) B-0108 1.48 GPM Spray Face (1) Spray Face (1) HIGH FLOW REGULAR FLOW B-0108 Spray Face Repair Kits 108HSF-RK -- High Flow Spray Face 108SF-RK -- EPAct 2005 Compliant 1.48 GPM Spray Face 1.
  • Page 10 RELATED T&S BRASS PRODUCT LINE B-0107 Pre-Rinse Spray Valve 1.42 GPM - EPAct 2005 Compliant B-0107-C Low Flow Pre-Rinse Spray Valve 0.65 GPM - EPAct 2005 Compliant T&S BRASS AND BRONZE WORKS, INC. A fi rm commitment to application-engineered plumbing products 2 Saddleback Cove, P.O.

Table of Contents