1. Manuals
  2. Brands
  3. netsys Manuals
  4. Network Router
  5. NH-310S
  6. User manual

netsys NH-310S User Manual

Eoc master and slave
Hide thumbs Also See for NH-310S:
Table of Contents

Advertisement

Quick Links

Download this manual
N
H
-
3
1
N
H
-
3
1
E
O
C
M
a
s
t
e
r
E
O
C
M
a
s
t
e
r
U
S
E
R
'
S
M
U
S
E
R
'
S
M
U
S
E
R
'
S
M
0
NH-310M/S EOC Master and Slave USER'S MANUAL Ver.D2
0
M
/
S
0
M
/
S
a
n
d
S
l
a
v
e
a
n
d
S
l
a
v
e
A
N
U
A
L
A
N
U
A
L
A
N
U
A
L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NH-310S and is the answer not in the manual?

Questions and answers

Related Manuals for netsys NH-310S

Summary of Contents for netsys NH-310S

  • Page 1 NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 ’ ’ ’...

  • Page 2: Copyright

    In the interest of improving internal design, operational function, and/or reliability, NETSYS reserves the right to make changes to the products described in this document without notice. NETSYS does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

  • Page 3: Foreword

    Netsys’ NH-310M and NH-310S are the latest technological innovation of HomePNA3.1 Ethernet over coaxial Master and Slave (client) respectively. NH-310M EOC Master is designed to connect with NH-310S MDU Slave for MDU and MTU applications that leverage the two most popular network connections for home use: 10/100Mbps Ethernet connection and coaxial cable connection.

  • Page 4: Safety Warnings

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 Safety Warnings For your safety, be sure to read and follow all warning notices and instructions before using the device. DO NOT open the device or unit. Opening or removing the cover may expose you to dangerous high voltage points or other risks.

  • Page 5: Table Of Contents

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 TABLE OF CONTENTS COPYRIGHT ................................1 FOREWORD ................................2 SAFETY WARNINGS..............................3 CHAPTER 1. UNPACKING INFORMATION......................6 Check List..................................... 6 CHAPTER 2. HARDWARE DESCRIPTION......................7 2.1 Front Panel ....................................... 8 2.2 Pront Indicators....................................9 2.3 Rear Panel .......................................11 CHAPTER 3.
  • Page 6 NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 CHAPTER 4. CONFIGURE NH-310M/S VIA ENGINEERING TOOL..............17 4.1 Configure NH-310M/S via Engineering Tool ..........................17 APPENDIX A: CABLE REQUIREMENTS....................... 24 APPENDIX B: PRODUCT SPECIFICATION ......................26 APPENDIX C: TROUBLESHOOTING ........................29 APPENDIX D: COMPLIANCE AND SAFETY INFORMATION ................

  • Page 7: Chapter 1. Unpacking Information

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 Chapter 1. Unpacking Information 1.1 Check List Thank you for choosing Netsys NH-310M/S. Before installing the EOC product, please verify the contents inside the package. Package Contents: NH-310M or NH-310S Device 4 x rubber feet...

  • Page 8: Chapter 2. Hardware Description

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 Chapter 2. Hardware Description This chapter describes the important parts of the device. It features the front indicators and rear connectors. NH-310M Outward NH-310S Outward...

  • Page 9: Front Panel

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 2.1 Front Panel The front panel provides a simple interface monitoring of the Master/Slave. (Figure 2.1). Figure 2.1 NH-310M and NH-310S Front Panel...

  • Page 10: Pront Indicators

    NH-310M/S EOC Master and Slave USER’S MANUAL Ver.D2 2.2 Pront Indicators The NH-310M has Four LED indicators. The following Table shows the description. (Table 2-1) LEDs Color Status Descriptions The HCNA is receiving the power and also functioning properly Power Green The HCNA is not ready or has malfunctioned The LAN port is connected to Ethernet devices...
  • Page 11 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 The NH-310S has LED indicators. The following Table shows the description. (Table 2-2) LEDs Color Status Descriptions The HCNA is receiving the power and also functioning properly Power Green The HCNA is not ready or has malfunctioned...

  • Page 12: Rear Panel

    2.3 Rear Panel The rear panel provides the physical connectors connected to the power adapter and any other network device. (Figure 2.2) Figure 2.2 Rear panel of the NH-310M and NH-310S And the table shows the description. (Table 2-3) Connectors...

  • Page 13: Chapter 3. Installation

    • Place the device away from direct sunlight, heat sources, or areas with a high amount of electromagnetic interference. • If you trying to setup basic connection between NH-310M and NH-310S, you need to add at least -10dB attenuator (5MHz-850MHz).

  • Page 14: General Rules

    Slave device. Please choose according to different environments to different specifications of the Diplexer (5MHz-45MHz, 47MHz-1GHz) or Multi-Splitter (5MHz-1Ghz). Attenuator Establish the basic link for NH-310M and NH-310S, please add a attenuator (at least -10 dB 5M-850MHz). Attenuator Diplexer...

  • Page 15: Hcna Connections

    -145dBm/Hz noise floor. But make sure that the connector is inserted properly and lock. Ethernet cable used must conform to FCC standard to ensure data integrity and it should not exceed 100meters (328feet). The NH-310M EOC (Ethernet over coaxial) MDU Master can support up to 60(maximum) NH-310S Slave (Clients). Notes: 1.
  • Page 16 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Figure 3.1 NH-310M/S connection diagram...
  • Page 17 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Figure 3.2 NH-310M/S connection diagram-2...

  • Page 18: Chapter 4. Configure Nh-310M/S Via Engineering Tool

    NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Chapter 4. Configure NH-310M/S via Engineering Tool Configure NH-310M/S via Engineering Tool Engineering tool is used for testing signal performance and integrity. As well as update firmware and show device information. To use engineering tool, make sure to connect the master and slave as shown in figure 4 at page 13.
  • Page 19 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Figure 4.1-2 Command Prompt diagram Netinf It is the command for network information such as SNR, rate, Rx power and etc.
  • Page 20 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Address It is the command for showing MAC address information of its device. Devinf It is the command for device information such as number of endpoints, MAC address, H/W version and etc.
  • Page 21 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Getstations It is the command for all the MAC address of the connected endpoints.
  • Page 22 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Netper It is the command for networks packet error rate (PER). Noisetest It is the command for testing noise based on frequency and time.
  • Page 23 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2...
  • Page 24 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2...

  • Page 25: Appendix A: Cable Requirements

    NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Appendix A: Cable Requirements A CAT 3, 4 or 5 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet device to the device. A 10Base-T cable often consists of four pairs of wires, two of which are used for transmission. The connector at the end of the10Base-T cable is referred to as an RJ-45 connector and it consists of eight pins.
  • Page 26 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Figure A-2 Pin Assignments and Wiring for an RJ-45 Straight-Through Cable Figure A-3 Pin Assignments and Wiring for an RJ-45 Crossover Cable...

  • Page 27: Appendix B: Product Specification

    NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Appendix B: Product Specification Key Features & Benefits Compliant with HomePNA3.1/ HomePNA3.0 over Coaxial cable(HCNA) specifications (ITU-T G.9954) Compliant with IEEE802.3 10Base-T and IEEE802.3u 100Base-Tx standards Compliant with IEEE802.3x Flow Control standard Provide 2 x 10/100M auto-negotiation RJ-45 Ethernet ports with auto-MDI/MDIX Provides 2 x F-type female coax connectors for HCNA(12M-44MHz) and TV(47M-1GHz) Support transmission speed up to 256Mbps over coaxial cable and link establish under -145dBm/Hz Noise Floor...
  • Page 28 1 x Power LED 1 x HCNA Link/Activity LED NH-310M LED Indicators: 2 x Ethernet Link/Activity LED 1 x Power LED 1 x HCNA Link/Activity LED NH-310S LED Indicators: 2 x Ethernet Link/Activity LED Up to 256Mbps Max Bandwidth: -145dBm/Hz Max Noise Floor:...
  • Page 29 NH-310M: 130mm x 94.5mm x 27mm (5.12” x 3.72“ x 1.06“) (L x W x H) Dimension: NH-310S: 130mm x 94.5mm x 27mm (5.12” x 3.72“ x 1.06“) (L x W x H) Operating: 0ºC ~ 50ºC (32ºF ~ 122ºF) Temperature: Storage: -20ºC ~ 70ºC (-4ºF ~ 158ºF)

  • Page 30: Appendix C: Troubleshooting

    The link is failed between NH-310M and NH-310S. The functionality of NH-310S is abnormal. Cause: The output level of voltage is too high for short connection. It must use the attenuator to be connected with MDU Master NH-310M and Slave NH-310S to Solution: attenuate the transmission power level to -10dBm(5MHz-850MHz) at least.
  • Page 31 HCNA port of Slave via splitter then the connection’s ok. The TV port of Master connect to HCNA port of Slave is not correct, It why can link establish the reason using a short cable, causing HPNA signal of NH-310S too strong and pass to HPNA port of Answer:...
  • Page 32 4. HPNA3.1 must use 75 ohm coaxial cable. If use 50 ohm impendence, the performance will be less than half. 8. Question: How much node(Mac Address) can be connected to behind of the NH-310S. Answer: Each of the NH-310S can only be connected to 16 nodes (Mac Address).
  • Page 33 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 System Diagnostics Power and Cooling If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section. However, if the unit power is off after running for a while, check for loose power connections, power losses or surges at the power outlet.
  • Page 34 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Physical Configuration If problems occur after altering the network configuration, restore the original connections, and try to track the problem down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation do not exceed recommendations.

  • Page 35: Appendix D: Compliance And Safety Information

    NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Appendix D: Compliance and Safety Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 subpart B of FCC class A rules.
  • Page 36 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 functioning of your equipment. If they do, you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
  • Page 37 NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 FCC Warning This equipment has been tested to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 38: Chinese Sj/T 11364-2014

    NV-310M/S EOC Master and Slave USER’S MANUAL Ver. D2 Chinese SJ/T 11364-2014 有 毒 有 害 物 质 或 元 素 部件名称 铅(Pb) 汞(Hg) 镉(Cd) 六价铬[Cr(VI)] 多溴联苯(PBB) 多溴二苯醚(PBDE) 结构壳体 ○ ○ ○ ○ ○ ○ 电路组 ○ ○ ○ ○ ○...

This manual is also suitable for:

Nh-310m

Table of Contents