1. Manuals
  2. Brands
  3. Chargery Manuals
  4. Battery Charger
  5. C4012B
  6. Instruction manual

Chargery C4012B Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C4012B
for up to 12S LiPo & LiFe & LiTo
3mV voltage accuracy
1500W charge power at AC
500W charge power at DC
1.2A balance current
2.8" TFT LCD display
T
hanks for your purchasing the 1500W CHARGER for your e-Vehicle or RC model.
R
ead the ENTIRE instruction manual to become familiar with the features/functions of the device
before operating.
F
eel free to send an email to
jasonwang3a@163.com
or call at 86 755 2643 6165 should you have
any questions and suggestions.
Jason Wang

Advertisement

Table of Contents
loading

Related Manuals for Chargery C4012B

Summary of Contents for Chargery C4012B

  • Page 1 C4012B for up to 12S LiPo & LiFe & LiTo 3mV voltage accuracy 1500W charge power at AC 500W charge power at DC 1.2A balance current 2.8” TFT LCD display hanks for your purchasing the 1500W CHARGER for your e-Vehicle or RC model.

  • Page 2: Safety Notes

    Copyright@Chargery Power Co., Ltd. All rights reserved. Without prior written consent by Shenzhen Chargery Power Co., Ltd, any units or individual extract and copy parts or entire contents of this manual, and transmission in any form is illegal and strictly prohibited.

  • Page 3: Special Features

    C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Special Features Unique charge architecture realized better transient response to any changes of voltage on input and output. The charger use advanced ADC measurement technology, high accuracy, high voltage and high current detection circuit. The maximum voltage measurements tolerance is within 5mV at up to 12S LiPo battery.

  • Page 4: Mechanical Characteristics

    Connect to power supply or battery, DC voltage range is 10V to 28V, absolutely 30V maximal AC Input Connect to AC source 90-265V 50/60Hz USB port Connect to PC update the firmware by Chargery UpdateTool. Output port Connect to battery. Connect to temperature sensor monitor battery temperature, the sensor must be pasted Temperature tightly battery during charge or discharge.

  • Page 5: Program Setting

    C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Program Setting On Battery Type interface, Press Knob button for 3 seconds enter into CHARGER SETTING interface. Rotate Knob button select the item, press Knob shortly make the value flash, and rotate change the value. Press knob button shortly confirm the change.
  • Page 6 Dual Input Synchronous Balancer/Charger/Discharger Operating guideline Connect the charger to power supply or battery pack with 10-28V, the unit will start and display Chargery logo, model, version and series number, 2 seconds later, main interface is displayed. as following picture.
  • Page 7 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Press Knob shortly on any function, the function parameters setup interface will be displayed, Press Knob choose item and rotate Knob modify. For all lithium battery, there are Charge, Balance Charge, Discharge, Storage, Cycle and Balance functions. Take as LiPo Charge as sample. The details are as below pictures.
  • Page 8 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Ignore means the charged capacity cannot be as control condition. Auto means the charger will identify cell count automatically Charge and discharge terminal voltage is most important, if cannot confirm battery chemistry, please read battery datasheet, and then setup the voltage per cell according to battery datasheet.
  • Page 9 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger For NiMh/NiCd battery, there are Charge, Discharge and Cycle functions. As below pictures. The Details of parameters set up for NiMH/NiCd battery is in the following table. Parameters Min. Default Max. Step unit Charge...
  • Page 10 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger For Pb acid battery (VRLA)battery, there are Charge, Discharge and Cycle functions. As below pictures. The details of parameters set up for Pb acid battery (VRLA) is in the following table. Parameters Min. Default Max.
  • Page 11 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger As power supply When connect the charger to AC source, on Battery type interface, choose power supply setup output voltage and maximal output current, the charger will work as a programmed power supply; you can set up the output voltage and maximal output current, and then press for 3 seconds power on the charger.
  • Page 12 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Tips In main interface, press for 3 seconds, the charger will enter into function interface directly, press for 3 seconds will operate last program directly. During charge in CC phase, the charge current can be set up to new value and need not stop charging.

  • Page 13: Firmware Upgrades Via Usb Port

    Dual Input Synchronous Balancer/Charger/Discharger Firmware Upgrades via USB Port Go to http://www.chargery.com/uploadFiles/ChargeryupdateTool.zip to download the ChargeryupdateTool.zip, the zip file include Chargery USB driver, and Chargery Update Tool, extract to any disk on the PC. install driver, program X:\ChargeryupdateTool\ChargeryUSBdriver.exe (where X is the drive letter designator for your CD-ROM drive.)

  • Page 14: Typical Connection

    C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Typical Connection The charger have two balance port for 2S-6S and 7-12S separately, each balance port can connect to 2S-6S battery, if you have one battery pack under 6S such as 2S, 3S, 4S, 5S, you can connect the battery to balance port by adapter board, if you have two battery but total cell count is under 6S such as 3S+3S, 2S+2S, The connection is as below, two 3S packs will be charged as one 6S pack.
  • Page 15 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger If you have two battery and total cell count is over 6S such as 5S+5S, 4S+4S, 6S+6S, 5S+3S, 3S+6S, and so on The connection is as below, two 5S packs will be charged as one 10S pack. For 6S+6S, if battery connector is XH type, you can connect the battery to balance port directly and need not adapter wire and adapter board.
  • Page 16 C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Accessory AC Input wire, 1500mm DC Input wire, 600mm Adapter wire: connect adapter board to Adapter board:CCB-7KT for 6S battery balance port on C4012B Temperature sensor USB data line www.chargery.com page 16 total 18...

  • Page 17: Related Parts

    C4012B V1.24 Dual Input Synchronous Balancer/Charger/Discharger Related parts The following device is related with 500W CHARGER MODEL DESCRIPTION COMMENTS 5006B 1-6S Li-Ion/LiPo/LiFe battery, 1.3A balance current 5008B 1-8S Li-Ion/LiPo/LiFe battery, 1.3A balance current 50010B 1-10S Li-Ion/LiPo/LiFe battery, 1.3A balance current...

  • Page 18: Version History

    Fix a bug on balance charge mode Warranty and Service Chargery Power Co., Ltd. as manufacture of 1500W/500W CHARGER to be free of defects in material and workmanship. This warranty is effective for 12 months from date of purchase. If within the warranty period the customer is not satisfied with the products performance resulting from a manufacturing defect, the accessory will be replaced or repaired.

Table of Contents