Roger Technology AG CTRL Instruction And Warnings For The Installer
  1. Manuals
  2. Brands
  3. Roger Technology Manuals
  4. Controller
  5. AG CTRL
  6. Instruction and warnings for the installer

Roger Technology AG CTRL Instruction And Warnings For The Installer

Hide thumbs Also See for AG CTRL:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction and Warnings for the Installer
IT -
Istruzioni ed avvertenze per l'installatore
EN -
DE -
FR -
ES -
Instrucciones y advertencias para el instalador
PT -
Instruções e advertências para o instalador
IS88 Rev.05 31/01/2017
AG CTRL
serie AGILIK 4 e 6
Istruzioni originali
- pag. 13
- pag. 39
- pág. 117
- pág. 143
- S. 65
- p. 91

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AG CTRL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Roger Technology AG CTRL

Summary of Contents for Roger Technology AG CTRL

  • Page 1: Sblocco Meccanico

    IS88 Rev.05 31/01/2017 AG CTRL serie AGILIK 4 e 6 Istruzioni originali IT - Istruzioni ed avvertenze per l’installatore - pag. 13 EN - - pag. 39 DE - - S. 65 FR - - p. 91 ES - Instrucciones y advertencias para el instalador - pág.

  • Page 2: Table Of Contents

    Indice dei parametri Index des paramètres Avvertenze generali Consignes générales de sécurité Allumage ou mise en service Accensione o messa in servizio Apprendimento della corsa 10 Menu paramètres 10 Menù parametri 11 Commandes et accessoires 11 Comandi e accessori 13 Segnalazione degli ingressi di sicurezza e (modalités TEST) dei comandi (modalità...
  • Page 3 Warning area and prevent collisions in all circumstances. AG/CTRL barrier. AG/CTRL ) or later. installing G90/F4ES or T90/F4S...
  • Page 4 AG/004 - AG/006 AG/004/115V - AG/006/115V 230 Vac ± 10% 50Hz 115Vac ± 10% 60Hz 270 W 36 Vac 220 W LIGHT 12 W 24 Vdc 10 W 12 Vdc 3 W 24 Vdc 10 W 24 Vdc -20°C +55°C IP4X Figure 1 TRANSFORMER...
  • Page 5 Lcable = 1÷20 m R85/60 Lcable 1÷20 m N.B. N.B. BATTERY (+) BATTERY (-)
  • Page 6 Previous parameter DOWN PROG TEST TEST + and - + or - Parameter display mode...
  • Page 7 POWER C485 STOP/RELEASE TEST mode OR). display. Release device open. N.B. Standby mode Press UP + or - POWER...
  • Page 8 and 6 m. or injury. TEST Vedi capitoli 13 e 14 “Segnalazioni”. TEST Sì CHIUSA TEST SBLOCCARE BLOCCARE PROG AP P- PH A5 PH A5 AU to x4 s 2x360° 2x360° OPENING APERTURA Sì AU to OPEN APERTA CHIUSURA CHIUSA mode.
  • Page 9 PARAM. PAGE Enable electric lock...
  • Page 10 PARAM. PAGE HW version FW version...

  • Page 11: Parameters Menu

    Parameters menu illuminates C485 standard Parameter 4.5 m. to 6 m. parameter...
  • Page 12 Open-stop-close-stop-open-stop-close... noeuvre noeuvre Open-close-open-close. Open-close-stop-open. to terminal SC 01= barrier decelerates near stop ...
  • Page 13 ity).
  • Page 14 noeuvre. cleared. noeuvre. cleared. (FT) 01= rapid braking/smaller stopping distance 4 m).
  • Page 15 OPENING. set: ignored.
  • Page 16 is not visible. rameter a reopening manoeuvre unless parameter is set. Parameters are not visible. is not visible. immediately. FT (NC) and PED...
  • Page 17 x4 s N.B. Serial number FW version N.B.
  • Page 18 N.B. N.B. = 123 days + and - = ). = ). + and - = ).

  • Page 19: Commands And Accessories

    Commands and Accessories N.C. (Normally Closed). 11(SC). 11(SC) a barrier open indicator lamp cannot be connected. or later). 19 20...
  • Page 20 19 20 is enabled. 21(ST) or set parameter 24(FT) – opening manoeuvre. – – FT is obstructed. 24(FT) - parameters WARNING! Use G90/F4ES or T90/F4S FT may be used to receive a closing 26(ANT) N.B. 29(PED) 30(PP) Close command input (NO). Open command input (NO).
  • Page 21 ENC1 encoder cable. ENC2 encoder cable. barrier in- RECEIVER CARD – PR1 – PR2 AG/BAT/KIT BATTERY controller unit accepts no commands. is restored. Parameter order.
  • Page 22 AG/CTRL immediately. AP open command (terminal block). FT (NC) and PED Tempo di chiusura automa ca Automa c closing...
  • Page 23 DISPLAY rier). troller. Release device open. tact is connected correctly. not connected used or to disable. or incorrectly connected. FT not connected or in- correctly connected. ures 3-4). correctly connected. may be incorrectly connected. used.
  • Page 24 ALARM SIGNAL Overcurrent detected in inverter. TEST mand requests in succession. in alarm state. parameter or close. message is displayed: disappears Release device open. Encoder 1 not connected. problem persists. Encoder 2 not connected. problem persists.
  • Page 25 ALARM SIGNAL Press TEST (EnE5) Press TEST or close. gered. minutes. (btLO) barrier. Controller unit models not compat- ible. troller units. problems. not complete correctly. voltage. rameter desired manoeuvre. cor- cor- type. stops. Radio signals are impeded by metal Barrier open indicator lamp N.B.
  • Page 26 TEST TEST PER USCIRE 1 click DALLA MODALITA’ x5 s AG/CTRL controller. Parameter E.g. . = 1 s / . motors overcurrent. + / -...

  • Page 27: Maintenance

    parameters correctly. Maintenance Disposal...
  • Page 28 AG/CTRL – 2006/42/EC; – 2011/65/EC EN 61000-6-3; EN 61000-6-2. | 14.

Table of Contents