IFM Electronic TAD 91 Series Operating Instructions Manual
IFM Electronic TAD 91 Series Operating Instructions Manual

IFM Electronic TAD 91 Series Operating Instructions Manual

Temperature transmitter

Advertisement

Quick Links

Operating instructions
Temperature transmitter
UK
TADx81
TADx91

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TAD 91 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for IFM Electronic TAD 91 Series

  • Page 1 Operating instructions Temperature transmitter TADx81 TADx91...
  • Page 2: Table Of Contents

    Contents 1 Preliminary note ���������������������������������������������������������������������������������������������������3 1�1 Symbols used ������������������������������������������������������������������������������������������������3 2 Safety instructions �����������������������������������������������������������������������������������������������3 3 Getting started �����������������������������������������������������������������������������������������������������4 4 Functions and features ����������������������������������������������������������������������������������������4 5 Function ���������������������������������������������������������������������������������������������������������������5 5�1 Analogue function ������������������������������������������������������������������������������������������5 5�2 Diagnostic function ����������������������������������������������������������������������������������������6 5�2�1 Drift monitoring ������������������������������������������������������������������������������������7 5�2�2 Sensor backup (redundancy switching) ������������������������������������������������8 5�2�3 Diagnostic cases ����������������������������������������������������������������������������������8 5�2�4 Diagnostic function in 2-wire operation �������������������������������������������������8 5�2�5 Diagnostic function in 3-wire operation �������������������������������������������������9...
  • Page 3: Preliminary Note

    1 Preliminary note Technical data, approvals, accessories and further information at www�ifm�com� 1.1 Symbols used ► Instructions > Reaction, result […] Designation of keys, buttons or indications → Cross-reference Important note Non-compliance may result in malfunction or interference� Information Supplementary note� 2 Safety instructions •...
  • Page 4: Getting Started

    3 Getting started Detailed description under → 8 Parameter setting� 1� Connect unit to PC to set the parameters via the IO-Link interface� 2� Set the standard unit of measurement� - [Uni]: °C or °F 3� Set analogue signal (→ 5.1)� - [OU2]: I = 4���20 mA or I neg = 20���4 mA - [ASP] and [AEP]: scaling of the measuring range�...
  • Page 5: Function

    5 Function • The unit features an IO-Link interface� • The unit is designed for two or three-wire operation� Depending on the operat- ing mode the following output signals are provided: Operating Output signals mode 2 wires OUT: analogue signal for temperature measurement / analogue signal for diagnostics 3 wires OUT1: switching signal for diagnostics / IO-Link...
  • Page 6: 5�2 Diagnostic Function

    temperature value continues to increase or decrease, case of diagnostic 5 occurs (→ 5.2.3)� I [mA] FOU = On 21.5 20.5 FOU = OFF T [°C] Figure 1: Output characteristics analogue output with factory setting Setting [OU2] = I Setting [OU2] = Ineg MAW = initial value of the measuring range, MEW = final value of the measuring range, ASP = analogue start point, AEP = analogue end point 5.2 Diagnostic function...
  • Page 7: 5�2�1 Drift Monitoring

    5.2.1 Drift monitoring For drift monitoring the unit compares the temperature deviation of sensor element 1 (NTC) and sensor element 2 (Pt 1000) from the mean value� The permissible temperature deviation is defined by the parameters drW = warning threshold and drA = alarm threshold�...
  • Page 8: 5�2�2 Sensor Backup (Redundancy Switching)

    5.2.2 Sensor backup (redundancy switching) If one of the two sensor elements fails (= diagnostic case 4 → 5.2.3), it is possible to continue to measure the temperature with the other sensor element that is still operational (sensor backup → 10 Fault correction; Fnr 21)� However, drift monitor- ing is not possible any more�...
  • Page 9: 5�2�5 Diagnostic Function In 3-Wire Operation

    Diagnostic messages Diagnostic cases [drEd] Warning Alarm Failure (→ 5.2.3) = ON ● 7���9 ● ● = ONdr 3���9 ● ● ● = OFF 1���9 Table 1: Setting of diagnostic cases to be signalled (2-wire operation) - Setting [drEd] = ON provides maximum availability since the transmission of the meas- ured temperature value is only interrupted for the diagnostic message in diagnostic cases of category "failure"�...
  • Page 10: 5�3 Io-Link

    Since all diagnostic cases can be signalled via the switching output in 3-wire operation, the analogue output only leaves its measured tempera- ture value in diagnostic case of category "failure"� This ensures maximum use of the analogue output� The parameter [dOU1] is used to define how the diagnostic output reacts to diag- nostic messages: Diagnostic message Normal...
  • Page 11: Installation

    6 Installation ► Before installing and removing the unit make sure that no pressure is applied to the system and there is no medium in the pipe� ► Note dangers related to extreme machine / medium temperatures� Information about the available adapters at www�ifm�com� ►...
  • Page 12: 6�3 Use In Hygienic Areas

    6.3 Use in hygienic areas to 3-A The following applies to units with 3-A certification: ► Only use adapters with A-3 certification for the process connection� ► Do not install the unit at the lowest point of the pipe or tank (→ position 5) in order that the medium can run off the area of the measuring element�...
  • Page 13: Electrical Connection

    7 Electrical connection The unit must be connected by a qualified electrician� The national and international regulations for the installation of electrical equipment must be adhered to� Voltage supply to EN 50178, SELV, PELV / "supply class 2" to cULus� ►...
  • Page 14: Parameter Setting

    8 Parameter setting Using an IO-Link capable parameter setting tool, the following options are available: - Reading current process values� - Reading, changing and saving current parameter settings and transmitting them to other units of the same type� - Read saved diagnostic information (→ 10)� ►...
  • Page 15: Operation

    Drift failure threshold: [drF] = drA + 3 K; if this value of the temperature deviation is exceeded, a diagnostic message of the category "failure" is provided� • drF cannot be set but results from the setting of drA� • Setting drA = OFF automatically results in: drF = 8 K Delay of the drift detection�...
  • Page 16: Fault Correction

    10 Fault correction In case of faults or anomalies: ► Connect unit with a PC� ► Read [Fnr]� Fnr Type of fault Corrective measures No fault, no anomaly occurred� Internal malfunction in the sensor ► Replace the unit� electronics� Backup function of the sensor activated, ►...
  • Page 17: Technical Data

    Fnr Type of fault Corrective measures Supply voltage outside the operating ► Check the supply voltage; ensure a voltage range� correct voltage supply� Operating temperature of the electronics ► Check the temperature of the upper outside the specified range� part of the unit� ►...

This manual is also suitable for:

Tad 81 series

Table of Contents