Specifications - Ryobi EBS-9576V User Manual

BELT SANDER -MANUAL
GB
F D E
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read through
this OWNER'S MANUAL and SAFETY INSTRUCTIONS
before using the product.

SPECIFICATIONS

EBS-7576
Input 230 V~50 Hz 230 V~50 Hz
Power 750 W
No load speed 250 m/min
Belt size 76x457 mm
Net weight 3.1 kg
Be sure to check the nameplate on the product,
because the voltage is subject to change depending
on the area in which the product is to be used.
DESCRIPTION
EBS-7576
1. Front handle
2. Sanding belt
3. Tension release lever
4. Rear handle
5. Dust bag
6. Dust point
EBS-9576V / 1310V
11. Front handle
12. Sanding belt
13. Tension release lever
14. Rear handle
15. Dust bag
16. Dust point
17. Lock-on button
18. Switch
19. Tracking knob
INSTRUCTIONS FOR SAFE HANDLING
WARNING!
When using electric tools, basic safety
precautions, including the following, should
always be followed to reduce the risk of fire,
electric shock and personal injury.
Keep work area clean. Cluttered areas and benches
invite injuries.
Consider work area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area lit. Do not use
power tools where there is risk to cause fire or shock.
4/08/03 9:30 Page 5
I P NL S
English
EBS-9576V EBS-1310V
110/230 V~50 Hz
950 W 1350 W
240-400 m/min 240-400 m/min
76x533 mm 100x610 mm
5.0 kg 6.4 kg
7. Lock-on button
8. Switch
9. Tracking knob
10. Front roller
22. Rear roller
24. Adjustment knob
25. Slot holder
20. Speed dial
21. Front roller
23. Rear roller
24. Adjustment knob
25. Slot holder
DK N FIN GR H
Guard against electric shock. Avoid body contact
with earthed or grounded surface (e.g. pipes,
radiators, ranges, refrigerators).
Keep children away. Do not let visitors touch the tool
or extension cord. All visitors should be kept from area.
Store idle tools. When not in use, tools should be
stored in a dry, high or locked up place, out of reach
of childen.
Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use tools for purposes not intended.
Dress properly. Do not wear loose clothing or
jewellery, they can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear protecting
hair covering to contain long hair.
Use safety glasses. Also use face or dust mask if
the cutting operation is dusty.
Do not abuse the cord. Never carry the tool by the
cord or yank it to disconnect it from the socket.
Keep the cord away from heat, oil and sharp edges.
Do not overreach. Keep proper footing and balance
at all times.
Maintain tools with care. Keep tools clean for better
and safer performance. Inspect tool cord periodically
and if damaged have it repaired by an authorized
service facility. Inspect extension cords periodically
and replace, if damaged. Keep handles dry,
clean and free from oil and grease.
Remove adjusting
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
Avoid unintentional starting. Do not carry a
plugged-in tool with a finger on the switch. Ensure
switch is off when plugging in.
Use outdoor extension leads. When tool is used
outdoors, use only extension cords intended for
outdoor use.
Stay alert. Watch what your doing. Use common
sense. Do not operate tool when you are tired.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment breakage of parts, mounting and any other
conditions that may affect its operation. Have
defective switches replaced by an authorized service
facility. Do not use the tool if the switch cannot turn it
on and off.
5
CZ RUS RO PL
keys and wrenches.