Table of Contents
Related Manuals for Whale Dry-Deck 20 SDP073R
Summary of Contents for Whale Dry-Deck 20 SDP073R
- Page 1 Dry-Deck 20 Installation Instructions Installation guidelines for Model Number SDP073R Dry Deck 20 Give booklet to customer after installation and demonstration of product use. See rear cover for list of parts contained in the kit.
- Page 2 Thank you for purchasing this Dry-Deck 20 product. Whale is the market leader in pumped shower drainage kits. These kits have the reputation of working reliably for many years without requiring maintenance. The front cover shows the product installation in an apartment with the components in an adjacent room accessed via a cupboard.
-
Page 3: Table Of Contents
Installation Warnings Contents Warnings Pump Installation Plumbing Before installation read the instructions. Plumbing of Waste Pipe • All electrical and mechanical components Plumbing Gulley (control unit, surge damper, pump and flow Control Unit sensors) must be accessible after installation. Schematic of Dry-Deck Components Flow Sensor Connection •... -
Page 4: Pump Installation
Pump Installation Before mounting the pump refer to the plumbing diagram opposite for maximum pipe specification. Mount the pump on a solid wall to prevent vibration. Use a back board if this is not possible. Note: If mounted to a stud wall pump vibration may cause noise through the resonance of the wall. -
Page 5: Plumbing Of Waste Pipe
Plumbing of Waste Pipe Inlet and Outlet pipe must always be in 22mm. Min 1:40 fall Horizontal to waste pipe - To increase pump life ensure that 1 ⁄ ” or 1 ⁄ ” pipe is used with a gravity fall where the pipe length is greater than 1m. -
Page 6: Plumbing Gulley
Plumbing Gulley Gulley Options: For conventional gulley options for wet floor and walk in showers see page 22 and 23. Note: The Gulley must be purchased separately from your distributor. Use silicone on top of the seal to ensure proper sealing beneath the tray. Using the hand tool provided to tighten the locking ring. -
Page 7: Control Unit
Control Unit Location of Control Unit: Tighten all cable entry grommets, even unused ones, to seal the Control Unit. Locate the control unit outside the showering area in accordance with BS7671: 2008 Part Connect Control Unit to 240V a.c. supply via 7 (17th Edition). -
Page 8: Schematic Of Dry-Deck Components
Schematic of the Dry-Deck Components... -
Page 9: Flow Sensor Connection
Flow Sensor Plumbing Connection Sika sensor Flow Sensor • Fit the flow sensors with the arrow in the direction of flow to the shower, downstream of any other connections to the water supply. • Ensure flow sensor is accessible. • The flow sensors must be mounted in a straight length of unstressed pipe. -
Page 10: Electrical Connections
Flow Sensor Electrical Connections • Switch off the power to the control unit Sika sensor Connections before making connections. • Feed wires through cable grommets prior to connection to the control unit. • Strip wires 10mm and twist prior to inserting into spring loaded contracts. -
Page 11: Pump Setup
Pump Set Up 3. Pump Speed: A simple set up is all that is required for trouble-free efficient performance of the Dry-Deck 20 system. 1.10 This sets the speed of the pump in relation to the flow rate from the sensors. Prior to making adjustments turn the shower on and wait until the pump runs. - Page 12 Pump Set Up (contd.) 4. Pump Speed - Fine Setting: To set the Auto Sense value select this mode, turn off the shower. This setting is required to fine tune the speed at flow rates other than that used to set the main flow rate.
- Page 13 Pump Set Up (contd.) 7. Purge Cycle: Standby Time of Pump P u r g e C y c l e S e l e c t S t a n d b y n e x t < > m i n C y c l e 1 2 3 4 5 6 h r s...
-
Page 14: Flow Restriction
Pump Operation 1.11 The Whale pump uses a single membrane to pump the water away. On the suction stroke, water 1.12 and debris are drawn in through the inlet valve. -
Page 15: Auxilary Functions
Auxilary Functions 1.12a Solenoid Switch: Specification for 12V dc Solenoid Driver See diagram 1.13. Transformer The Solenoid SW terminals are to provide water shut off to the shower by the use of an additional Part No: SDA421T momentary contact switch and auxiliary solenoid Solenoids (Not Supplied with kit) drive transformer. -
Page 16: Pump Run Switch
1.12b Pump Run Switch: See diagram 1.14. The pump run SW terminals are provided as a means by which the pump can temporarily be operated, without the shower operating, using an additional momentary contact switch. When the momentary contact switch is pressed the pump runs for 2 minutes then enters the over run cycle. -
Page 17: Plumbing Of Waste Pipe
1.13 Where the situation demands or if the waste 1.16 From pump pipe run is greater than that specified for the Whale pump a macerator pump may be used. Contact the technical helpline (0845 0694 253) for advice. The discharge from the pump must go into the top of the macerator box and not into lower side entries. - Page 19 Notes...
-
Page 20: Declaration Of Conformity
WHALE® is a registered compatibility. trademark of Munster Simms Engineering Limited. Requirements for household appliances, electric Whale’s policy is one of continuous improvement and tools and similar apparatus. Emission we reserve the right to change specifications without EN 55014-2:1997/A1:2001 Electromagnetic prior notice. -
Page 21: Component Dimensional Diagrams
Control Unit - SDS273T 204 mm Pump - SDS041T Surge Damper - 755.228... - Page 22 Tiled Floor Gulley - AK1615 90mm Gulley (Tray Thickness 5-13mm) - AK1695 90mm Gulley (Tray Thickness 20-29mm) - SDA001T...
- Page 23 Linear Gulley (Example) Vinyl Floor Gulley - AK1610 50mm Gulley - 755.140...
-
Page 24: Dry Deck 20 Components
Warranty Statement 181.148 Diaphragm Service Kit SDS061T Insert Flow Sensor Extension Kit 3 m SDS281T Contact Details Whale 2 Enterprise Road, Bangor, Co. Down, BT19 7TA. N.Ireland. Technical Helpline: 0845 0694 253 whalepumps.com dry-deck@whalepumps.com tel: 028 9127 0531 fax: 028 9146 6421...