Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ROHDE & GRAHL xio move M
Summary of Contents for ROHDE & GRAHL xio move M
- Page 1 ® move M M A N U A L E n g l i s h...
-
Page 2: Table Of Contents
Introduction Congratulations to your ROHDE GRAHL- workstation. This user manual refers to the desk-system: xio®move M. The description explains the complex equipment. The following equipments are optional: LUD hand switch, ISP- collision protection, horizontal cable duct, vertical cable duct, panels, CPU- and printer- holder. - Page 3 ® move M...
-
Page 4: Preface
Preface Dear customer. Thank you for choosing a electrically height- adjustable desk from ROHDE GRAHL GmbH. You are now in possession of a state-of-the-art product that complies with all relevant safety requirements. Intended use The control units of xio® move M may only be used for control electric height-adjustable desks. Only motors that meet with ROHDE GRAHL GmbH specifications may be used to drive the lifting devices. -
Page 5: Isp ( Intelligent System Protection)
Collision protection ISP (Intelligent System Protection) - option ISP is an electronic state-of-the-art protection system, which reduces the risk for fingers being trapped or pinched substantially. DANGER: In spite of ISP being in place, there may still be a risk of pinching in exceptional cases, as it is not only the control unit, but also the interaction between the mechanical and electronic systems that is responsible for cutting out the motor. -
Page 6: General Safety Instructions
General safety instructions CAUTION: - Do not open the xio® move M control unit under any circumstances! There is a danger of electric shock. - The xio® move M control unit is not designed for continuous operation. Changing the desktop position without interruption must not exceed the duty cycle indicated on the nameplate! - The xio®... - Page 7 DANGER: - In the event of a fault (motor or component), whenever the desktop attempts to adjust the height it may move slightly before the safety cut-out is triggered. Please note that there is a potential risk of pinching in this case. - When changing the desktop position, there may in exceptional cases be a risk of pinching in spite of the safety features.
-
Page 8: Overview Hand Switch
Hand Switches Overview LU-Hand Switch (firm) with two keys. Table-UP key Table-DOWN key LUD- hand switch (extensible) with 9 push buttons and digital information display. 2nd Motor- Information Altitude Information Table-UP key group „UP“ lights display lights 2nd Motor- Save button Table-DOWN key group „DOWN“... -
Page 9: Manual Reset- Second Motor Group
Manual reset DANGER: ISP is not enabled during all resets and limit position calibration. Please note that there is a potential risk of pinching in this case. Therefore you must ensure that no people or objects are located in the hazardous area or can reach into it. Manual reset of the second motor group (only LUD hand switch) NOTE:... -
Page 10: Downward Desktop Moving „Down
Downward desktop movement This function enables to adjust the desktop downwards. To change its position, proceed as follows: Press the TABLE DOWN key. Keep pressing the key until the required desktop height is reached. NOTE: The desktop will continue moving downwards until you release the key or the minimum height is reached. -
Page 11: Adjusting The Desktop To A Saved Position
Adjusting the desktop to a saved position NOTE: Availability of the double click function depends on the software configuration of the control unit OPTION A (WITHOUT DOUBLE CLICK FUNCTION) 1. Press the required memory position key (for ex. 2) and hold it down. The desktop will move until it reaches the saved position. -
Page 12: Software-Dependent Functions
Software-dependent functions NOTE: Prior to shipping, the control unit is parameterized with the software. The following functions are only available if the control unit has been configured accordingly. Key lock With the key lock function, the control unit can be protected from inputs by the hand switch which were done accidentally. -
Page 13: Container- And Shelf-Stop Positions
Container- and Shelf-stop positions These 2 features can be used to limit the movement area of the desktop (e.g. if a container is placed underneath the desktop). A container stop position can be defined in the lower half of the movement area, a shelf stop position in the upper half. -
Page 14: Drive Back (Optional)
Drive back (optional) NOTE: The function Drive Back is only active, if a pinch protection system (ISP, switches or pinch protection strips) is available and activated in software! After a safety function is triggered by ISP, the desktop automatically moves about 40 mm in the opposite direction. -
Page 15: Technical Data
Technische Daten Supply voltage EU: ..........207 - 255,4 V / 50 - 60 Hz Supply voltage US: . -
Page 16: Possible Faults And Remedies
Appendix In this section you will find detailed information on the following topics: • Possible faults and remedies • Error messages on the handswitch display • Click codes Possible faults and remedies DRIVES NOT WORKING POSSIBLE CAUSE REMEDY Power cord is not connected Plug the power cord into the control unit Drives are not connected Plug the motor cables into the control unit... -
Page 17: Error Messages On The Hand Switch Display
CONTROL UNIT OR HAND SWITCH NOT WORKING POSSIBLE CAUSE REMEDY Hand switch is not connected Plug in the hand switch Control unit is defective Contact customer service Power cord is defective Contact customer service Hand switch is defective Replace the hand switch Poor plug contact Connect the plugs properly ErrOr MESSAGES On THE HAnD SwITCH DISPlAy... - Page 18 THE DISPLAY READS “E00” AN ERROR CODE POSSIBLE CAUSE REMEDY There is an internal fault in the control unit. Proceed as indicated in the following error list. ERROR CODE DESCRIPTION REMEDY Defect Channel 1 Unplug the control unit. Fix the external short circuit.
- Page 19 ERROR CODE DESCRIPTION REMEDY Plug detection in M1 motor socket Plug detection in M2 motor Plug in the correct motor to the socket motor socket that shows the error. Reset all motors. Plug detection in M3 motor socket Actuator changed Synchronization lost motor Remove load from desktop.
-
Page 20: Click Codes
Click codes When the xio® move M is switched on, the control unit uses its relays to inform the user acoustically about the system state and the reason why the control unit was switched off before. The table below shows which number of clicks corresponds to certain information. NUMBER OF CLICKS STATE INFORMATION Normal operation:... -
Page 21: Further Information
Further information 9.1 END OF LIFE DISPOSAL When you no longer require the xio® move M control unit, please note the following for disposal: NOTE: The xio® move M motor control box is electrical or electronic equipment according to directive 2002/96/EC and is therefore marked with the symbol depicted on the left. NOTE: Ensure eco-friendly disposal of all the control unit components (separate the plastic and electronic parts for collection). -
Page 22: Definition
Definition “xio® move” Table top (form varies depending on the model) Cable tray (optional) Cross-braced frame Lifting column (number varies depending on the model) Hand switch (design varies depending on the model) Runner Ergonomic height adjustment In addition to plenty of exercise and changing of posture, pay attention to the following setting options for an ergonomic working posture. - Page 24 ROHDE GRAHL GmbH 31595 Steyerberg/ Voigtei Büroeinrichtungen. Made in Germany. Telefon + 49 (0) 57 69 . 7- 0 Telefax + 49 (0) 57 69 . 3 33 www.rohde-grahl.com info@rohde-grahl.de...