Rs485 12-channel shutter contact for flush mounting (36 pages)
Summary of Contents for HomeMatic CCU2 HM-Cen-O-TW-2 Series
Page 1
Montage- und Inbetriebnahmeanleitung (S. 2) Installation and operating manual (p. 27) Zentrale CCU2 Central Control Unit CCU2 HM-Cen-O-TW-x-x-2...
Inhaltsverzeichnis Hinweise zu dieser Anleitung ..........4 Gefahrenhinweis ..............4 Allgemeine Systeminformation zu Homematic ...... 6 Allgemeine Hinweise zum Funkbetrieb ........6 Funktion ................. 7 Übersicht und Anschlüsse ............8 Inbetriebnahme ..............9 Wandmontage ................ 9 Zentrale mit dem Netzwerk verbinden ......... 10 Zentrale an die Stromversorgung anschließen ....
Hinweise zu dieser Anleitung Hinweise zu dieser Anleitung Lesen Sie diese Anleitung sorgfältig, bevor Sie Ihre Homematic Komponenten in Betrieb nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf! Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben Sie auch diese Bedienungsanleitung.
Page 5
Gefahrenhinweis Aus Sicherheits- und Zulassungsgründen (CE) ist das eigenmächtige Umbauen und/oder Verändern des Gerätes nicht gestattet. Betreiben Sie das Gerät nur in Innenräumen und setzen Sie es keinem Einfluss von Feuchtigkeit, Vibrationen, ständiger Sonnen- oder anderer Wärmeeinstrahlung, Kälte und keinen mechanischen Belastungen aus. Das Gerät ist kein Spielzeug! Erlauben Sie Kindern nicht damit zu spielen.
Allgemeine Systeminformation zu Homematic Allgemeine Systeminformation zu Homematic Dieses Gerät ist Teil des Homematic Haussteuersystems und arbei- tet mit dem bidirektionalen Homematic Funkprotokoll. Alle Geräte werden mit einer Standardkonfiguration ausgeliefert. Darüber hinaus ist die Funktion des Gerätes über eine Software konfigurierbar. Welcher weitergehende Funktionsumfang sich damit ergibt, und welche Zusatzfunktionen sich im Homematic System im Zusammenspiel mit weiteren Komponenten ergeben, entnehmen Sie bitte dem Homematic WebUI Handbuch.
Funktion Funktion Die Homematic Zentrale CCU2 übernimmt als zentrales Element des Homematic-Systems vielfältige Steuer-, Kontroll- und Konfigu- rationsmöglichkeiten für alle Geräte in Ihrer Installation. Die Bedienung der Zentrale erfolgt komfortabel am PC über die Homematic Bedienoberfläche WebUI, für die Sie lediglich einen Standard-Webbrowser benötigen. Die Bedienoberfläche WebUI bietet vielfältige Funktionen für Ihre Homematic Installation: • Konfiguration und Bedienung von Homematic Geräten, • Abfrage von Statusinformationen der Homematic Geräte im Haus, •...
Inbetriebnahme Inbetriebnahme Wandmontage Bitte verwenden Sie für die Wandmontage die zwei mitgelieferten Schrauben und Dübel. Stellen Sie bei der Auswahl des Montageortes und beim Bohren in der Nähe vorhandener Schalter oder Steckdosen sicher, dass in der Wand keine Leitungen verlaufen. Montieren Sie die Zentrale nicht in der Nähe anderer Störquellen (z.
Inbetriebnahme Zentrale mit dem Netzwerk verbinden • Ziehen Sie zunächst die Abdeckkappe nach oben von der Zen- trale ab. • Schließen Sie die Zentrale mit dem mitgelieferten Netzwerkkabel (I) an Ihren DSL-Router bzw. an Ihr Kabelmodem an.
Systemanforderungen Zentrale an die Stromversorgung anschließen Um Schäden am Gerät zu vermeiden, benutzen Sie ausschließlich das mitgelieferte Originalnetzteil der CCU2 für die Stromversorgung (5V / 1500 mA). • Schließen Sie das beiliegende Netzteil (F) an die Zentrale an und stecken Sie es in die Steckdose. Das Gerät darf nur an eine frei zugängliche Netz-Steckdose angeschlossen werden.
• Nachdem die Zentrale mit dem PC, dem Router und der Span- nungsversorgung verbunden wurde, öffnen Sie Ihren Webbrow- ser. • Geben Sie die IP-Adresse Ihrer Zentrale in Ihren Browser ein (s. „8.2 IP-Adresse Ihrer Homematic Zentrale“ auf Seite 13). Anschließend gelangen Sie auf die Startseite Ihrer WebUI.
Erster Start der WebUI Bedienoberfläche IP-Adresse Ihrer Homematic Zentrale Mithilfe einer Homematic Zusatz-Software können Sie sich die IP-Adresse Ihrer Zentrale anzeigen lassen. Zum Download der Soft- ware gehen Sie wie folgt vor: • Öffnen Sie die Website www.homematic.com. • Laden Sie sich im Downloadbereich die Zip-Datei des Tools „Homematic Netfinder“ herunter und entpacken Sie alle drei...
Page 14
Erster Start der WebUI Bedienoberfläche Wenn Sie keine Internetverbindung haben, müssen Datum und Uhrzeit manuell eingestellt werden. Dafür gehen Sie wie folgt vor: • Klicken Sie in der Bedienoberfläche auf Einstellungen Systemsteuerung. • Klicken Sie anschließend auf „Zeit- und Positionseinstellung“.
Erster Start der WebUI Bedienoberfläche • Stellen Sie im nächsten Fenster das Datum und die Uhrzeit ein und klicken Sie auf „Uhrzeit übernehmen“. Alternativ können Sie die Uhrzeit vom PC übernehmen. Klicken Sie dafür auf „Zeit vom PC übernehmen“. • Klicken Sie anschließend auf „Zurück“. Updates installieren Bevor Sie Ihre WebUI nutzen können, prüfen Sie Ihr System auf verfügbare Updates und installieren Sie diese.
Page 16
Erster Start der WebUI Bedienoberfläche Um ein Update zu installieren, gehen Sie wie folgt vor: • Klicken Sie in der Bedienoberfläche auf Einstellungen Systemsteuerung. • Klicken Sie anschließend auf „Zentralen-Wartung“.
Page 17
Erster Start der WebUI Bedienoberfläche • Führen Sie im Feld „Software-Update“ die Schritte 1-4 durch: • Schritt 1: Klicken Sie zunächst auf den Button „Herunterladen“, um die Software-Installationsdateien auf Ihrem PC zu speichern. • Schritt 2: Wählen Sie die heruntergeladene Software aus. • Schritt 3: Klicken Sie auf „Hochladen“, um die Software auf Ihre Zentrale zu laden.
Sie die notwendigen Dateien für ein Update im Downloadbereich der Website www.homematic.com herunterladen und anschließend installieren. Geräte anlernen und System konfigurieren Ihre Homematic Zentrale ist jetzt für das Anlernen von Geräten be- reit. Anschließend können Sie Ihre Geräte über die WebUI steuern und konfigurieren, direkt mit anderen Geräten verknüpfen oder in Zentralenprogrammen einsetzen. Einzelheiten hierzu entnehmen Sie bitte der WebUI Bedienungsanleitung (zu finden im Download- bereich der Website www.homematic.com).
Page 19
Rück- und Fehlermeldungen durch die Geräte-LED Rück- und Fehlermeldungen durch die Geräte-LEDs Power Internet Info Zustand Fehlerbehebung Hardware startet falls dieser Zustand nicht verlassen wird, starten Sie das Recovery System (vgl. Abschnitt 10.2) Systemstart läuft blinkt falls dieser Zustand nicht verlassen schnell wird, starten Sie das Recovery System (vgl.
Hinweise zur Störungsbeseitigung 11 Hinweise zur Störungsbeseitigung 11.1 Anschluss per USB-Kabel Sollten Sie Ihre Zentrale ohne Netzwerkverbindung nutzen, können Sie das Gerät über ein USB-Kabel mit Ihrem PC verbinden. Dazu werden zusätzliche Gerätetreiber benötigt. Um diese zu installieren, gehen Sie wie folgt vor: •...
Hinweise zur Störungsbeseitigung • Geben Sie anschließend die URL „10.101.82.51“ in Ihren Inter- netbrowser ein und Sie gelangen auf die WebUI Bedienoberflä- che. 11.2 Recovery System Das Rettungssystem (Recovery System) wird nur benötigt, wenn die Software der Zentrale beschädigt wurde. Dies kann beispiels- weise auftreten, wenn während eines Software-Updates die Strom- versorgung unterbrochen wurde.
Page 22
• Die Zentrale startet jetzt das Recovery System. Die Geräte-LEDs bleiben zunächst für 10 Sekunden aus. Nachdem das Recovery System gestartet wurde, blinken alle LEDs gleichzeitig. • Über die Eingabe der Adresse „http://homematic-ccu2“ in Ihrem Webbrowser gelangen Sie auf die Startseite des Recovery Systems.
36 Sekunden in einer Stunde). Die Geräte dürfen bei Erreichen des 1 %- Limits nicht mehr senden, bis diese zeitliche Begrenzung vorüber ist. Gemäß dieser Richtlinie, werden Homematic-Geräte zu 100 % normenkonform entwickelt und produziert. Im normalen Betrieb wird der Duty Cycle in der Regel nicht vollstän- dig ausgenutzt.
Erweiterung der Speicherkapazität funkintensive Anlernprozesse der Fall sein. Eine Überschreitung des Duty Cycle Limits wird durch Blinken Ihres Homematic-Gerätes angezeigt und kann sich durch temporär fehlende Funktion des Gerätes äußern. Nach kurzer Zeit (max. 1 Stunde) ist die Funktion des Gerätes wiederhergestellt.
Wasser angefeuchtet werden. Verwenden Sie keine lösemittelhaltigen Reinigungsmittel, das Kunststoffgehäuse und die Beschriftung kann dadurch angegriffen werden. 14 Lieferumfang • Homematic Zentrale CCU2 • Steckernetzteil (Ausgangsspannung 5V , 1500 mA) • Montagematerial (2x Schrauben, 2x Dübel) • USB-Kabel •...
Page 26
Technische Daten Umgebungstemperatur: 5 bis 35 °C Lagertemperatur: -20 bis +60 °C Abmessungen (B x H x T): 116 x 150 x 34 mm Gewicht: 165 g Funkfrequenz: 868,3 MHz/869,525 MHz Empfängerkategorie: SRD Category 2 Typ. Funk-Freifeldreichweite: 400 m Duty Cycle: <...
Page 28
Connecting the Central Control Unit to the power supply ..36 System requirements ............36 Starting the WebUI user interface for the first time ....37 Calling up WebUI ..............37 IP address of your Homematic Central Control Unit .... 38 Setting the date and time ............. 38 Installing updates ..............40 9.5 Teaching in devices and configuring the system ....43 Information and error messages indicated by the device LEDs .................
Information about this manual Information about this manual Read these instructions carefully before starting to use your Home- matic components. Keep the manual so you can refer to it at a later date if you need to. If you hand over the device to other persons for use, please hand over the operating manual as well.
Page 30
Hazard information For safety and licensing reasons (CE), unauthorized change and/or modification of the device is not permitted. The device may only be operated indoors and must be protected from the effects of moisture, vibrations, solar or other methods of heat radiation, cold and mechanical loads. The device is not a toy; do not allow children to play with it. Do not leave packaging material lying around. Plastic films/ bags, pieces of polystyrene, etc.
General system information about Homematic General system information about Homematic This device is part of the Homematic home control system and works with the bidirectional BidCoS wireless protocol. ® All devices are supplied with a standard configuration. The function- ality of the device can be configured using software. The additional functions that can be made available in this way and the supple-...
Function Function The Homematic CCU2 Central Control Unit is the central element of your Homematic system, offering a whole range of control, monito- ring and configuration options for all the devices in your installation. The Central Control Unit is easy to operate using the Homematic user interface, WebUI, on your PC, for which you only need a stan- dard web browser.
Overview and connections Overview and connections Micro-SD Power Internet Info (A) Power LED (B) Internet LED (C) Info LED (D) Recovery button (E) microSD/SDHC card slot Power supply cable (G) USB device interface (H) USB host interface Network cable...
Start-up Start-up Wall mounting Please use the two screws and plugs supplied for wall mounting. When selecting a mounting location and drilling in the vicinity of switches or socket outlets, make sure that there are no cables in the wall. Do not mount the Central Control Unit in the vicinity of other sources of interference (e.g.
Start-up Connecting the Central Control Unit to the network • First pull the cap up and off the Central Control Unit. • Connect the Central Control Unit to your DSL router or cable modem using the network cable supplied (I).
System requirements Connecting the Central Control Unit to the power supply For the power supply, only use the CCU2 original power supply unit (5 V DC/1500 mA) delivered with the device in order to avoid damaging the device. • Attach the supplied power supply unit (F) to the Central Control Unit and plug it into the socket outlet.
• Please enter the IP address of your Central Control Unit into the browser (see „9.2 IP address of your Homematic Central Control Unit“ on page 38). You will then be taken to the homepage of your WebUI.
Starting the WebUI user interface for the first time IP address of your Homematic Central Control Unit You can use additional Homematic software to display the IP address of your Central Control Unit. To download the software, proceed as follows: • Open the website www.homematic.com. • Download the zip file of the “Homematic Netfinder” tool from the downloads area and unzip all three files at the desired location (e.g.
Page 39
Starting the WebUI user interface for the first time If you do not have an Internet connection, the date and time must be set manually. To do this, proceed as follows: • Click on Settings Control Panel in the user interface. • Then click on “Time and position“.
Starting the WebUI user interface for the first time • Set the date and time in the next window and click on “Apply time”. Alternatively, you can import the time from the PC. To do this, click on “Get time from computer”. • Then click on “Back”. Installing updates Before you can use your WebUI, you must check your system for available updates and install them.
Page 41
Starting the WebUI user interface for the first time To install an update, proceed as follows: • Click on Settings Control Panel in the user interface. • Then click on “CCU maintenance”.
Page 42
If you are using your Central Control Unit without an Internet connection, the homepage of your WebUI will show you whether you are using the most up-to-date version. If you are not, you can download and then install the files required for an update from the Downloads area of the www. homematic.com website.
Information and error messages indicated by the device LEDs Teaching in devices and configuring the system Your Homematic Central Control Unit is now ready for devices to be taught-in. You will then be able to use WebUI to control your devices, configure them, connect them directly to other devices, or use them in central programs. Please refer to the WebUI operating manual for more details (you can find this in the Downloads area of the website www.homematic.com).
Page 44
Information and error messages indicated by the device LEDs Information and error messages indicated by the device LEDs Power Internet Info State Remedy Hardware starts If the LED does not exit this state, start the recovery system (see Section 10.2) System start is Flashing If the LED does not exit this state, running quickly start the recovery system (see...
Notes on rectifying malfunctions 11 Notes on rectifying malfunctions 11.1 Connection via USB cable If you are using your Central Control Unit without a network con- nection, you can connect the device to your PC using a USB cable. Additional device drivers are required to do this. To install these, proceed as follows: •...
Notes on rectifying malfunctions • Then enter the URL “10.101.82.51” into your Internet browser and you will be taken to the WebUI user interface. 11.2 Recovery system The recovery system is only required if the software of the central control system has been damaged. This can happen, for example, if the power supply is interrupted during a software update.
Page 47
• The Central Control Unit now starts the recovery system. The de- vice LEDs remain off for 10 seconds initially. Once the recovery system has been started, all LEDs flash at the same time. • Entering “http://homematic-ccu2” in your web browser will take you to the homepage of the recovery system. • First download the latest installation file for the software from the Downloads area of the website www.homematic.com.
1% of an hour (i.e. 36 seconds in an hour). Devices must cease transmission when they reach the 1% limit until this time restriction comes to an end. Homematic devices are designed and produced with 100% conformity to this regulation.
Do not use any detergents containing solvents, as they could corrode the plastic housing and label. 14 Scope of supply • Homematic CCU2 Central Control Unit • Plug-in power supply unit (output voltage 5 V DC, 1500 mA) • Mounting accessories (2x screws, 2x plugs) •...
Technical data 15 Technical data Short name: HM-Cen-O-TW-x-x-2 Supply voltage plug-in mains adapter (input): 100 - 240 V AC, 50/60 Hz Power consumption plug-in mains adapter: 7.5 W max. Supply voltage: 5 VDC Current consumption: 1200 mA max. Protection class: III (safe extra-low voltage) Degree of protection: IP20...
Page 51
Technical data Instructions for disposal Do not dispose of the device with regular domestic waste. Electronic equipment must be disposed of at local collection points for waste electronic equipment in compliance with the Waste Electrical and Electronic Equipment Directive. The CE Marking is simply an official symbol relating to the free movement of a product;...
Page 52
Bevollmächtigter des Herstellers: Manufacturer’s authorised representative: eQ-3 AG Maiburger Straße 29 26789 Leer / GERMANY www.eQ-3.de...