Assa Abloy RIXSON W50 Installation Instructions

Closer Adjustment
+
BACK
CHECK
LATCH
F
Closing speeds can be adjusted to suit local conditions and
requirements. Label on closer face designates the purpose
of each adjustment screw. Adjustments are for speed
control.
Repairs, parts replacement or internal adjustments must be done by a Rixson authorized repair agency. Consult www.rixson.com
for an authorized repair agency in your area.
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2005, 2009, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Rixson Specialty Door Controls
-
DELAY
F
S
STROKE
F S
S
A. The stroke valve allows adjustment from open to 15°.
B. The latch valve allows adjustment from 15° to closed
position.
C. IMPORTANT: Back check valve option must be adjusted
to vary resistance from light to firm at 70° of door
opening.
D. The delay valve option allows closing speed adjustment
from open position to 65°.
866-474-9766 Technical Department
www.rixson.com
RIXSON
PAGE 4
ASSA ABLOY
Template
1-7/16
1-1/32
3/4
1/8 2-5/8
2-3/4
Jamb
2-5/8 R.
Max.
1/8 2-5/8
2-1/4*
Shim
Provide
3/8" Dia.
Hole
2-3/4
C L Spindle
2-3/32
1-25/32
9/32
9/16
RIXSON
1-19/32
®
WOOD DOOR ARM PLATE
ASSA ABLOY
Conversion from inches to metric: inch x 25.4.
Rixson Specialty Door Controls
®
Installation Instructions
50W (06-09)
7/8 Dia.
9/16
21/32
9/32
1/4-20 x 5/8" FHMS or
#14 x 1/2" FHWS
1/16
1/4
Finish Plate
1-1/4 Dia.
TOP PIVOT
C L Spindle
Arm
Floor Plate
19-1/4
9*
*Mortised
7-7/16
7/16
Wood Door
Arm Plate
Use Top
Arm Plate
(2) Holes
Spindle Shoulder Collar
Fasten Front
Mounting
Cement Case
Screws First
19-1/8
#14 x 2-1/2" FWHS
4-7/32
(6 Places)
1-7/32
See
11/16
Note 4
C L
1-3/8
Door
1-13/32
6-7/32
10-1/2
www.rixson.com
W50 Floor Closer
Center Hung
Single or Double Acting
Non-Handed
Wood Door Installation
6-3/4
1-15/32
9/32
9/32
15/32
JAMB PORTION
1-5/16
9/32
12-24 x 5/8" FHMS or
#12 x 1-1/4" FHWS
(2 Places) 1/4-20 x 5/8" FHMS or
#14 x 1-1/2" FHWS
5/8 1-1/8
(2 Places)
DOOR PORTION
1-1/4
4-13/16
5/8
5-9/32
1-3/8" Min. Clearance
Required for Arm, Arm
Provide 9/16
Plate H and Shims
Dia. Hole for
Door Mortised
Alignment
1-7/8" Deep
Screw
for Arm
(2 Places)
4-1/2
1-1/4
Floor
Plate
3/16
Cement Case
4-3/8
WITH FLOOR PLATE
Set Cement Case Flush
with Finished Floor
Provide 9/16
Door Mortised
A
Dia. Hole for Deep for Arm
Alignment
1/4 Threshold 1-3/4
Screw
1/2 Threshold 1-1/2
(2 Places)
3/16
B
A
2
3/16
Threshold
WITH THRESHOLD
Set Cement Case Flush
Tighten Spindle with Finished Floor
Screw Firmly
Notes:
Arm
1. Do not scale drawing.
2. Suitable reinforcing by others.
3. Rixson design threshold available on request.
4. Tighten adjusting screw to notched "V" line
Spindle
on arm to acquire standard initial location
of door. Screw moves door towards and
away from jamb to equalize door clearances.
5. Auxiliary stop required.
6. All dimensions given in inches.
866-474-9766 Technical Department
B
1-1/8
7/8