Output Definitions - ADT Safewatch Pro 3000 Programming Manual

✱

80 OUTPUT DEFINITIONS

Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you
enter the data during the displays and prompts that appear in sequence.
Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes.
2. For Powerline Carrier devices (plcd), field
3. Tampers of expansion units cannot be used to operate devices.
Output Activation Type and Detail
Function
Activated by Zone List
Number
0=delete (ZL)
(1-48)
1=zn list 1-8 = list
2=zn type
3=zn no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
ZONE TYPE/SYSTEM OPERATION – Choices for Zone Types are:
00 = Not Used 05 = Trouble Day/Alarm Night
01 = Entry/Exit#1 06 = 24 Hr Silent
02 = Entry/Exit#2 07 = 24 Hr Audible
03 = Perimeter 08 = 24 Hr Aux
04 = Interior Follower 09 = Fire
Choices for System Operation are:
20 = Arming–Stay
21 = Arming–Away
22 = Disarming (Code + OFF)
31 = End of Exit Time
32 = Start of Entry Time
33 = Any Burglary Alarm
36 = **At Bell Timeout***
Partition
Number
Zone Type Zone No.
(P)
(ZT) (ZN)
(if using ZT trig)
(see table 00=none
0 = any
below) 01-64
1 = partition 1
2 = partition 2
3 = common
10 = Interior w/Delay
12 = Monitor Zone
14 = Carbon Monoxide
16 = Fire w/Verification
23 = No Alarm Response
38 = Chime 52 = Kissoff
39 = Any Fire Alarm 54 = Fire Zone Reset
40 = Bypassing 58 = Duress
41 = **AC Power Failure 60 = AAV Trigger
42 = **System Battery Low 66 = Function key†
43 = Communication Failure 67 = Bell Failure
68 = TELCO Line Fault
78 = keyswitch red LED†††
79 = keyswitch green LED†††
✱
27 must be programmed with a House Code.
Event (for zone list/activated by)
By Zone List By Zone No.
0 = restore 0 = restore
1 = alarm 1 = alrm/flt/trbl
2 = fault
3 = trouble
24 = Silent Burglary
25 = 24-Hr Non-Alarm
77 = Keyswitch
90-93 = Configurable
** Use 0 (any) for Partition No. (P) entry.
*** Or at Disarming, whichever occurs earlier.
† Use *57 Menu mode to assign the function key.
†† Duration is set in program field *177.
††† Device action not used for these choices.
– 11 –
Action Output
0 = off Number
1 = close 2 secs
2 = stay closed 1-18= dev
3 = pulse
4 = toggle
5 = duration 1
††
6 = duration 2
††
Note: Any zone in "ZT" going into alarm,
fault, or trouble will actuate device.
Any zone of that type that restores will
stop relay action.
Note: In normal operation mode:
Code + # + 7 + NN Key Entry starts Device
Code + # + 8 + NN Key Entry stops Device
Device
Type
R = relay
T = trigger
X = X10