Initial Start-Up; Manual Operation; Automatic Operation - Lennox Traditions Freestanding P11 Installation Instructions Manual

Fuel Delivery Rate
The feed rate switch manages the fuel delivery rate by control­
ling the amount of time the auger motor will run as follows:
P fil 20-Fi ro 1 rees an mg t d"
e
Feed Rae
*Lb.'spertor
klprvtb"
SeUrg fuel deil.ey
a-.J/OFFTme
(sarrds)
Low 1 on/5.40 off 1.5 Lb.'s/hr.
=
Med. 1 on/3.30 off 2.5 Lb.'s/hr.
=
Hioh = 1 on/1. 75 off 3.8 Lb.'s/hr.
reestan ing d
P fil 30-F. ro e
1
Feed Rae *Lb.' s pertor
klprvtb"
fuel deil.ey
SeUrg a-.J/OFFTme
lsarrdsl
Low 1 on/4.50 off 1. 7 Lb.'s/hr.
=
Med. 1 on/1.90 off 2.6 Lb.'s/hr.
=
Hioh 1 on/1.15 off 4.5 Lb.'s/hr.
=
Profile 30-/nsert
Feed Rae kJPM:b" *Lb.'spertor
fuel deil.ey
SeUrg
a-.J/OFFTme
(sarrds)
Low 1 on/4.50 off 1. 7 Lb.'s/hr.
=
2.6 Lb.'s/hr.
Med. 1 on/1.90 off
=
Hioh 1 on/1.15off 4.5 Lb.'s/hr.
=
7i d"ti ra I ons P11 F. reestan ing d
-
Feed Rae kJPM:b" *Lb.' s pertor
fuel deil.ey
SeUrg 00/0FFTme
lsarrdsl
Low 1 on/5.00 off 1.5 Lb.'s/hr.
=
Med. 1 on/3. 30 off 2.5 Lb.'s/hr.
=
Hiqh 1.on/1.60 off 3.8 Lb.'s/hr.
=
*
Feed rates are approximations only. Actual feed rate will vary de­
pending on size, quality and length of fuel used and variations in
line voltage.
♦ Estimated heat input based on fuel value of 8500 BTU per lb. of fuel.
Your pellet stove can be operated in either Manual or
Automatic mode. The �anual mode is used when oper­
ating without a thermostat. The Automatic mode is used
when utilizing a wall thermostat.
Initial Start-Up/Empty Ho-p'l)�r or Feed
Tube:
During an initial start-up, or in the case where the hopper
has run out of fuel, it will be necessary to prime the auger
feed system. The control board is set to deliver fuel for
approximately 2 1/2 minutes during start-up, which, with a
fully primed auger tube, will provide the appropriate
amount of fuel for ignition.
When first starting your pellet stove, it will be necessary to
prime the auger tube. To prime the auger tube you need to
first fill the hopper with pellets, and press the ON button on
the control. Wait approximately 2 1/2 minutes and turn the
controls OFF and then back ON again. Wait an additional
2 1/2 minutes (if necessary) and continue this process until
fuel begins to fall into the burn grate. Remember, different
brand fuels feed at different rates.
Operating Instructions
Bun
♦ ApproJamcie
lime
BTUperha.r
fuel derivery
(hous)
13,000 BTU/hr 37
21,000 BTU/hr 22
32,000 BTU/hr 15
♦ Appro>Gmate Bun
BTUperha.r lime
fuel deriverv
(ha.r.s\
14,000 BTU/hr 48
22,000 BTU/hr 30
39,000 BTU/hr 18
♦ Appro>Gmate Bun
BTUperha.r lime
fuel delive!y
(hous)
14,000 BTU/hr 30
22,000 BTU/hr 20
39,000 BTU/hr 12
♦ Appro>Gmate Bum
BTUperha.r lime
fuel delivery
(ror.s\
12,000 BTU/hr 34
20
21,000 BTU/hr
32,000 BTU/hr 14
. .
'
Page 24
Once fuel starts to enter the bum grate, tum the stove OFF
and then back ON. The auger tube should now be primed and
the stove should deliver enough fuel for proper ignition. It may
be necessary to follow these procedures in the event that the
hopper runs completely out of fuel.

Manual Operation:

Pressing the stove on/off switch initiates the start-up cycle.
The green on/off light, near the top of the control, will light up
to indicate the "on" status. The fan speeds and pellet feeds
are fixed during this time to provide appropriate ignition. The
Fast-Fire igniter system will light the pellets feeding to the bum
grate, after about 3 minutes. The start-up cycle is in effect for
approximately 2 minutes after flame is detected in the bum
grate. A photo eye, located near the pellet feed tube monitors
the existence of flame. After the start-up cycle your stove will
be in the run mode. At this point the stove will operate in the
heat output and blower settings selected. These settings can
be selected either during or after the start-up cycle. Pressing
the stove on/off switch during the run mode will initiate the
shut down cycle. The on/off indicator light will tum off. The
pellets will stop feeding and the blowers will run at a fixed
speed for approximately 10 minutes. At this point your stove
is safely shut down and can ONLY be re-started by pressing
the stove on/off switch again.

Automatic Operation:

Your stove is capable of running in an automatic mode with
the use of a wall thermostat. NOTE: For the thermostat to
control the operation of the stove, the "on" status must be ac­
tive on the stove's on/off switch. The thermostat will establish
either a demand mode or a stand-by mode. The thermostat
should be set for the desired room temperature. If the room
temperature drops below the level on the thermostat the stove
will automatically begin the start-up cycle, as explained above
in the Manual Operation section. Once the start-up cycle is
completed the stove will operate in whatever heat and blower
setting you have selected. For best operation under thermo­
stat control, the Medium or High settings recommended.
When the desired room temperature is reached the stove will
automatically go into the shut down cycle. The pellet feed will
stop and the blowers will continue for a controlled time allow­
ing safe shut down of your stove. All lights will shut off when
the thermostat is open. The heat and blower settings can be
changed at any time, but only take affect during the run mode.
When the temperature in the room drops to the level set at
the thermostat, the stove will again begin the start-up cycle
and resume automatic operation in the demand mode.
NOTE: If the stove on/off switch is pressed while the thermo­
stat is in the standby mode the stove will not restart until the
thermostat closes.