Lighting; Normal Operation - LA NORDICA Giulietta Instructions For Installation, Use And Maintenance Manual

9. LIGHTING

IMPORTANT: The first time that the appliance is lit, there will be an odour given off (due to the drying of
the adhesives of the junction chord), which disappears after a short use. It must be ensured, in any
case, a good ventilation of the environment. Upon the first ignition we suggest loading a reduced
quantity of fuel and slightly increasing the calorific value of the equipment.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to
know the following information:
•
the construction materials of the involved products are not homogeneous, as matter of fact there
are simultaneously parts in cast iron and steel.
•
the temperature to which the body of the product is subject is not homogeneous: from area to area,
variable temperatures within the range of 300° C - 5 00 ° C are detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same day,
as well as to cycles of intense use or of absolute standstill when season changes;
•
the new appliance, before being considered seasoned has to be subject to many start cycles to
allow all materials and paints to complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great
thermal stress, as well as of wet paint. This paint, although during the manufacture it is backed at
250 ° C for some hours, must exceed many times and f or a given period of time the temperature of
350 ° C before becoming completely embedded in the m etallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. During the first starts, do not load excessively the combustion chamber (about half the quantity
indicated in the instructions manual) and keep the product continuously ON for at least 6-10 hours
with the registers less open than the value indicated in the instructions manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation
booklet concerning maximum load) and, if possible, keep the lighting periods long avoiding, at least
in this initial phase, short ON/OFF cycles.
5. During the first starts, no object should be leaned on the appliance and in detail on
enamelled surfaces. Enamelled surfaces must not be touched during heating.
Once the «break-in» has been completed, it is possible to use the product as the motor of a car,
6.
avoiding abrupt heating with excessive loads.
To light the fire, it is suggested using small wood pieces together with paper or other traded lighting means.
It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
Operation with wood :
Open the secondary air control Picture 2, Pos. A , A1), open the thermostat (B , B1), open the ignition
control (C), light up the fire.
After about 10 minutes, when the fire is lighted, close the thermostat (B, B1) and the ignition control (C)
and adjust the combustion course with the controls (A, A1).
The openings for air (primary and secondary) must be opened together just a little (you must open the
eventual butterfly valve placed on the pipe of smokes exhaust). When the wood starts burning, adjust the
air for combustion according to the instructions on paragraph 10.
Never overload the stove (compare the technical table - max. quantity of loadable fuel).
Too much fuel and too much air for the combustion may cause overheating and then damage the
stove, as a consequence some scratches in the lower front part of the stove could happen.
The warranty does not cover the damages due to overheating of the equipment.
10.

NORMAL OPERATION

IMPORTANT: due to the fact the door of the hearth has a remarkable size, we suggest you to open the
door very slowly, to avoid the exit of smokes.
For safety reasons the door of the hearth can be opened only for the loading of the fuel. The hearth
door must always remain closed during operation or rest.
24
GIULIETTA – ISETTA-07 – ISOTTA-07
Instructions for installation, use and maintenance – EN – Rev.04