Related Manuals for Cramer 40CS12
Summary of Contents for Cramer 40CS12
- Page 1 2000186/2000286(40CS12/40CS15) EN | DE | ES | IT | FR | PT | NL | RU| FI | SV | NO| DA| PL | CS | SK | SL| HR| EL | AR| TR | LT | LV | ET |...
- Page 2 40CS12 (2000186) 40CS15 (2000286) Fig. 1 Fig. 2 Fig. 3 Fig. 4. 50mm 50mm Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig.
-
Page 3: Product Overview
Flung out of parts of the work piece. Battery Discharging temperature Inhalation of work piece particles. 6.8 ˚F (-14 ˚C) ~ 149 ˚F (65°C) Range Skin contact with the lubrication oil. Loss of hearing, if no ear protection is used during work. cramer.eu... - Page 4 Prevent unintentional starting. Ensure the switch is in the off position Keep cutting tools sharp and clean. Properly maintained cutting tools before connecting to power source and/or battery pack and when with sharp cutting edges are less likely to bind and are easier to control. cramer.eu...
- Page 5 Always hold the chain saw with your right hand at the rear handle and Tip contact in some cases may cause a sudden reverse reaction, kicking the cramer.eu...
- Page 6 There are measures that can be taken by the operator to possibly reduce the effects of vibration: Keep your body warm in cold weather, when operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a cramer.eu...
-
Page 7: Before Operation
Wear non-slip, heavy duty gloves. 31. Keep work off ground leave support limbs until log is cut 32. Log supported along the entire length Avoid bar nose contact. 33. Cut from top (over buck) avoid cutting earth 34. Log supported one end cramer.eu... -
Page 8: Batteries And Battery Charger
When cross-cutting, pay attention to trunks standing very close to each tight. other. If possible, use a sawing trestle. After the chain is well-tensioned, tighten the nuts again. Checking the chain lubricant NOTE: The saw chain is properly tensioned if, in the middle of the guide bar, it cramer.eu... - Page 9 Always be sure of your footing and hold the chain saw firmly with both hands As the felling cut gets close to the hinge, the tree should begin to fall. If there is cramer.eu...
-
Page 10: Maintenance
Fit the bar flush against the mounting surface so that the bar studs are in the long slot of the bar. Ensure that the chain is over the sprocket. MAINTENANCE Replace the chain cover. Remove all slack from the chain by turning the chain a djustment screw cramer.eu... - Page 11 Count the number of strokes given to the cutter as a reference and file away with the same number of strokes on all other cutters. If the depth gauge protrudes from the template after sharpening a few cramer.eu...
-
Page 12: Troubleshooting
Check guide bar and saw chain saw. After all debris is chain for damage. cleared, insert battery and run the chain saw. If the sprocket is spinning your motor is okay. If the sprocket is not spinning, call customer service. cramer.eu... - Page 13 The battery and power tool Refer to the battery and charger is too hot or too cold. maintaince part in the manual. * If the fault is not solved, you must go to your distributor and/or nearest Authorized Technical Service. cramer.eu...
-
Page 14: Technical Data
< 0.2s Type Chain saw Chain oil capacity 180 ml 180 ml Brand Cramer Model 40CS12/ 40CS15 Weight without battery pack 3.6 kg 3.8 kg Serial No See product rating label Emission sound pressure 98 dB(A), K 98 dB(A), K... - Page 15 2006/42/CE Electromagnetic compatibility 2014/30/EU directive RoHS Directive 2011/65/EU Low voltage directive Annex V / 2000/14/EC Model 40CS12 40CS15 Measured sound power level 105 dB(A) 105 dB(A) Guaranteed sound power level 108 dB(A) 108 dB(A) The EC type-examination certificate number: issued by SGS United Kingdom Limited (0890).
Need help?
Do you have a question about the 40CS12 and is the answer not in the manual?
Questions and answers