Control unit for operation with constant boiler water temperature in a single boiler system or control unit for operation with constant boiler water temperature in a multi boiler system with higher ranking third party control unit (57 pages)
Boiler control unit for high temperature heating systems (8 pages)
Summary of Contents for Viessmann VITOTRONIC 100
Page 1
VIESMANN Operating instructions for the system user Control of the boiler water temperature for each boiler in the cascade: Vitotronic 100, type GC7B ■ ■ Vitotronic 100, type HC1B Weather-compensated control for a multi boiler system (cascade): Vitotronic 300-K, type MW1B ■...
Page 2
Safety instructions For your safety Please follow these safety instructions closely to prevent accidents and material losses. Safety instructions explained Danger Note This symbol warns against the risk of injury. Details identified by the word "Note" contain additional information. Please note This symbol warns against the risk of material losses and environmental pollution.
Page 3
Safety instructions For your safety (cont.) If you smell gas Danger Escaping gas can lead to explosions which may result in serious injury. ■ Do not smoke. Prevent naked flames and sparks. Do not switch lights or electrical appli- ances on or off. Close the gas shut-off valve.
Page 4
Safety instructions For your safety (cont.) Installation room requirements Danger Please note Sealed vents result in a lack of combustion air. Incorrect ambient conditions can lead to heating This leads to incomplete combustion and the system damage and can put safe operation at formation of life threatening carbon monoxide.
Page 5
3. Operating the Vitotronic Opening the Vitotronic 100 ..............11 Vitotronic 100 programming unit ............11 How to use the controls, Vitotronic 100 ..........11 Symbols on the display ................12 4. Operating the Vitotronic Opening the Vitotronic 300-K ..............13 300-K Vitotronic 300-K programming unit ............
Page 6
Rooms are too hot ................. 36 There is no hot water ................37 The DHW is too hot ................37 "OFF" is displayed at the Vitotronic 100 ..........38 " " is displayed at the Vitotronic 100 ............ 38 ë...
Page 7
No liability is accepted for losses resulting The Viessmann General Terms and Conditions apply, from inappropriate use. which are included in each current Viessmann pricelist. Liability is limited to typical damage arising if a funda- mental contractual obligation is violated through slight negligence, the fulfilment of which is essential for proper execution of the contract.
This information can be found in chapter "Terminology" in the Appendix. Intended use The device is intended to control only Viessmann Incorrect usage or operation of the appliance (e.g. the medium sized and industrial/commercial boilers with oil appliance being opened by the system user) is prohibi- or gas burners, in line with the intended use of those ted and will result in an exclusion of liability.
(cascade) perature for the heating system is specified by the Vitotronic 300-K, using weather compensation. The Vitotronic 100, type GC7B and type HC1B, is designed to control the boiler water temperature of the respective boiler in the cascade. Commissioning...
Page 10
Introductory information Operating principles (cont.) Other control devices: Remote control operating instructions If remote control units are installed in your rooms, you can also adjust the settings at the remote control units.
Scrolls through the menu or adjusts values. OK Confirms your selection or saves the setting. How to use the controls, Vitotronic 100 In multi boiler systems, each Vitotronic 100 indicates Note the boiler number on the default display. The follow- If a boiler is not operational, "OFF"...
Operating the Vitotronic 100 Symbols on the display These icons are not always displayed, but appear sub- Messages ject to the system version and the operating status. Service message Flashing displays indicate that modifications can be The service interval has expired.
Operating the Vitotronic 300-K Opening the Vitotronic 300-K The programming unit is located behind the cover flap. To open, pull the top edge of the hinged cover forward. Fig. 4 Cover flap Vitotronic 300-K programming unit Boiler sequence Boiler Common flow temp 40°C Fig.
Operating the Vitotronic 300-K Menu, Vitotronic 300-K (cont.) Standard menu Call up the standard menu as follows: The meanings of the icons are as follows: ■ If the screen saver is active (see page 14): ■ Solid white boiler: Press OK. The boiler has been enabled by the cascade control ■...
Page 15
Operating the Vitotronic 300-K How to use the controls, Vitotronic 300-K (cont.) Boiler sequence Boiler Common flow temp 40°C Menu Boiler sequence Heating Solar energy Continue with Heating circ. 1 Ù Ú Htg circ. selection Ù Ú Ù Ú Party mode ê...
Vitotronic 300-K: Central heating Required settings (central heating) This setting can only be made at the Vitotronic 300-K. Note Your contractor can, for example, enable the "Screed If you require central heating, check the following function" to dry the screed in your new building or points: extension.
Vitotronic 300-K: Central heating Setting the room temperature (cont.) 2. "Heating" 7. OK to confirm 3. OK to confirm 8. Set the required value. 4. Select the heating circuit if required (see page 16). The rooms are heated to this temperature: ■...
Vitotronic 300-K: Central heating Setting the time program for central heating (cont.) Example shown: Example: ■ Time program for Monday to Friday ("Mo-Fr") You want to set the same time program for every day except Monday: ■ Time phase From 05:00 to 08:30 Select the period "Monday Sunday"...
Vitotronic 300-K: Central heating Setting the "Heating curve" (cont.) Heating characteristics Measure Living space is too cold in spring/autumn, but warm Adjust the "Slope" of the "Heating curve" to the next enough in winter. lowest value and the "Level" to a higher value. Living space is too warm in spring/autumn, but warm Adjust the "Slope"...
Vitotronic 300-K: Central heating Reducing the room temperature temporarily (cont.) Setting "Economy mode" Extended menu 4. Select the heating circuit if required (see page 16). 5. OK to confirm 2. "Heating" 6. "Economy mode" 3. OK to confirm 7. OK to confirm Ending "Economy mode"...
Vitotronic 300-K: Central heating Energy saving function for longer absences (cont.) Display in the extended menu In the extended menu, you can check the selected "Holiday program" under "Information" (see chapter "Checking information", "Heating circuit ..." group). Cancelling or deleting a "Holiday program" 4.
Vitotronic 300-K: DHW heating Setting the DHW temperature This setting can only be made at the Vitotronic 300-K. 2. "DHW" If you want DHW heating, check the following points: 3. OK to confirm Have you set the required DHW temperature? ■...
Vitotronic 300-K: DHW heating Setting the time program for DHW heating (cont.) 07. OK to confirm Example: You want to set the same time program for every day 08. Select part of the week or a day. except Monday: Select the period "Monday Sunday"...
Vitotronic 300-K: DHW heating Setting the time program for DHW heating (cont.) DHW heating once, outside the time program Note 3. OK to confirm The "Heating and DHW" or "Only DHW" operating program must be set for at least one system heating 4.
Vitotronic 300-K: DHW heating Switching off DHW heating (cont.) You do not want DHW, but do want to heat the rooms. Extended menu 07. "Heating and DHW" until the menu is displayed. 02. Select the heating circuit if required (see page 16). 09.
Further adjustments Setting the "Boiler sequence" This setting can only be made at the Vitotronic 300-K. 2. "Boiler sequence" Depending on the set coding addresses and internal control calculations, the control unit offers various 3. Set the required boiler sequence and confirm with boiler sequences.
This setting can only be made at the Vitotronic 300-K. Extended menu 3. "Language" 4. Select the required language. 2. "Settings" Setting the "Temperature unit" (°C/°F) Vitotronic 100 Factory setting: °C 3. OK to confirm; " " flashes. Press the following keys: 4. / for the required "Temperature unit".
Further adjustments Restoring factory settings (cont.) Vitotronic 300-K You can individually restore all modified values for 2. "Settings" each heating circuit to their factory setting. 3. "Standard setting" Extended menu 4. "Heating circuit 1", "Heating circuit 2" or "Heat- ing circuit 3". System setting Settings and values that are reset "Heating circuit 1", "Heating cir-...
Checks Checking information Vitotronic 100, checks for each boiler Subject to the components connected and the settings 4. / for the required information. made, you can check current temperatures and oper- ating conditions. 5. OK to confirm; if you want to reset the value to "0"...
Vitotronic 100 If your heating system is due for a service, the symbol Notify your contractor and acknowledge the service " " flashes on the Vitotronic 100 display, and the fol- message by pressing OK. lowing displays are shown. Your contractor can select when a service should be...
Checks Checking fault messages (cont.) Example: 2. Acknowledge the fault message with OK. Symbol Fault code shown: "d1" no longer flashes. Note ã ■ If you have connected signalling equipment to indicate fault messages (e.g. a buzzer), this is deactivated when the fault message is acknowl- edged.
Page 32
Emissions test mode Emissions test mode should only be activated by your Test mode must be activated at the Vitotronic 100 of flue gas inspector during the annual inspection. the boiler to be tested and also, for heat transfer, at Emissions test mode is enabled for flue gas measure- the Vitotronic 300-K cascade control unit.
Switching on and off Control unit controls Vitotronic 100 controls Vitotronic 100, type GC7B °C Fig. 12 Fault indicator (red) Reset button ON indicator (green) ON/OFF switch Vitotronic 100, type HC1B °C Fig. 13 Fault indicator (red) ON/OFF switch ON indicator (green)
Ending the "Standby mode" operating program Select another operating program. Without frost protection monitoring (shutdown) 1. Turn off the ON/OFF switches at all Vitotronic 100 Information on prolonged shutdown and Vitotronic 300-K (see chapter "Controls"). Circulation pumps may seize up as they are not ■...
Page 35
On every Vitotronic 100, " " must be set, otherwise the Vitotronic 300-K cannot use the corresponding 5. Turn on the ON/OFF switches at all Vitotronic 100 boiler to generate heat. and Vitotronic 300-K (see chapter "Controls"). After a short time, the following is shown on the display: ■...
(see page 30). If necessary, notify your contractor. Symbol " " is displayed on the Vitotronic 100. Check the type of fault, make a note of the fault code and acknowledge the message (see page 30).
Rooms are too hot (cont.) Cause Remedy Symbol " " is displayed on the Vitotronic 100. Check the type of fault, make a note of the fault code and acknowledge the message (see page 30). If necessary, notify your contractor.
What to do if... "OFF" is displayed at the Vitotronic 100 Cause Remedy The operating program is enabled or the boiler is shut Set the operating program down externally. If necessary, notify your contractor. " " is displayed at the Vitotronic 100 ë...
Page 39
DHW cylinder, ensure this is refilled in good time. them with special connecting cables. Use only In this connection, observe the manufacturer's instruc- Viessmann cables/lines as replacement. Notify your tions. contractor. In addition for Vitocell 100:...
Appendix Menu overview Vitotronic 300-K Note Depending on the features of your heating system, not all of the checks listed may be available. Where information is marked with , you can call up further details. Boiler sequence Heating Party mode Economy mode Set room temperature Set reduced room temp...
Page 41
Appendix Menu overview Vitotronic 300-K (cont.) Information General Outside temp Boiler sequence Boiler temperature Sensor 17 A Sensor 17 B Common flow temp Output 20 Output 29 Output 52 Feed pump Block 3rd pty dev Central fault mess. Subscriber no. Input ext.
Page 42
Appendix Menu overview Vitotronic 300-K (cont.) Information Heating circuit 2 (HC2), Heating circuit 3 (HC3) Heating program Operating status Time program Set room temperature Room temperature Set reduced room temp Set ext. room temp Set party temp Slope Level Heating circ pump Mixer Flow temperature Return temperature...
Appendix Menu overview Vitotronic 300-K (cont.) Settings Time / Date Language GB Contrast Brightness Temperature unit Name for heating circ. Standard menu Standard setting Terminology Operating program Therefore, heating to the reduced room temperature at night or activating "Economy mode" during short The operating program determines whether you heat absences does not result in significant energy savings.
Page 44
Appendix Terminology (cont.) Heating curve Note If your heating system includes heating circuits with Heating curves illustrate the relationship between the mixers, then the flow temperature for the heating cir- outside temperature, room temperature (set value) and cuit without mixer is higher by a selected differential boiler water or (heating circuit) flow temperature.
Page 45
Appendix Terminology (cont.) Factory settings: Slope = 1.4 and level = 0. Outside temperature in °C Fig. 16 Changing the slope: The gradient of the heating curves changes. Changing the level: The heating curves are shifted in parallel in a verti- cal direction.
Page 46
Appendix Terminology (cont.) Solar circuit pump In conjunction with solar thermal systems. The solar circuit pump transports the heated heat transfer medium from the collectors into the indirect coil of the DHW cylinder. Set temperature Specified temperature that should be reached, e.g. set DHW temperature.
Page 47
DHW temperature............23 Appliance, switching on..........34 DHW temperature, setting..........22 Display backlighting........... 26 Display elements Boiler heating characteristics, changing.....18 – Vitotronic 100, type GC7B........33 Boiler sequence, setting..........26 – Vitotronic 100, type HC1B........33 Brightness, setting............26 – Vitotronic 300-K............33 Burner starts, resetting..........30 Drinking water filter............ 46 Central control............38...
Page 48
Product information............9 – Party mode..............19 Programs, setting – Standby mode........... 19, 34 – For central heating..........17 – Summer mode............19 Symbols............... 8 Symbols on display, Vitotronic 100......12 Reduced room temperature........16 Reduced room temperature (night temperature)..9 Reset................27 Resetting burner starts..........29...
Page 52
Your contact Contact your local contractor if you have any questions about your system or wish to arrange maintenance or repair work. You can find local contractors on the internet at www.viessmann.de. Viessmann Werke GmbH & Co. KG Viessmann Limited...