1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. Catalyst 5000 Series
  6. Installation and configuration note

Cisco Catalyst 5000 Series Installation And Configuration Note

Supervisor engine iii g
Hide thumbs Also See for Catalyst 5000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual, Installation and Configuration Note
Text Part Number:
78-6525-01 Rev. A0
Catalyst 5000 Series
Supervisor Engine III G Installation and
Configuration Note
Product Numbers:
WS-X5550(=) Supervisor Engine III G without Uplink Module
This configuration note contains procedures for installing and verifying the operation of the
Catalyst 5000 series Supervisor Engine III G.
Contents
This document contains the following sections:
•
•
•
•
•
•
•
•
•
•
•
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco Catalyst 5000 Series

Summary of Contents for Cisco Catalyst 5000 Series

  • Page 1: Table Of Contents

    Configuration Note Product Numbers: WS-X5550(=) Supervisor Engine III G without Uplink Module This configuration note contains procedures for installing and verifying the operation of the Catalyst 5000 series Supervisor Engine III G. Contents This document contains the following sections: •...

  • Page 2: Supervisor Engine Iii G Overview

    LED Descriptions State Description SYSTEM Indicates the status of the switch based on a series of self-tests and STATUS diagnostic tests. Green All the tests pass. Any test fails. 2 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 3 Orange The supervisor engine module is in standby mode. 100 Mbps Green The port is operating at 100 Mbps. 1000 Mbps Green The port is operating at 1000 Mbps. Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 4 (DTE) connections with hardware flow control and RJ-45 connectors. A console port accessory kit with the necessary cabling and adapters is provided for making your terminal connection. 4 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 5 The console port mode switch allows you to connect a terminal to the supervisor engine using the desired console cable. The cable and adapters shipped with the switch are the same ones used on the Cisco 2500 Note series routers (and other Cisco products).

  • Page 6: Safety Recommendations

    • Disconnect all power and external cables before installing or removing a chassis. • Do not work alone when potentially hazardous conditions exist. 6 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...

  • Page 7: Removing And Replacing The Supervisor Engine

    (See Figure 3.) If you fail to use the ejector levers to insert the supervisor engine, you can disrupt the order in which the pins make contact with the backplane. When removing a supervisor Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 8 Keep the module at a 90-degree orientation to the backplane. Place the removed supervisor engine on an antistatic mat, foam, or bag. Step 7 8 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 9 The messages are for information only. Enter the show system and show module commands to view specific information. For additional information, refer to the Catalyst 5000 Series Software Configuration Guide and the Catalyst 5000 Series Command Reference publication.

  • Page 10: Connecting A Terminal To The Console Port

    Keeping one hand under the carrier to guide the supervisor engine, carefully slide it into Step 5 the slot on the Catalyst 5000 series switch until the ejector levers click into place on the chassis. Be sure to keep the module horizontal to the backplane and avoid touching any of the components on the module.
  • Page 11 The baud rate of the terminal must match the default baud rate (9600 baud) of the console port. Set up the terminal as follows: • 9600 baud • 8 data bits • No parity • 1 stop bit Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...

  • Page 12: Connecting To The Interface Ports

    GBICs. A GBIC, shown in Figure 6, is a hot-swappable input/output device that plugs into the module, linking the module with the fiber-optic network. GBIC types are listed in Table 4. 12 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...
  • Page 13 GBIC and the MMF cable on both the transmit and receive ends of the link. The patch cord is required for link distances greater than 984 feet (300 m). Refer to the Catalyst 5000 Series Supervisor Engine Installation Guide for more information on patch cords.

  • Page 14: Verifying System Operation

    Catalyst 5505, Catalyst 5509, and Catalyst 5500—If you have a redundant Note supervisor engine, refer to the Catalyst 5000 Series Installation Guide for a detailed description of supervisor engine operation in a redundant configuration. By default, the supervisor engine in slot 1 is the active supervisor; the second supervisor in slot 2 is the standby supervisor.

  • Page 15: Fcc Class A Compliance

    You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 16: Cisco Connection Online

    • Catalyst 5000 Series Route Switch Feature Card Installation and Configuration Note Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly.

  • Page 17: Documentation Cd-Rom

    TransPath, ViewRunner, VirtualStream, VisionWay, VlanDirector, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and Asist, BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, the Cisco Systems Cisco Press logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc.
  • Page 18 Documentation CD-ROM 18 Catalyst 5000 Series Supervisor Engine III G Installation and Configuration Note...

Table of Contents