Warranty; Troubleshooting - STEINEL XLED home 2 SL Information

GB
1� About this document
Please read carefully and keep in a safe place�
– Under copyright. Reproduction either in whole or
in part only with our consent.
– Subject to change in the interest of technical
progress.
Symbols
!
Hazard warning!
Reference to other information in the
document�
...
2� General safety precautions
Disconnect the power supply before
!
attempting any work on the unit�
• Installing these units involves work on the mains
voltage supply; installation must therefore be
carried out professionally in accordance with
the applicable national wiring regulations and
electrical operating conditions (DE-VDE 0100,
AT-ÖVE/ÖNORM E 8001-1, CH-SEV 1000)
• The light must be positioned so that it is not
expected that anybody can stare into the light
for any prolonged period from a distance of less
than 0.3 m.
• The floodlight enclosure heats up when the light
is on. Only adjust the angle of the LED panel
once it has cooled down. Do not look into the
LED light at short range or for any prolonged
period (> 5 min). You could damage your retina.
• Do not install the light on normally flammable
surfaces.
3. XLED home 2 SL /
XLED home 2 XL SL
Proper use
– LED floodlight suitable for wall mounting
outdoors.
– Fully swivelling LED panel.
– Available as standalone floodlight or intercon-
nected with the master version.
With the fully swivelling panel, the floodlight can
be used at home to provide perfect illumination for
lighting up property, or commercially for lighting
up business premises. In conjunction with the opal
cover, this extremely efficient technology provides
wide-area lighting.
Models
– XLED home 2 SL
– XLED home 2 XL SL
Package contents (Fig� 3�1)
Floodlight adjustment range (Fig� 3�2 / 3�3)
Product dimensions (Fig� 3�4 / 3�5)
Product components (Fig� 3�6)
A LED panel
B Enclosure
C Wall mount
4� Electrical installation
Connecting the mains power supply lead
The supply lead consist of three wires:
L = phase conductor (usually black,
brown or grey)
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors
using a voltage tester; then disconnect from the
power supply again. Connect the phase conductor
(L) and neutral conductor (N) to the terminal block.
The protective-earth conductor can be looped
through by means of terminal (E).
Important: Incorrectly wired connections will
produce a short circuit later on in the product or
your fuse box. In this case, you must identify the
individual conductors once again and reconnect
them. The light source of this luminaire cannot be
replaced. If the light source needs to be replaced
(e.g. at the end of its service life), the complete
luminaire must be replaced.
5� Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• Aiming the floodlight. (Fig. 5�1)
Mounting procedure
• Switch OFF power supply. (Fig� 3�7)
• Undo retaining screws. (Fig� 5�2)
• Detach enclosure (B) from wall mount (C).
(Fig� 5�3)
• Detach plug-in terminal (male) from wall mount.
(Fig� 5�4)
– 8 –
• Mark drill holes. (Fig� 5�5)
• Drill holes and insert wall plugs (Fig. 5�6)
• Fit sealing plug. (Fig� 5�7)
– Power supply lead, concealed (Fig� 5�8)
– Power supply lead, surface-mounted, with
spacers (Fig� 5�9)
• Connect conductors. (Fig� 5�10)
• Connect plug-in terminal. (Fig� 5�11)
• Fit enclosure onto wall mount. (Fig� 5�12)
• Screw in retaining screws. (Fig� 5�13)
• Switch ON power supply. (Fig� 5�13)
6� Warranty
This STEINEL product has been manufactured with
utmost care, tested for proper operation and safety
and then subjected to random sample inspection.
Steinel guarantees that it is in perfect condition
and proper working order. The warranty period is
5 years and starts on the date of sale to the con-
sumer. We will remedy defects caused by material
flaws or manufacturing faults. The warranty will be
met by repair or replacement of defective parts at
our own discretion. The warranty shall not cover
damage to wear parts, damage or defects caused
by improper treatment or maintenance.
7� Technical specifications
XLED Home 2 SL
Dimensions (H × W × D) 181 × 180 × 161
Output 14.8 W
Luminous flux / brightness 1184 lm
Weight 0.480 kg
Area illuminated Front view
Side view
Mains current 75 mA
Power factor 0.84
Efficiency 80 lm/W
Colour temperature 4000 K (neutral white)
Colour rendering index Ra ≥ 80
Supply voltage 230-240 ~V / 50/60 Hz
IP / protection class IP44 / II
8� Troubleshooting
Malfunction Cause
Sensor-switched LED floodlight
n Fuse faulty, not switched ON,
without power break in wiring
n Short circuit
Further consequential damage to other objects
shall be excluded. Claims under the warranty will
only be accepted if the unit is sent fully assembled
and well-packed with a brief description of the fault,
a receipt or invoice (date of purchase and dealer's
stamp) to the appropriate Service Centre.
Service: Our Customer Service Department will
repair faults not covered by warranty or after the
warranty period has expired. Please send the prod-
uct well-packed to your nearest Service Centre.
XLED Home 2 XL SL
199 × 180 × 161
20 W
1608 lm
0.525 kg
274.1 cm 2 Front view 307.2 cm
86.3 cm Side view 90.3 cm
2
97 mA
0.86
Remedy
n Replace fuse, turn ON mains
switch, check lead with
voltage tester
n Check connections
– 9 –
2
2