Leviton LT111 Instructions

Cat. No. LT112, LT113 - Advanced - 1000W Tungsten, 15A Resistive/Inductive, 5A Fluorescent, 1/2 HP - 120V, 60Hz

WARNINGS AND CAUTIONS:

• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• Unplug unit when servicing connected devices.
• These timers are for indoor use only.
• Not for use with devices that can overheat if inaccurately timed. Death, injury or property damage could result from such improper use.
• Plug timer into receptacle only.
Introduction
• The illustration ICON DEFINITIONS shows all of the icons found on Cat. Nos.
LT112 and LT113. Cat. Nos. LT111 & LT114 (and LT112 and LT113 when used in
STD mode) only show the icons for the standard functionality.
• Only Cat. No. LT112 & LT113 have the Random Mode, Daylight Savings Time
Option and Automatic Sunup/Sundown control.
• Timer Schedule at a Glance will allow you to quickly see your timers ON/OFF
settings for the day. The displayed segments represent the time(s) your load will
be on. The segment representing the current time will be flashing.
Battery
• The battery compartment is located in the back of the Timer. To replace the
battery, remove the battery from the back of the device by pressing the top of the
battery clip down and sliding out the battery housing. When replacing the battery,
ensure that the polarity of the battery is correct (the + side of the battery should
be facing the + side of the battery holder). When the battery housing door is flush
with the back housing, slide the lock up until you hear an audible click. This door
lock prevents the battery from dislodging in the event the device is dropped.
• Use CR2016 Lithium Ion battery for replacement. DO NOT replace with any other
battery type.
• To save battery life when storing the timer for an extended period of time, rotate
the battery so the + side of the battery is opposite the + side of the battery
holder. Programmed events will be retained.
• The battery icon will be lit when the timer is operating on battery power. It will
blink when the battery needs replacement.

Before Programming your Device

NOTE: The timer programming can be performed holding the timer in your hand, while operating on
battery power.
Remove the battery door and remove the plastic shield from the battery. Slide the battery
housing back into the device.
Perform a SYSTEM RESET by pressing and holding
and begins to flash (approximately 5 seconds). Press
NOTE: For Cat. Nos. LT112 & LT113, once the self test is complete
to choose which mode is best for your application:
Pro mode or Standard mode
Programming Mode section for your device.
Pro Mode provides up to 50 ON/OFF events for any day or combination of days, M-Su, M-F,
or Sa-Su at desired fixed times or self adjusting Sunup and Sundown times. In this mode self
adjusting Daylight Savings Time and random modes are also available.
Std Mode provides up to 3 ON/OFF events for M-Su, M-F, or Sa-Su at desired fixed times only.
Self adjusting Sunup and Sundown and Daylight Savings Time are NOT available in Standard Mode.
To exit programming at any time press the OVERRIDE button -
For Cat. Nos. LT111 & LT114, once the self test is complete
programming there are two ways to scroll through the choices; you can either continuously press an arrow button or press and hold an arrow button to progress rapidly.

Programming Standard Mode

To set the clock:
• will be flashing. Use
A
• will be flashing. Use
A
A AM P PM
• for or for will be flashing. Use
• The day of the week will be flashing. Use
To set ON/OFF Events:
until PRG is in the lower left corner. Press
• Press MENU
• Event 1 will be flashing. Press
• All days of the week will be flashing. Press
week choice and continue to program the event ON TIME.
• At use or to choose
• Use or to choose the hour and press
• At 6:00P press to choose the OFF TIME or use
SET
• Continue to set desired events in the same manner. When you are done press
the device will automatically exit out of programming mode.

Programming Pro Mode

Setting up the Time, Daylight Savings Time Option and the Date:
• will be flashing. Press
A
• will be flashing. Press
A
A P
• or will be flashing. Press
• will be flashing. Set the daylight savings time mode to OFF or AUTO (for auto adjustment of daylight savings time) by using
option. Press to confirm your choice. NOTE: Daylight Savings Time shall start at 2am on the 2nd Sunday of March (add 1 hour) and end at 2am on the 1st Sunday of November
SET
(subtract 1 hour).
• will be flashing. Use
• will be flashing. Use
•
will be flashing. Use
The day of week will automatically adjust.
Cat. No. LT111 - Standard - 500W Tungsten, 10A Resistive / 5A Inductive, 1/3 HP - 120V, 60Hz
Cat. No. LT114 - Table Top - 300W Tungsten, 8.3A Resistive/Inductive, 1/3 HP - 120V, 60Hz
SET
followed by
to confirm SYSTEM RESET.
SET
Press
will be flashing. Continue on to the Programming Standard Mode section for your device. NOTE: While
A
- Cat. Nos. LT111, LT114 (and LT112, LT113 in
or to choose the hours. Press
or to choose the minutes. Press
or to choose the
or to choose the day. Press
SET to enter the programming mode.
SET to choose this event or use
SET
to choose all days of the week or use
for time, or to delete an existing program and press
to confirm your choice. Do the same for minutes and press
SET
or
- Cat. Nos. LT112, LT113
or to select the hour and press
or to select the minutes and press
A AM P
or to select for or
or to choose the year and press
or to choose the month and press
or to choose the date and press
Indoor Plug-In Timer
INSTRUCTIONS
Permanent override OFF (schedule at a glance not available)
Temporary override OFF (when flashing)
Permanent override ON (schedule at a glance not available)
Temporary override ON (when flashing)
Timer Mode
Programming
Menus
Timer schedule
OVERRIDE
until stops flashing
will be flashing. Use or
SET
and continue on to the
OVERRIDE
SET
to confirm your choice.
to confirm your choice.
SET
A P
or . Press to confirm your choice.
SET
to confirm your choice.
SET
to move to the next event and press
to scroll through M-F and Sa-Su. Press
or
to choose to delete an existing program and press
to escape out of programming. If no buttons are pressed after approximately 30 seconds
OVERRIDE
SET to confirm your choice.
to confirm your choice.
SET
PM
for and press SET to confirm your choice.
to confirm your choice.
SET
to confirm your choice
SET
to confirm your choice.
SET
ICON DEFINITIONS
Event number Daylight
Savings Time
DST
Event
6
AM
MTWThFSaSu
Offset
Offset of
at a glance astronomic clock
Display
Menu
Button
Override
Button
mode)
SET
to confirm your event number choice.
to confirm your choice.
SET
to confirm your choice. Continue to program the event OFF TIME.
SET
to confirm your choice.
SET
PK-93694-10-00-2A
English
Sun down
Day time
Sun up
Delete
Setting Timed
Events
Longitude/
Latitude
degrees
A
AM or PM
P
6
PM
Battery power
(No AC power)
Days of Night time
the week
Set
Button
MENU SET
Arrow
Buttons
OVERRIDE
SET to confirm your days of the
or to choose daylight savings time