All the information in this guide is based upon the latest product information available at the time of publication. At Kohler Company, we strive to fulfill our mission of improving the level of gracious living for each person who is touched by our products and services.
For the spray head must be descaled regularly. ¨ NOTE: When removing the unit from package, a small amount of water may be found inside. This is normal as the unit is tested during manufacturing process. Kohler Co. 1237889-X2-G...
Simplified Diagram K-5627X ELCB TEST RESET Front Plate Adjustable Shower Holder Power Indicator Slider Rail ELCB Indicator Flexible Hose Temperature Control Knob Soap Tray Stop Valve Mesh Filter Rail Support ELCB Test and Reset Button Handshower Flow Regulator 1237889-X2-G Kohler Co.
Page 5
K-72989X ELCB TEST RESET Front Plate Power Indicator ELCB Indicator Temperature Control Knob Stop Valve Mesh Filter ELCB Test and Reset Button Flexible Hose Handshower Flow Regulator Bracket Kohler Co. 1237889-X2-G...
Prior to installation, unpack the new product and inspect it for damage. ¨ The walls and the floor must be square, plumb, and level. ¨ Fixture dimensions are nominal and conform to tolerances established by ¨ Standards TIS. 1237889-X2-G Kohler Co.
Thermostat (double-action) Flow Switch Main Control ELCB TEST & RESET switch Display ELCB Preparation Be sure to install the unit on the wall. ¨ The unit must be installed at 1.5-1.7 m above the floor. ¨ 1.5-1.7 m Kohler Co. 1237889-X2-G...
Page 8
Roughing-In Dimensions are approximate. Unit: mm K-5627X Finished Wall Mounting Hole Mounting Mounting Hole Hole 1500-1700 Ø 1200-1400 Finished Floor NOTE: The recommended dimension for installation can be adjusted according to user preferences and layout. 1237889-X2-G Kohler Co.
Page 9
Roughing-In (cont.) K-72989X Finished Wall 400-600 Mounting Hole Mounting Hole Mounting Hole Mounting Hole 1500-1800 1500-1700 Finished Floor NOTE: The recommended dimension for installation can be adjusted according to user preferences and layout. Kohler Co. 1237889-X2-G...
Insert the shower holder and ¨ soap tray into the slider rail. Mount the slider rail to the rail bracket. ¨ Remove the cap from the rail bracket and screw the bracket to marked ¨ position. Replace the cap. 1237889-X2-G Kohler Co.
WARNING: Risk of property or product damage. The water inlet and outlet must be installed correctly, otherwise heater unit will not function. WARNING: Risk of property or product damage. Do not apply plumping cement on connection. Whenever necessary, use only thread or sealing tape. Kohler Co. 1237889-X2-G...
Cut a small groove on the rubber seal “A“ (at the back of heater base) with ¨ a cutter for cable inserting. 1237889-X2-G Kohler Co.
Page 13
VR shaft. (at the front cover). Press the upper part of the front of cover until it locks. Ensure the temperature ¨ control knob fix properly and screw the front cover to the heater base. This Position This Position Kohler Co. 1237889-X2-G...
Page 14
Press the “RESET” button, the heater unit should resume normal function, ¨ the green indicator should light on. If procedures stated above prevailed, the ELCB is functioning in normal condition. Switch off the electricity supply. ¨ 1237889-X2-G Kohler Co.
(72989X). NOTICE: It is unnecessary to turn the temperature control knob to “OFF” position when the heater is not in use. Switch off the electricity supply after shower. ¨ Handshower Sprays Kohler Co. 1237889-X2-G...
Never try to repair the unit by yourself. CAUTION: Risk of product damage. Do not use thinner, alcohol, petrol or any other organic solutions to clean the unit. Use only damped cloth with mild detergent. 1237889-X2-G Kohler Co.
C. Temperature control C. Turn the temperature knob is set too high. control knob counter- clockwise until a cooler temperature is achieved. D. The thermostat is faulty D. Replace. or damaged. Kohler Co. 1237889-X2-G...