Advertisement
Quick Links
COOLING ONLY MODELS
OPERATING LIMITS
í Maximum conditions
Outdoor temperature : 52¡C D.B.*
Room temperature
: 35¡C D.B. / 22.5¡C W.B.
í Minimum conditions
Outdoor temperature : 19¡C D.B.**
Room temperature
: 19¡C D.B. / 14¡C W.B.
í Model name GRxxxL - GRVxxxL
*: 50¡C D.B. **: Ð15¡C D.B.
HEAT PUMP MODELS
OPERATING LIMITS
í Cooling Maximum conditions
Outdoor temperature : 46¡C D.B.
Room temperature
: 35¡C D.B. / 22¡C W.B.
í Cooling Minimum conditions
Outdoor temperature : 19¡C D.B.
Room temperature
: 19¡C D.B. / 14¡C W.B.
í Heating Maximum conditions
Outdoor temperature : 24¡C D.B. / 18¡C W.B.
Room temperature
: 27¡C D.B.
í Heating Minimum conditions
Outdoor temperature : Ð8¡C D.B. / Ð9¡C W.B.
COOLING ONLY MODEL KPAV128C5
OPERATING LIMITS
í Maximum conditions
Outdoor temperature : 43¡C D.B.
í Minimum conditions
Outdoor temperature : 19¡C D.B.*
í Model name GRxxxL-GRVxxxL
*Ð15¡C D.B.
HEAT PUMP MODEL KPA128R5-KPAV128R5
OPERATING LIMITS
í Cooling Maximum conditions
Outdoor temperature : 43¡C D.B.
Room temperature
: 32¡C D.B. / 23¡C W.B.
í Cooling Minimum conditions
Outdoor temperature : 19¡C D.B.
Room temperature
: 19¡C D.B. / 14¡C W.B.
í Heating Maximum conditions
Outdoor temperature : 24¡C D.B. / 18¡C W.B.
Room temperature
: 27¡C D.B.
í Heating Minimum conditions
Outdoor temperature : Ð8¡C D.B. / Ð9¡C W.B.
Tools required for installation (not supplied)
1. Standard screwdriver
2. Phillips head screwdriver
3. Knife or wire stripper
4. Tape measure
5. Level
6. Sabre saw or key hole saw
7. Hacksaw
8. Core bits ¿ 5
01/2000
Room temperature : 32¡C D.B. / 23¡C W.B.
Room temperature : 19¡C D.B. / 14¡C W.B.
9. Hammer
10. Drill
11. Tube cutter
12. Tube flaring tool
13. Torque wrench
14. Adjustable wrench
15. Reamer (for reburring)
INSTALLATION INSTRUCTIONS
-
Floor or celling mounted split units
DECLARATION OF CONFORMITY
This product is marked
Ð Low voltage no. 73/23 EEC and 93/68 EEC.
Ð Electromagnetic compatibility no. 89/336 ECC, 92/31 EEC
and 93/68 EEC.
This declaration will become void in case of misuse and/or non
observance though partial of manufacturer's installation and/or
operating instructions.
Model Combinations
Combine indoor and outdoor units only as listed below.
COOLING ONLY MODELS R22
Indoor Units
KPAV128C5
KPAV185C5
KPAV225C5
HEAT PUMP MODELS R22
Indoor Units
KPA128R5
KPAV184R5
KPAV224R5
COOLING ONLY MODELS R407C
Indoor Units
KPAV128C5
KPAV185C5
KPAV225C5
HEAT PUMP MODELS R407C
Indoor Units
KPAV128R5
KPAV184R5
KPAV224R5
Power Supply:
The last digit(s) of the model number indicates the required
power supply to the unit.
5: 220 - 240 V ~ 50 Hz / 7: 380-400 V - 3N ~ 50 Hz
Last digit(s) of the model number
SKP-C/SKP-R
as it satisfies Directives:
Outdoor Units
GR129C5
GR127L5
GR185C5
GR185C7
GR226C5
GR226C7
Outdoor Units
GR129R5
GR184R5
GR224R5
Outdoor Units
GRV127L5
GRV185C5
GRV185C7
GRV185L5
GRV185L7
GRV226C5
GRV226C7
Outdoor Units
GRV127R5
GRV184R5
GRV224R5
10 11 306 F.GB.I.E.D.03
-
EG
I
F
D
E
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Technibel Climatisation GR12 Series
Summary of Contents for Technibel Climatisation GR12 Series
- Page 1 INSTALLATION INSTRUCTIONS Floor or celling mounted split units SKP-C/SKP-R COOLING ONLY MODELS DECLARATION OF CONFORMITY OPERATING LIMITS í Maximum conditions This product is marked as it satisfies Directives: Outdoor temperature : 52¡C D.B.* Ð Low voltage no. 73/23 EEC and 93/68 EEC. Room temperature : 35¡C D.B.
- Page 2 IMPORTANT! • Ground the unit following local electrical codes. • The Yellow/Green wire cannot be used for any connection Please read before installation different from the ground connection. • Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard. This conditioning system meets strict safety and operating •...
-
Page 3: Electrical Data
Installation site selection - Indoor unit • Select a sufficiently strong location to support the weight of the AVOID unit. • Direct sunlight. • Select a location where tubing and drain hose have the shortest • Nearby heat sources that may affect unit performance. run to the outside. -
Page 4: Istruzioni Di Installazione
ISTRUZIONI DI INSTALLAZIONE Condizionatore d’aria Split System a pavimento o soffitto SKP-C/SKP-R MODELLI SOLO FREDDO DICHIARAZIONE DI CONFORMITÀ LIMITI DI FUNZIONAMENTO Questo prodotto è marcato in quanto conforme alle í Condizioni Massime Direttive: Temperatura esterna : 52°C B.S.* – Bassa Tensione n. 73/23 CEE e 93/68 CEE. Temperature interne : 35°C B.S. - Page 5 IMPORTANTE! ¥ Eseguire la messa a terra dellÕunitˆ secondo le norme elettriche locali. Leggere prima di iniziare lÕinstallazione ¥ Il conduttore giallo/verde non pu˜ essere utilizzato per collegamenti diversi dalla messa a terra. Questo sistema di condizionamento deve seguire rigidi standard ¥...
-
Page 6: Dati Elettrici
Scelta del luogo di installazione unitˆ interna ¥ Verificare che il piano di appoggio sia sufficientemente resistente da EVITARE sostenere il peso dellÕunitˆ. ¥ LÕesposizione diretta al sole. ¥ Scegliere una posizione in modo che la distanza tra le due unitˆ sia ¥... -
Page 7: Notice D'installation
NOTICE D’INSTALLATION Split consoles et plafonniers SKP-C/SKP-R MODELES FROID SEUL DECLARATION DE CONFORMITE LIMITES DE FONCTIONNEMENT Ce produit est marqué puisque il est conforme aux í Conditions maximales Directives: Température extérieure : 52°C B.S.* – Basse Tension n. 73/23 CEE et 93/68 CEE. Température intérieure : 35°C B.S. - Page 8 IMPORTANT! • Effectuez la mise ˆ la terre de l'appareil en respectant les réglementations électriques locales. Veuillez lire ce qui suit avant de commencer • Le câble jaune/vert ne peut en aucun cas être utilisé pour toute autre connexion que celle de la mise à la terre. •...
- Page 9 Choix de l'emplacement d'installation - Appareil intŽrieur RECHERCHEZ • Un emplacement approprié à partir duquel l'ensemble de la pièce peut être EVITEZ climatisé de manière uniforme. • L'exposition directe au soleil. • Un emplacement suffisamment solide pour supporter le poids de l'appareil. •...
- Page 10 INSTALLATIONSANLEITUNGEN Split-Konsolen und deckengerŠte SKP-C/SKP-R NUR K†HLUNG MODELLE KONFORMIT€TSERKL€RUNG BETRIEBSBEREICH í Maximumbedingungen Dieses Produkt ist mit -Zeichen gekennzeichnet, weil Au§entemperatur : 52¡C T.K.* es den folgenden Richtlinien entspricht: Raumtemperatur : 35¡C T.K. / 22.5¡C F.K. Ð Niederspannungsrichtilinie 73/23 EWG und 93/68 EWG. í...
- Page 11 WICHTIG! ¥ Erden Sie das GerŠt gemŠ§ den šrtlich zutreffenden Bitte vor Arbeitsbeginn lesen Vorschriften. ¥ Das Gelbe/GrŸne Kabel ist fŸr die ausschlie§liche Verwendung als Erdleitung. Diese Klimaanlage entspricht strengen Sicherheits- und ¥ Verbinden Sie Kabel fest miteinander. Lockere Verbindungen Betriebsnormen.
-
Page 12: Elektrische Angaben
Wahl des Installationsortes - InnenraumgerŠt ¥ WŠhlen Sie eine Stelle, an der der Boden das Gewicht des GerŠtes tragen VERMEIDEN SIE kann. ¥ Direkte Sonneneinstrahlung. ¥ WŠhlen Sie eine Stelle, von der aus die Rohre und der ¥ WŠrmequellen in der NŠhe des GerŠtes, die dessen LeistungsfŠhigkeit Wasserablaufschlauch den kŸrzesten Weg nach daru§en haben. -
Page 13: Instrucciones De Instalacion
INSTRUCCIONES DE INSTALACION Consolas split suelo y techo SKP-C / SKP-R MODELOS SOLO REFRIGERACION DECLARACION DE CONFORMIDAD LIMITES DE FUNCIONAMIENTO í Condiciones Máximas Este Producto está marcado porque responde a las Directivas: Temperatura exterior : 52°C B.S.* – Baja Tensión n° 73/23 CEE y 93/68 CEE. Temperatura interior : 35°C B.S. - Page 14 !IMPORTANTE! • Realizar la puesta a tierra de la unidad siguiendo las normas eléctricas locales. Leer antes de empezar la instalaci—n • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. • Fijar bien los cables. Un error en las uniones puede provocar Este sistema de acondicionamiento cumple medidas rígidas de recalentamiento o un posible incendio.
-
Page 15: Datos Electricos
D—nde instalar la unidad interior • Controlar que el lugar de apoyo es lo suficientemente resistente como EVITAR para soportar el peso de la unidad. • La exposición directa al sol. • Elegir una posición de modo que la distancia entre las dos unidades •... - Page 16 ACCESSORY FOR UNDER - CEILING OR WALL INSTALLATION PARTS FIGURE Q.TY PARTS FIGURE Q.TY BRACKET BOLT M8 WASHER - SPRING WASHER SPECIAL WASHER ACCESSORIES SUPPLIED WITH THE UNIT PARTS FIGURE Q.TY PARTS FIGURE Q.TY PARTS FIGURE Q.TY REMOTE CONTROL RAWL PLUG BRACKET UNIT SCREW PLASTIC...
- Page 17 MITGELIEFERTES ZUBEH…R F†R INSTALLATION AN EINER WAND ODER DECKE TEILE ABBILDUNG MENGE TEILE ABBILDUNG MENGE TRAGB†GEL SCHRAUBENBOLZ SCHEIBE- FEDERSCHEIBE BESONDERE SCHEIBE MITGELIEFERTES ZUBEH…R TEILE ABBILDUNG MENGE TEILE ABBILDUNG MENGE TEILE ABBILDUNG MENGE SCHRAUBE F†R D†BEL B†GEL FERNBEDIENUNG PLASTIKAB- AAA ALKALINE SEITENWAND DECKUNG BATTERIE...
- Page 18 INDOOR UNIT ¥ UNITç INTERNA ¥ UNITE INTERIEURE ¥ INNENEINHEIT ¥ UNIDAD INTERIOR Minimum operation and maintenance area. 3000 Area minima di esercizio e manutenzione. Surface minimum de fonctionnement et d’entretien. Raumbedarf des GerŠtes. Area mínima de funcionamiento y manutención. 3000 max 400 Find the place for the installation.
- Page 19 Wall installation. Place the fullscall diagram, level it and mark the holes to drill (pipes and rawl plugs). Installation murale. Placer le gabart de perçage, le mettre deriveau et marquer les trous à faire (chevilles). Installation murale. Placer le gabarit de perçage, le mettre de niveau et marquer les trous à faire (tuyaux et chevilles).
- Page 20 Drill a hole (see table), insert a PVC pipe, fit the plastic cover supplied with the unit. Eseguire un foro (vedi tabella). Inserire ed adattare un tubo in plastica. Fissare il tappo in dotazione. 5 - 10 mm Faire un trou (voir table). Introduire et adapter un tube PVC. Fixer l’enjoliveur fournit.
- Page 21 Predispose the fixing of the bracket. Running power electric cable (with a ground wire) between the two units (see the table of wire section). Check if the quantity and the rawl plugs type supplied are the proper ones for fixing the unit on the wall. Predisporre il fissaggio della zanca a muro.
- Page 22 KIT FOR UNDER-CEILING OR WALL INSTALLATION Fix the brackets on the back side of the unit using the bolts supplied in the kit. Use rawl plugs suitable to the wall consistence and four threaded bars of suitable length. (not supplied). KIT PER INSTALLAZIONE A PARETE OPPURE A SOFFITTO Fissare le staffe sul retro dell'unitˆ...
- Page 23 Under ceiling installation Predispose the condensate drain pipe with a positive slope to the outside. Cut the angle of the return air grille as marked on the internal side. Installazione a soffitto Predisporre il tubo scarico condensa rispettando la pendenza. Tagliare l'angolo 5 - 10 mm della griglia di aspirazione come evidenziato.
- Page 24 Préparer les câbles électriques pour le branchement dans la boîte à bornes et les connecteur. (Voir schéma pour le branchement). Serrer les câbles d'alimentation a la bague de serrage de la bride. DANGER S'assurer que les bornes des c‰bles Žlectriques soient bien serrŽes sur la bo”te ˆ...
- Page 25 Install the condensate to drain the outside with a positive slope. Convogliare la condensa verso l'esterno assicurando una buona pendenza. Diriger les condensats vers l'extérieur, en assurant une bonne pente. Das Kondenswasser-Rohr nach drau§en mu§ mit einer guten Neigung nach unten verlegt werden.
- Page 26 OUTDOOR UNIT ¥ UNITç ESTERNA ¥ UNITE EXTERIEUR ¥ AU§ENEINHEIT ¥ UNIDAD EXTERIOR Minimum operation and maintenance area Area minima di esercizio e manutenzione. Surface minimum de fonctionnement et d’entretien. Raumbedarf des GerŠtes. Area mínima de funcionamiento y manutención. Provide a solid base for outdoor unit raised from the ground level. Fix unit to base using 4 anchor bolts.
- Page 27 Heat pump version. Use, if necessary, the accessories supplied. Versione pompa di calore. Utilizzare, se necessario, il materiale a corredo. Version reversible. Si nécessaire, employer les accessoires livrés. WŠrmepumpe-AusfŸhrung. Wenn nštig, das mitgelieferte Material benutzen. Modelos con bomba de calor. Utilizar, si fuera necesario, los accesorios suministrados.
- Page 28 Insert flare nuts removed from the units, then make a flare at the end of copper tubes. Cartellare le estremitˆ dei tubi ricordandosi di infilare i bocchettoni rimossi dalle unitˆ. Evaser les extrémités des tubes, aprés avoir placé les écrous récupérés sur les unités.
- Page 29 Insulate tubes leaving connections uncovered for leak test. Isolare accuratamente i tubi lasciando libere le giunzioni per la prova di tenuta. Isoler soigneusement les tubes en laissant libres les jonctions pour l'essai d'etanchéité. Die Ršhre gut isolieren; die Verbindungen aber fŸr die Dichtheits-PrŸfung frei lassen.
- Page 30 With vacuum pump still running close the low pressure knob on valve manifold. Then stop vacuum pump. Using the hexagonal key suplied as accessory open the service valve on small tube, then close it after 10 seconds. Check tightness of all joints using liquid soap. Con la pompa del vuoto in funzione chiudere il rubinetto del gruppo manometrico (bassa pressione).
- Page 31 BASIC FUNCTIONS OF THE SERVICE VALVES ¥ FUNZIONI PRINCIPALI DELLE VALVOLE ¥ FONCTIONS DE BASE DE VANNE DE SERVICE ¥ FUNKTION DER ABSPERRVENTILE ¥ PRINCIPALES FUNCIONES DE LAS VALVULAS Wide tube service valve (3-way) Narrow tube service Action valve (2-way) GR12X-GRV12X/GR18X-GRV18X GR22X-GRV22X Valve cap...
- Page 32 Complete insulation of refrigerant tubes; wrap with insulation tape. Fix and support tubes with brackets. Seal hole in the wall, if necessary. Completare l'isolamento, proteggere con nastratura, fissare e supportare con staffe; se necessario sigillare il foro di passaggio nel muro. Compléter l'isolation des tubes, les protéger avec des rubans, les fixer avec des brides;...
- Page 33 SYSTEM WIRING DIAGRAM ¥ COLLEGAMENTI ELETTRICI DEL SISTEMA ¥ BRANCHEMENTS ELECTRIQUES DU SYSTEME ¥ ELEKTRISCHE ANSCHL†SSE DES SYSTEMS ¥ CONEXIONES ELECTRICAS DEL SISTEMA COOLING ONLY MODELS GR12X-GRV12X MODELLI SOLO FREDDO MODELES FROID SEUL NUR K†HLUNG MODELLE OUTDOOR UNIT MODELOS SOLO REFRIGERACION INDOOR UNIT POWER SUPPLY...
- Page 34 GR18X-GRV18X GR22X-GRV22X 3-PHASE MODELS 3-PHASE MODELS MODELLI TRIFASE MODELLI TRIFASE MODELES TRIPHASES MODELES TRIPHASES DREIPHASENMODELLE DREIPHASENMODELLE MODELOS TRIFçSICO MODELOS TRIFçSICOS INDOOR UNIT INDOOR UNIT OUTDOOR OUTDOOR UNIT GROUND UNIT POWER SUPPLY GROUND 380-400V - 3N ~ 50Hz POWER SUPPLY 380-400V - 3N ~ 50Hz GR22X-GRV22X 1-PHASE MODELS NOTE: 3-phase models.
- Page 35 TEST RUN ¥ COME ESEGUIRE LA PROVA DEL CONDIZIONATORE (TEST RUN) ¥ CONTROLE FINALE ENDKONTROLLE ¥ COMO REALIZAR LA PRUEBA DEL ACONDICIONADOR (TESTRUN) Operation selector switch TEST Cooling mode Heating mode Switch on the power supply. Press the ON/OFF button and change Switch on the power supply.
- Page 36 REMOTE CONTROL UNIT INSTALLATION ¥ POSIZIONE DI INSTALLAZIONE TELECOMANDO ¥ EMPLACEMENT DE LA COMMANDE A DISTANCE ¥ POSITION DER FERNBEDIENUNG ¥ POSICION DE INSTALACION DEL MANDO A DISTANCIA REMOTE CONTROL UNIT INSTALLATION The remote control unit may operated either from a non-fixed position or from a wall-mounted position. To ensure that the air conditioner operates correctly.
- Page 37 WALL / MURO / MUR WALL / MURO / MUR THE SCREWS NECESSARY FOR THE TWO DIFFERENT WAND / PARED WAND / PARED INSTALLATIONS ARE SUPPLIED WITH THE INDOOR UNIT. LE VITI NECESSARIE ALLE DUE TIPOLOGIE DI INSTALLAZIONE SONO FORNITE A CORREDO DELLÕUNITË INTERNA.
- Page 38 PUMP DOWN Pump down means collecting all refrigerant gas in the system quand on doit déplacer le climatiseur, et pour les interventions de réparation sur le circuit frigorifique. back into the outdoor unit without losing gas. Pump down is used when the unit is to be moved of before servicing the Das bedeutet: das KŸhlmittel in die Au§eneinheit ohne Gas- refrigerant circuit.
- Page 39 ELECTRIC WIRING SYSTEMS - COOLING ONLY MODELS ¥ SCHEMA ELETTRICO DEI SISTEMI - MODELLI SOLO FREDDO ¥ SCHEMA ELECTRIQUE DES UNITES - MODELES FROID SEUL ¥ SYSTEM-SCHALTPLAN - NUR K†LUNG MODELLE ¥ ESQUEMA ELECTRICO DE LOS SISTEMAS - MODELOS SOLO REFRIGERACION KPAV128C5 GR129C5 OLR (A)
- Page 40 KPAV185C5 GR185C7 - GRV185C7 GRN/YEL GRN/YEL GRN/YEL GRN/YEL ROOM COIL L M H FM THERMO GRN/YEL SW ASSY IND ASSY (C) T GRN/YEL KPAV185C5 GRV185L5 GRN/YEL GRN/YEL GRN/YEL RELAY (AIR) (COIL) PCB 1 L M H FM SWITCH ASSY SW ASSY CONTROLLER REC ASSY GRN/YEL...
- Page 41 KPAV225C5 GR226C5 - GRV226C5 GRN/YEL GRN/YEL GRN/YEL ROOM COIL GRN/YEL L M H FM GRN/YEL GRN/YEL GRN/YEL SW ASSY IND ASSY THERMO KPAV225C5 GR226C7 - GRV226C7 GRN/YEL GRN/YEL ROOM COIL L M H FM GRN/YEL SW ASSY IND ASSY...
- Page 42 ELECTRIC WIRING SYSTEMS - HEAT PUMP MODELS ¥ SCHEMA ELETTRICO DEI SISTEMI - MODELLI POMPA DI CALORE ¥ SCHEMA ELECTRIQUE DES UNITES - MODELES REVERSIBLES ¥ SYSTEM-SCHALTPLAN - W€RMEPUMPE MODELLE ¥ ESQUEMA ELECTRICO DE LOS SISTEMAS - MODELOS CON BOMBA DE CALOR KPA128R5 - KPAV128R5 GR129R5 - GRV127R5 KPAV184R5...
- Page 43 Description of symbols / Descrizione dei simboli / Description des symboles / Bezeichnung der Symbole / Descripci—n de los s’mbolos SYMBOL CRANK CASE HEATER RISCALDATORE CARTER RESISTANCE DE CARTER-MOTEUR KURBELGEH€USEHEIZUNG CALENTADOR DEL CÁRTER COMPRESSOR MOTOR MOTORE COMPRESSORE MOTEUR DE COMPRESSEUR KOMPRESSORMOTOR MOTOR DEL COMPRESOR C1, 2, 3...
- Page 44 In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und kšnnen VorankŸndigung abgeŠndert Werden.
Need help?
Do you have a question about the GR12 Series and is the answer not in the manual?
Questions and answers