Texas Instruments SLEU056 User Manual
Texas Instruments SLEU056 User Manual

Texas Instruments SLEU056 User Manual

Evaluation module for the tas5010 digital audio pwm processor and the tas5112adfd digital audio pwm power output stage
Table of Contents

Advertisement

Quick Links

TAS5010−5112F2EVM
Evaluation Module for the TAS5010 Digital
Audio PWM Processor and the TAS5112ADFD
Digital Audio PWM Power Output Stage
User's Guide
June 2004
DAV Digital Audio/Speaker
SLEU056

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SLEU056 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texas Instruments SLEU056

  • Page 1 TAS5010−5112F2EVM Evaluation Module for the TAS5010 Digital Audio PWM Processor and the TAS5112ADFD Digital Audio PWM Power Output Stage User’s Guide June 2004 DAV Digital Audio/Speaker SLEU056...
  • Page 2 TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:...
  • Page 3 Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods.
  • Page 4 EVM schematic located in the EVM User’s Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Copyright © 2004, Texas Instruments Incorporated Mailing Address: Texas Instruments...
  • Page 5 About This Manual This manual describes the operation of the TAS5010−5112F2EVM evaluation module from Texas Instruments. How to Use This Manual This document contains the following chapters: Chapter 1 – Overview Chapter 2 – Detailed Description of the EVM Board Chapter 3 –...
  • Page 6: Related Documentation From Texas Instruments

    Trademarks Equibit™ and PurePath Digital™ are trademarks of Texas Instruments. Literature Number SLAS328 SLES094...
  • Page 7: Table Of Contents

    Introduction ..............TAS5010−5112F2EVM Features Detailed Description of the EVM Board Overview...
  • Page 8 Contents Figures 1−1 Simplified TAS5010−5112F2EVM Block Diagram 2−1 Board Outline With Connectors, Switches, Jumpers, and Indicators 2−2 Physical Structure for the TAS5010−5112F2EVM 2−3 Default Jumper Positions 2−4 Pin Numbers at the Line Input/Output Connector (Top View) 2−5 Pin Numbers at the Parallel Port/I 2−6 Pin Numbers at PSU Connector (Top View) 3−1...
  • Page 9: Introduction

    The TAS5010−5112F2EVM PurePath Digitalt customer evaluation module demonstrates two integrated circuits, the TAS5010 and TAS5112ADFD from Texas Instruments. The TAS5010 is a high performance 24-bit stereo digital modulator based on Equibitt technology. This IC converts input PCM serial digital audio data to a pulse width modulated (PWM) audio data stream. The TAS5010 PWM modulator accepts I S data with a sample rate up to 192 kHz.
  • Page 10: Tas5010−5112F2Evm Features

    DAP control through PC software (DCT software from Texas Instruments) Default DAP settings is downloaded to an EEPROM with the DCT software Analog line input (use internal analog-to-digital converter in DAP) Analog line output (use internal digital-to-analog converter in DAP) Figure 1−1.
  • Page 11 TAS5010−5112F2EVM Features The TAS3002 IC from Texas Instruments is used as digital audio processor (DAP). All features in the DAP can be controlled through the I S interface. Adjustment of the sound level can be executed through the I C bus and with two push buttons on the EVM board.
  • Page 13: Detailed Description Of The Evm

    Detailed Description of the EVM This chapter describes the TAS5010−5112F2EVM board in regards to board layout, jumpers, switches, buttons, and connectors. Topic Board Overview ..........Description of Jumper Settings Default Jumper Positioins .
  • Page 14: Board Overview

    Board Overview 2.1 Board Overview Figure 2−1. Board Outline With Connectors, Switches, Jumpers, and Indicators S/PDIF Digital Audio J100 Coaxial/RCA Input Coaxial Switch between Optical S/PDIF ERROR and Coaxial input ENABLE Optical S/PDIF Digital Audio J101 Optical/Toslink Input A/D−Converter Output J170 D/A−Converter Input J160...
  • Page 15: Description Of Jumper Settings

    2.2 Description of Jumper Settings There are three jumpers on the EVM board (J400 is an I 2.2.1 Double-Speed Control (JMP120) JMP120 is used to set the double-speed pin at TAS5010 (DBSPD, pin 39). The TAS5010 is operating in single-speed mode if the DBSPD pin is asserted low and in double-speed if it is asserted high.
  • Page 16: Default Jumper Positioins

    Default Jumper Positioins 2.3 Default Jumper Positioins Default jumper positions are marked with a grey rectangle in Figure 2−3. Figure 2−3. Default Jumper Positions J100 JMP130 JMP120 J101 J170 J160 JMP360 J300 2.4 Description of Connectors 2.4.1 S/PDIF Digital Audio Coaxial/RCA Input (J100) The RCA connector can be connected to a digital S/PDIF source through a coaxial cable with 75-Ω...
  • Page 17: Pc And I2 C Interface (J300)

    Table 2−1. Description of J160 and J170 Pin No. Analog Input Connector (J160) Analog Output Connector (J170) 2.4.4 PC and I C Interface (J300) The PC interface using the attached special cable to parallel/printer port on the PC. This makes it possible to control the TAS3002 digital audio processor totally from the PC using the special DCT software saved on the PurePath Digitalt amplifier CD-ROM.
  • Page 18: Loudspeaker Connectors (J540, J541, J580, And J581)

    Description of Connectors 2.4.5 Loudspeaker Connectors (J540, J541, J580, and J581) All speaker connectors accept standard 4 mm plugs. Use of high quality plugs and speaker cable are recommended. Table 2−3. Description of Loudspeaker Connectors Reference Designator Caution Both positive and negative speaker outputs are floating and may NOT be connected to ground (f.ex.
  • Page 19: Description Of Switches And Buttons

    2.5 Description of Switches and Buttons 2.5.1 S/PDIF Input Selector Switch (S100) S100 switches between optical and coaxial S/PDIF input. When the lever is pressed in the direction of J101, the optical S/PDIF input is selected. When the lever is pressed in the direction of J100, the coaxial S/PDIF input is selected. 2.5.2 Bypass Digital Audio Processor Switch (S320) When the lever is pressed in the direction of S341, the DAP is bypassed.
  • Page 20: Description Of Indicators

    Description of Indicators 2.6 Description of Indicators 2.6.1 Power LED (LED223) green TAS5010−5112F2EVM board is powered on. 2.6.2 No S/PDIF Input LED (LED222) The yellow LED indicates that the S/PDIF input signal is missing or it does not contain valid audio data. Reasons to have a No S/PDIF warning: The lever at the S/PDIF input selector switch (S100) is placed in the wrong position.
  • Page 21: Evm Board Operation

    EVM Board Operation This chapter describes the TAS5010−5112F2EVM board operation. Topic Power Supply ..........Setup the TAS5010-5112F2EVM With the S/PDIF Input Setup the TAS5010-5112F2EVM With the Analog Line Input Interfacing the Analog Line Output...
  • Page 22: Power Supply

    Power Supply 3.1 Power Supply The TAS5010−5112F2EVM can be powered from one or two external power supplies. High-end audio performance requires a stabilized power supply with low ripple voltage and low output impedance. Note: The length of the power supply cable must be minimized. Increasing the length of the PSU cable is equal to increasing the distortion for the amplifier at high output levels and low frequencies.
  • Page 23: Setup The Tas5010−5112F2Evm With The S/Pdif Input

    3.2 Setup the TAS5010−5112F2EVM With the S/PDIF Input Connect the EVM board as shown in Figure 3−2. Select between coaxial or optical input signal at the input selector switch (S100). Press the lever at S320 in the direction of U360 if the TAS3002 DAP is wanted in the signal path (recommended during normal listening tests).
  • Page 24: Start-Up Sequence

    Setup the TAS5010−5112F2EVM With the Analog Line Input 3.2.1 Start-up Sequence 1) Turn on the power supply/supplies. Follow the power-up and power-down sequence described in the Power Supply section. Observe that the green Power ON LED and the yellow No S/PDIF LED are lit. 2) Run the DCT software from the PC desktop if the DAP is activated (S320) and the attached cable is connected from J300 to the PC.
  • Page 25: Hints For Measurement Of Performance

    Chapter 4 Hints for Measurement of Performance Read the Digital Audio Measurements application note (SLAA114) for an introduction to measurements on true digital audio amplifiers. You are welcome to use the audio precision test files available on the PurePath Digital™ amplifier CD-ROM. Note that an AES17 filter is required to reach the shown measurements.

This manual is also suitable for:

Tas5010−5112f2evm

Table of Contents