Homelite HBLT25CD Operator's Manual page 8

Original instructions
is lying on a flat and bare surface.
Starting a cold engine:
1. Ensure the switch is in the "I" (ON) position.
2. Press the primer bulb 10 times.
NOTE: After the 7th press, the fuel should be visible in
the primer bulb. If not, continue pressing until the fuel
is visible.
3. Set the choke lever to
4. Squeeze the throttle trigger completely and pull the
starter grip until the engine attempts to start. Do not pull
the starter grip more than 4 times.
NOTE: Keep the throttle trigger squeezed completely
through steps 4 to 7.
5. Set the choke lever to
6. Pull the starter grip until the engine starts. Do not pull
the starter grip for more than 6 times.
NOTE: If the engine does not start, return to
position and repeat the process beginning at step 2.
7. Allow the engine to run for 10 seconds, then set the
choke lever to position.
Starting a warm engine:
1. Ensure the switch is in the "I" (ON) position.
2. Press the primer bulb 10 times.
3. Set the choke lever to
4. Pull the starter grip until the engine attempts to start. Do
not pull the starter grip for more than 6 times.
NOTE: If the engine does not start, return to step 2
under "Starting a cold engine".
STOPPING THE PRODUCT
■ Release the throttle trigger.
■ Hold the engine switch in the "STOP" (OFF) position.
OPERATING THE TRIMMER
Follow these steps to operate the curved shaft trimmer.
■ Start the trimmer.
■ Hold the trimmer at waist level with your right hand on
the rear handle and your left hand on the front handle.
■ Place the product on the right side of your body with the
engine behind and away from your body.
■ Trim the grass and weeds with the line parallel to the
ground.
WARNING
Injuries may be caused, or aggravated, by prolonged use
of the product. When using any product for prolonged
periods, ensure you take regular breaks.
NOTE: Always operate the trimmer at full throttle.
Prolonged cutting at partial throttle will result in oil dripping
from the silencer.
CUTTING TIPS
Cut tall grass from the top down. This will prevent grass
from wrapping around the shaft housing and PRO-CUT I
head, which may cause damage from overheating. If grass
8
| English
choke position.
choke position.
choke
position.
becomes wrapped around the PRO-CUT I head, stop the
engine, wait for all moving parts to stop, and remove the
MAINTENANCE
grass.
WARNING
When servicing, use only original manufacturer's
replacement parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
Always wear safety goggles or safety glasses with side
shields during product operation. If operation is dusty,
also wear a dust mask.
WARNING
Before inspecting, cleaning, or servicing the product,
shut off the engine and wait for all moving parts to stop.
Failure to follow these instructions can result in serious
personal injury or property damage.
WARNING
Neglected or poorly conducted maintenance may create
additional hazards. Do not attempt to repair or maintain
the product if you are not qualified to do so. If in doubt,
return to a service centre for professional assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, and grease.
WARNING
Do not at any time let brake fluids, petrol, petroleum-
based products, penetrating lubricants, etc., come in
contact with plastic parts. Chemicals can damage,
weaken or destroy plastic, which may result in serious
personal injury.
You can often make adjustments and repairs described in
this manual. For other repairs, have the trimmer serviced
by a service agent.
REPLACING THE PRO CUT I STRING HEAD AND LINE
■ Stop the engine and wait for all moving parts to stop
completely.
■ Loosen the spool retainer by turning it counterclockwise
and then remove the string head.
■ Take a new PRO-CUT I string head and a 500 mm
length of 2.4 mm thick monofilament pre-cut line.
■ Place the middle of the line under the hook/notch inside
the spool.