Instructions For Operation; Before Operation - Max SuperLocator SN438J Operating Instructions Manual

2. AIR SUPPLY AND CONNEC-
TIONS (Fig.2)
A. TOOL AIR FITTINGS/COUPLIGS:
This tool uses a 1/4" N.P.T. male plug. The inside diameter
should be .28" / 7 mm or larger. Install a male plug on the tool
which is free flowing and which will release air pressure from the
tool when disconnected from the supply source.
B. OPERATING PRESSURE:
70 to 100 p.s.i. / 5 to 7 bar. Select the operating air pressure with-
in this range for best performance based upon the fastener appli-
cation and work surface. Using the lowest acceptable to minimize
noise, vibration and wear.
DO NOT EXCEED 120 p.s.i. / 8 bar.
C. HOSES 1 :
Hose has a min. diameter of 1/4" / 6 mm and max. length of no
more than 17' / 5 m.
The supply hose should contain a fitting that will provide "quick
disconnecting" from the male plug on the tool.
D.SUPPLY SOURCE 2 :
Use only clean regulated compressed air with pressure regulated
not to exceed maximum air pressure marked on the tool.
If regulator fails, maximum air pressure delivered to tool shall
not exceed 200 p.s.i / 13.8 bar or 1.5 times maximum air pres-
sure, whichever is greater.
E. 3-PIECE AIRSET 3
(Air filter 4 , Regulator 5 , Oiler 6 ):
To optimize performance use a 3-piece air set 3 . A filter 4 will
help to get the best performance and minimum wear from the tool
because dirt and water in the air supply are major causes of wear
in the tool.
Frequent, but not excessive, lubrication (one drop in every 100-
200 nails) is required for the best performance. Oil added through
the air line connection will lubricate the internal parts.

3. INSTRUCTIONS FOR OPERATION

1.

BEFORE OPERATION

Check the following prior operation.
1 Wear Safety Glasses or Goggles.
2 Do not connect the air supply.
3 Inspect screw tightness.
4 Check operation of the contact arm & trigger if moving
smoothly.
5 Connect the air supply.
6 Check the air leakage. (The Tool must not have the air
leakage.)
7 Hold the Tool with finger-off the trigger, then push the con-
tact arm against the work-piece. (The tool must not oper-
ate.)
8 Hold the Tool with contact arm free from work-piece and pull
the trigger. (The Tool must not operate.)
9 Disconnect the air supply.
2. OPERATION
NAIL LOADING
1 (Fig.3) Load the nails 1 into the slot in the rear of the Mag-
azine until they go over the Nail Stopper 2.
2 (Fig.4) Pull the Pusher 1 as far as the rear end of the mag-
azine and release it gently.
(Fig12.) Always point exposed first nail away yourself and
others.
Keep your face, hands, feet, other body parts as well as
those of other person away from the nose muzzle to avoid
possible injury during usage and carrying.
TEST OPERATION
1 Adjust the air pressure at 70 p.s.i. / 5bar and connect the air
supply.
2 Without touching the Trigger, depress the Contact Arm
against the workpiece.
Pull the Trigger. (The tool should fire the fastener.)
3 With the tool off the workpiece, pull the Trigger.
Then depress the Contact Arm against the workpiece. (The
tool must not fire the fastener.)
4 Adjust the air pressure as much as the lowest possible ac-
cording to the diameters and length of fastener and the
hardness of workpiece.
DRIVING FASTENERS
This is "SINGLE FIRE OPERATION" tool.
1 (Fig.9) Be sure to position and insert the first fastener point
through the hole in the metal connector with finger off the
trigger.
2 (Fig.10) Keep the tool vertically when driving. To avoid the
slipping fasteners, do not push the tool forward when posi-
tioning the first fasteners into metal hole.
3 (Fig.11) Pull the trigger to drive a fastener with keep your
face and hands away from the nose. If the moveable nose
does not detect the work surface close to the nose of the
tool, the tool will not actuate.
4 Remove finger from the trigger. Remove the tool from work-
piece and reposition into the next pre-punched metal hole.
Repeat same process.
TO AVOID SERIOUS INJURY FROM FASTENERS AND
FLYING DEBRIS WHEN INSTALLING METAL CONNEC-
TORS USING THE TOOL:
Metal connector nails are not designed to penetrate
metal. (Fig.9) When installing metal connectors, always
place the exposed point of the metal connector nail into
the metal connector's preformed hole, and orient so the
nail is perpendicular to the hole before attempting to
drive a fastener.
REMOVING JAMMED NAILS (Fig.5, 6, 7, 8)
ALWAYS disconnect the air supply.
Wear gloves when removing jams; do not use bare hands.
Confirm that you have removed all fasteners from nose of
tool before reconnecting to the air supply.
1 Disconnect the air supply.
2 Push down the Pusher Lever 1 and release the strip nails
from the Pusher 3.
3 Push the Nail Stopper 2, and remove the strip nails from
inside of the Magazine.
4 Pull and stayed the Pusher 3 with hand.
5 Remove the jammed nail from the Nose using a punch or a
slotted screw driver.
6 If the collation strip is broken, it is likely that there are nails 2
remaining in the Nose even if you have removed all nails.
Check thoroughly that you have removed all nails before re-
connecting the tool to the air supply.
3