Grundfos MAGNA3 Menu Overview

Grundfos MAGNA3 Menu Overview

Display menu overview
Hide thumbs Also See for MAGNA3:
Table of Contents

Advertisement

Available languages

Available languages

APPLICATION
WIZARD
MAGNA3
Home
Status Settings Assist
Control mode
Setpoint
6.5
AUTO
m
ADAPT
Estimated flow rate
Head
8
4.0
m
m
3
/h
MAGNA3
GRUNDFOS INSTRUCTIONS
DISPLAY MENU
OVERVIEW
Valid from
model D
GB / DE

Advertisement

Chapters

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MAGNA3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Grundfos MAGNA3

  • Page 1 GRUNDFOS INSTRUCTIONS MAGNA3 APPLICATION WIZARD DISPLAY MENU OVERVIEW Valid from model D GB / DE Home Status Settings Assist Control mode Setpoint AUTO ADAPT Estimated flow rate Head MAGNA3...
  • Page 2: Table Of Contents

    HOME STATUS SETTINGS ASSIST Operating status Setpoint Application wizard » Operating mode, from » Boiler pump » Control mode Operating mode » Radiator » Fan coil unit » Normal Pump performance » Air handling unit » Stop » Underfloor/ceiling » Max. curve and duty point »...
  • Page 3: Operating Mode

    SETTINGS Operating mode The pump runs according to the selected control Status icons in display footer Normal mode. Operating mode overrules control mode. Control mode See next page AUTO ADAPT = Automatic night setback FLOW ADAPT Prop. press. Const. press. = Change of settings - locked Const.
  • Page 4: Control Mode

    SETTINGS Make sure that the operating mode is set to ”Normal” in order for the pump to run according Control mode to the available control modes. The table shows the different control modes along with a recommended application type. Recommended for most heating systems. During operation, the pump automatically AUTO ADAPT makes the necessary adjustment to the actual system characteristic.
  • Page 5: Analog Input

    SETTINGS Analog input External setpoint influence Function of analog input This function can be used in the following control modes: External sensor feedback The most commonly used Constant curve control mode for external setpoint function. Building These operating modes are designed for the Management System/PLC connection of an external sensor:...
  • Page 6: Assist

    Assist Application wizard The application wizard in the Assist menu helps you set the correct control mode. Heating and hot water systems Firstly, identify your pump in the application overview below. Secondly, in the pump’s display, choose the system that applies to the position of your pump.
  • Page 7: Ground Source

    Assist Application wizard The application wizard in the Assist menu helps you set the correct control mode. Ground source heat pump system Example: Ground source Firstly, identify your pump in the application overview to the left. Secondly, choose “Ground source” in the application wizard and press “OK”. Then select either “Ground loop”...
  • Page 8: Chiller Pump

    Assist » Air handling unit Application wizard The application wizard in the Assist menu helps you set the correct control mode. Cooling systems Firstly, identify your pump in the application overview below. Secondly, in the pump’s display, choose the system that applies to the position of your pump.
  • Page 9: Multipump Setup

    CIMs, making it possible only to mount the CIM on the master pump. See installation Master master loses power, the input of the slave will and operating instructions for MAGNA3 model D for a list of supported CIM versions. module (CIM)* take over.
  • Page 10 The temperature sensor must only be installed only done on one of the pumps. on the master pump. However, Grundfos Eye and relays are local and show the status of each individual pump (e.g. running, stopped and warning). Autonomous twin-head pump control...
  • Page 11 Warning 77 – Multipump communication • If the error continues, contact Grundfos Service. • A yellow Grundfos Eye indicates the warning. Both pumps in Alarm 10 – Internal fault the multipump system will continue to operate according to their local settings.
  • Page 12: Auto Adapt » Flow Adapt

    STARTSEITE STATUS EINSTELLUNGEN ASSISTENT Betriebsstatus Sollwert Anwendungsassistent » Betriebsart, von » Heizkesselpumpe » Regelungsart Betriebsart » Heizkörper » Gebläsekonvektor » Normal Pumpenleistung » Lüftungsanlage » Stopp » Fußboden/Decke » MAX-Kennlinie und Betriebspunkt » Min. » Warmwasser » Max. » Erdwärme »...
  • Page 13: Einstellungen

    EINSTELLUNGEN Betriebsart Die Pumpe läuft entsprechend der ausgewählten Status-Symbole am unteren Bildschirmrand Normal Regelungsart. Die Betriebsart übersteuert die Regelungsart. Regelungsart Siehe nächste Seite AUTO ADAPT = Automatische Nachtabsenkung FLOW ADAPT Proportionaldruck Konstantdruck = Ändern von Einstellungen ist gesperrt Konstanttemperatur Differenztemperatur = An Feldbus angeschlossen Konstanter Durchfluss Konstantkennlinie...
  • Page 14: Regelungsart

    EINSTELLUNGEN Vergewissern Sie sich, dass die Betriebsart „Normal“ eingestellt ist, damit die Pumpe gemäß Regelungsart den verfügbaren Regelungsarten läuft. In der Tabelle sind die verschiedenen Regelungsarten und die empfohlenen Anwendungsarten aufgeführt. Wird für die meisten Heizungsanlagen empfohlen. Während des Betriebs passt sich AUTO ADAPT die Pumpe automatisch an die vorliegende Anlagencharakteristik an.
  • Page 15: Analogeingang

    EINSTELLUNGEN Analogeingang Externe Sollwertverschiebung Funktion des Analogeingangs Diese Funktion kann in Verbindung mit den folgenden Regelungsarten verwendet werden: Rückmeldung vom externen Sensor Diese Regelungsart wird am Konstantkennlinie häufigsten für die externe Sollwertverschiebung verwendet. Building Die folgenden Betriebs-/Regelungsarten sind Management System/SPS für die Verwendung mit einem externen Sensor Konstantdruck vorgesehen:...
  • Page 16: Assistent

    Assistent Anwendungsassistent Der Anwendungsassistent im Menü „Assistent“ hilft Ihnen dabei, die richtige Regelungsart einzustellen. Heizungs- und Warmwasseranlagen Bestimmen Sie zunächst Ihre Anlage und Pumpe in der Anwendungsübersicht unten. Wählen Sie dann im Display der Pumpe die Anlage aus, die in Bezug auf die Position der Pumpe Ihrer Anlage entspricht.
  • Page 17: Erdwärme

    Assistent Anwendungsassistent Der Anwendungsassistent im Menü „Assistent“ hilft Ihnen dabei, die richtige Regelungsart Erdwärmepumpenanlage einzustellen. Beispiel: Erdwärme Bestimmen Sie zunächst Ihre Anlage und Pumpe in der Anwendungsübersicht links. Wählen Sie dann im Anwendungsassistenten „Erdwärme“ aus und drücken Sie auf „OK“. Wählen Sie anschließend je nach Position der Pumpe entweder „Erdwärmekreis“...
  • Page 18: Kühlpumpe

    Assistent » Lüftungsanlage Anwendungsassistent Der Anwendungsassistent im Menü „Assistent“ hilft Ihnen dabei, die richtige Regelungsart Kühlanlagen einzustellen. Bestimmen Sie zunächst Ihre Anlage und Pumpe in der Anwendungsübersicht unten. Wählen Sie dann im Display der Pumpe die Anlage aus, die in Bezug auf die Position der Pumpe Ihrer Anlage entspricht.
  • Page 19: Mehrpumpenkonfiguration

    Master Feldbus-Modul Eingang ignoriert. Wird die Master-Pumpe Master-Pumpe zu montieren. Eine Liste der unterstützten CIM-Ausführungen (CIM)* nicht mehr mit Strom versorgt, übernimmt finden Sie in der Montage- und Betriebsanleitung des Modells D der MAGNA3. der Eingang der Slave-Pumpe die Regelung.
  • Page 20 Pumpen erforderlich. Der Temperatursensor muss nur an der Master-Pumpe installiert werden. Das Grundfos Eye und die Relais sind pumpenspezifische Vorrichtungen und zeigen somit immer den Status der jeweiligen Pumpe an (z. B. läuft, abgeschaltet, Warnung).
  • Page 21: Alarme Und Warnungen

    Alarme und Warnungen Alarm 72 – Interne Störung • Wenn das Grundfos Eye rot leuchtet, bedeutet dies, dass ein Alarm vorliegt. Die Pumpe schaltet sich ab und versucht automatisch neu zu starten. Warnung 88 – Interne Sensorstörung • Es ist möglich, dass es in der Anwendung zu einem ungewollten Zwangsdurchfluss durch die Pumpe kommt, der von anderen Geräten verursacht wird.
  • Page 23 99123107 0818 ECM: 1241084 GRUNDFOS Holding A/S Poul Due Jensens Vej 7 DK-8850 Bjerringbro Tlf.: +45-87 50 14 00...

Table of Contents